Search NASA⌕ Search

Engineering topics

Li, Bingjun

Publications and source records attributed to Li, Bingjun.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Comparison of Mg-based liquid metal ion sources for scalable focused-ion-implantation doping of GaN

We compare the suitability of various magnesium-based liquid metal alloy ion sources (LMAISs) for scalable focused-ion-beam (FIB) implantation doping of GaN. We consider GaMg, MgSO 4 $\bullet$7H 2 O, MgZn, AlMg, and AuMgSi alloys. Although issues of oxidation (GaMg), decomposition (MgSO 4 $\bullet$7H 2 O), and excessive vapor pressure (MgZn and AlMg) were encountered, the AuMgSi alloy LMAIS operating in a Wien-filtered FIB column emits all Mg isotopes in singly and doubly charged ionization states. We discuss the operating conditions to achieve <20 nm spot size Mg FIB implantation and present Mg depth profile data from time-of-flight secondary ion mass spectrometry. We also provide insight into implantation damage and recovery based on cathodoluminescence spectroscopy before and after rapid thermal processing. Prospects for incorporating the Mg LMAIS into high-power electronic device fabrication are also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Unveiling the influence of selective-area-regrowth interfaces on local electronic properties of GaN p-n junctions for efficient power devices

Here, we report correlated nanoscale mapping of the structure, composition, and properties of regrown GaN p-n junctions to identify how etching and non-planar regrowth processes limit diode performance via the introduction of unintentional dopants and defect states. p-GaN was selectively regrown in n-GaN trenches with SiO 2 masks of variable mask-to-trench-width ratio. Dilute Al layers were periodically introduced during regrowth as markers of the growth interface. Correlated nanoscale mapping of doping, conductivity, and dopant complexes was achieved with atom probe tomography (APT), scanning spreading resistance microscopy (SSRM), and cathodoluminescence (CL) spectroscopy, respectively. The Al marker layers, detected by APT, enabled reconstruction of the faceted growth interface and correlation of the dopant concentration with position and time. The p-GaN growth rate is proportional to the mask-to-trench width ratio while the dopant incorporation rate is invariant. At trench edges, magnesium incorporation is suppressed, and oxygen incorporation enhanced, due to preferential incorporation on the semi-polar growth surface, leading to compensation and less abrupt p-n junctions; the SiO 2 mask is a source of oxygen. Residual etch damage below the regrowth interface induces n-type and p-type conductivity, creating leakage pathways. The non-uniform Mg incorporation is driven by crystal anisotropy and is thus inherent to non-planar regrowth, but can be mitigated by engineering the regrowth interface and process parameters. The unprecedented integration of spatially resolved mapping of dopants, impurities, conductivity, and carrier type is a powerful approach to discriminating distinct factors that limit the performance of regrown diodes, enabling the rational optimization of process and device design.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Etched-And-Regrown GaN P–N Diodes with Low-Defect Interfaces Prepared by In Situ TBCl Etching

The ability to form pristine interfaces after etching and regrowth of GaN is a prerequisite for epitaxial selective area doping, which in turn is needed for the formation of lateral PN junctions and advanced device architectures. In this work, we report the electrical properties of etched-and-regrown GaN PN diodes using an in situ Cl-based precursor, tertiary butylchloride (TBCl). We demonstrated a regrowth diode with I–V characteristics approaching that from a continuously grown reference diode. The sources of unintentional contamination from the silicon (Si) impurity and the mediating effect of Si during the TBCl etching are also investigated in this study. Furthermore, this work points to the potential of in situ TBCl etching toward the realization of GaN lateral PN junctions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A study of damage-free in-situ etching of GaN in metalorganic chemical vapor deposition (MOCVD) by tertiarybutylchloride (TBCl)

This paper reports a study of the effect of NH 3 flow rate and reactor temperature on the tertiarybutylchloride (TBCl) etching of patterned GaN-on-sapphire templates. It is found that a reduced NH 3 flow rate and an elevated reactor temperature can eliminate islands or dots on the surface, while at the same time, enhance the etching around dislocations. TBCl etching was also performed on planar bulk GaN templates with much lower dislocation density. We find an atomically flat and layer-by-layer etching behavior within the region free of dislocations. Surface kinetics analysis reveals a short diffusion length of etching products. Room-temperature photoluminescence (PL) and x-ray photoelectron spectroscopy (XPS) measurements confirm that TBCl etching is capable of removing the damage and impurities induced by plasma etching without introducing additional damage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗