Engineering topics

Lessard, Wendy B.

Publications and source records attributed to Lessard, Wendy B..

10 records

NASA NTRS2006

Test and Analysis of Foam Impacting a 6x6 Inch RCC Flat Panel

This report presents the testing and analyses of a foam projectile impacting onto thirteen 6x6 inch flat panels at a 90 degrees incidence angle. The panels tested in this investigation were fabricated of Reinforced-Carbon-Carbon material and were used to aid in the validation of an existing material model, MAT58. The computational analyses were performed using LS-DYNA, which is a physics-based, nonlinear, transient, finite element code used for analyzing material responses subjected to high impact forces and other dynamic conditions. The test results were used to validate LS-DYNA predictions and to determine the threshold of damage generated by the MAT58 cumulative damage material model. The threshold of damage parameter represents any external or internal visible RCC damage detectable by nondestructive evaluation techniques.

Lessard, Wendy B.↗

NASA NTRS2003

Evaluation of a Singular Value Decomposition Approach for Impact Dynamic Data Correlation

Impact dynamic tests are used in the automobile and aircraft industries to assess survivability of occupants during crash, to assert adequacy of the design, and to gain federal certification. Although there is no substitute for experimental tests, analytical models are often developed and used to study alternate test conditions, to conduct trade-off studies, and to improve designs. To validate results from analytical predictions, test and analysis results must be compared to determine the model adequacy. The mathematical approach evaluated in this paper decomposes observed time responses into dominant deformation shapes and their corresponding contribution to the measured response. To correlate results, orthogonality of test and analysis shapes is used as a criterion. Data from an impact test of a composite fuselage is used and compared to finite element predictions. In this example, the impact response was decomposed into multiple shapes but only two dominant shapes explained over 85% of the measured response

Horta, Lucas G.↗

NASA NTRS2002

Modal and Impact Dynamics Analysis of an Aluminum Cylinder

This paper presents analyses for the modal characteristics and impact response of an all-aluminum cylinder. The analyses were performed in preparation for impact tests of the cylinder at The Impact Dynamics Research Facility (IDRF) at the NASA Langley Research Center. Mode shapes and frequencies were computed using NASTRAN and compared with existing experimental data to assess the overall accuracy of the mass and stiffness of the finite element model. A series of non-linear impact analyses were then performed using MSC Dytran in which the weight distribution on the floor and the impact velocity of the cylinder were varied. The effects of impact velocity and mass on the rebound and gross deformation of the cylinder were studied in this investigation.

Lessard, Wendy B.↗

NASA NTRS2000

Analysis of Post-Support and Wind-Tunnel Wall Interference on Flow Field About Subsonic High-Lift High-Speed Research Configuration

The present study was performed to determine how significant the interference effects of the wind-tunnel model support system and tunnel walls can be for a high-speed configuration during takeoff and landing conditions. A 5-percent scale model of the Technology Concept Airplane was recently tested in the Langley 14- by 22-Foot Sub-sonic Tunnel. The model was numerically modeled with and without the support and tunnel walls and compared with experimental data. Detailed analysis of the flow provided additional insight concerning what effects the post support and tunnel walls had on the flow field. This study revealed that although the overall forces and moments could be experimentally accounted for, the detailed flow features, such as the surface pressure distributions, could not be accurately simulated without including the post support in the computations.

Lessard, Wendy B.↗

NASA NTRS1999

Navier-Stokes Simulation of Several High-Lift Reference H Configurations

The subsonic flow field was numerically simulated around several High Speed Research Reference H configurations at various pitch and yaw angles. A sequence of structured-viscous grids were generated; the first grid modeled the wing-body high-lift geometry, and the second grid incorporated the nacelles and the horizontal tail. The third grid modeled the full-span geometry for sideslip calculations, and was obtained by mirroring a coarser version of the second grid. The CFL3D code, a Reynolds averaged, thin-layer Navier-Stokes flow solver for structural grids, was used for the flow solver and modeled the free-air Reference H high-lift configuration at wind tunnel conditions of Mach number 0.24 and Reynolds number of 1.4 x 10(exp 5) per in. Pitch sweeps were performed at angles of attack from 6 deg to 15 deg. Sideslip angle sweeps at 0 deg <= Beta <= +18 deg were performed at an angle of attack of 8 deg. The lateral and longitudinal performance characteristics were well predicted and very good force and moment comparisons were obtained. A very complex multiple vortical system develops at the higher angles of attack, and detailed postprocessing of the solutions provided a comprehensive three-dimensional understanding of the flow which helps to correlate and interpret the wind tunnel data.

Lessard, Wendy B.↗

NASA NTRS1999

High-Lift CFD Validation

It is not unusual when comparing CFD data to experimental data to find discrepancies between the results. Sometimes forces and moments compare well, while surface pressures do not, and vice versa. It is commonplace for the researcher to believe that the flow field has been accurately simulated when these types of measurements compare well. However, being able to routinely predict boundary layer transition and separated flows are not guaranteed. In fact accurate simulation of these types of flow physics has been a challenge to the CFD community. In order to improve Navier-Stokes predictions for complex vortical flow fields, more detailed information about the flow physics is necessary. Unfortunately, the many wind-tunnel tests performed in Langley's NTF and 14x22 facilities as well as in the Ames' 12 ft. Tunnel provided little information about the detailed flow physics, and no priority was given to obtaining any CFD measurements. Using the latest experimental techniques, this information can and should be obtained for present and future use.

Lessard, Wendy B.↗

NASA NTRS1999

Code Calibration Applied to the TCA High-Lift Model in the 14 x 22 Wind Tunnel (Simulation With and Without Model Post-Mount)

The objective of this study is to calibrate a Navier-Stokes code for the TCA (30/10) baseline configuration (partial span leading edge flaps were deflected at 30 degs. and all the trailing edge flaps were deflected at 10 degs). The computational results for several angles of attack are compared with experimental force, moments, and surface pressures. The code used in this study is CFL3D; mesh sequencing and multi-grid were used to full advantage to accelerate convergence. A multi-grid approach was used similar to that used for the Reference H configuration allowing point-to-point matching across all the trailingedge block interfaces. From past experiences with the Reference H (ie, good force, moment, and pressure comparisons were obtained), it was assumed that the mounting system would produce small effects; hence, it was not initially modeled. However, comparisons of lower surface pressures indicated the post mount significantly influenced the lower surface pressures, so the post geometry was inserted into the existing grid using Chimera (overset grids).

Lessard, Wendy B.↗

NASA NTRS1999

A CFD Assessment of Several High-Lift Reference H Configuration Using Structured Grids

The objective of this study is to calibrate a Navier-Stokes code for a high-lift Reference H configuration using structured grids. The outline of this presentation will first include a brief description of the grids used and the flow solver. Next the results will be presented in terms of convergence and resources used on the C-90. Predicted force and moment and surface pressure results are compared to experiment and off- and on-surface flow viz. is discussed.

Lessard, Wendy B.↗

NASA NTRS1996

Subsonic Analysis of 0.04-Scale F-16XL Models Using an Unstructured Euler Code

The subsonic flow field about an F-16XL airplane model configuration was investigated with an inviscid unstructured grid technique. The computed surface pressures were compared to wind-tunnel test results at Mach 0.148 for a range of angles of attack from 0 deg to 20 deg. To evaluate the effect of grid dependency on the solution, a grid study was performed in which fine, medium, and coarse grid meshes were generated. The off-surface vortical flow field was locally adapted and showed improved correlation to the wind-tunnel data when compared to the nonadapted flow field. Computational results are also compared to experimental five-hole pressure probe data. A detailed analysis of the off-body computed pressure contours, velocity vectors, and particle traces are presented and discussed.

Lessard, Wendy B.↗

NASA NTRS1996

Improved Method for Prediction of Attainable Wing Leading-Edge Thrust

Prediction of the loss of wing leading-edge thrust and the accompanying increase in drag due to lift, when flow is not completely attached, presents a difficult but commonly encountered problem. A method (called the previous method) for the prediction of attainable leading-edge thrust and the resultant effect on airplane aerodynamic performance has been in use for more than a decade. Recently, the method has been revised to enhance its applicability to current airplane design and evaluation problems. The improved method (called the present method) provides for a greater range of airfoil shapes from very sharp to very blunt leading edges. It is also based on a wider range of Reynolds numbers than was available for the previous method. The present method, when employed in computer codes for aerodynamic analysis, generally results in improved correlation with experimental wing-body axial-force data and provides reasonable estimates of the measured drag.

Carlson, Harry W.↗