Search NASA⌕ Search

Engineering topics

Lindgren, Eric R.

Publications and source records attributed to Lindgren, Eric R..

At least 37 records · Page 2

Development of Mockups and Instrumentation for Spent Fuel Drying Tests

The purpose of this report is to provide updates on the experimental components, methodology, and instrumentation under development for use in advanced studies of realistic drying operations conducted on surrogate spent nuclear fuel. Validation of the extent of water removal in a dry spent nuclear fuel storage system based on drying procedures used at nuclear power plants is needed to close existing technical gaps. Operational conditions leading to incomplete drying may have potential impacts on the fuel, cladding, and other components in the system. Water remaining in canisters upon completion of drying procedures can lead to cladding corrosion, embrittlement, and breaching, as well as fuel degradation. Additional information is needed on the drying process efficacy to help evaluate the potential impacts of water retention on extended longterm dry storage. A general lack of data suitable for model validation of commercial nuclear canister drying processes necessitates additional, well-designed investigations. Smaller-scale tests that incorporate relevant physics and well-controlled boundary conditions are essential to provide insight and guidance to the simulation of prototypic systems undergoing drying processes. This report describes the implementation of moisture monitoring equipment on a pressurized, submersible system employing a single waterproof, electrically heated spent fuel rod simulator as a demonstration of analytical capabilities during a drying process. A mass spectrometer with specially designed inlets was used to monitor moisture and other gases at 150 kPa to 800 kPa for a test simulating a forced helium dehydration procedure and below 1 torr for tests mimicking a vacuum drying process. The dew point data from the mass spectrometer was found to be in good agreement with a solid-state moisture probe. A distinct advantage of the mass spectrometer system was the capability to directly sample from the hightemperature (>200 °C) head space expected in a prototypic scale experiment where a solid-state moisture probe would suffer considerable loss of accuracy or fail altogether. The operational and analytical experiences gained from this test series are poised to support an expansion to assembly-scale tests at prototypic length. These assemblies are designed to feature prototypic assembly hardware, advanced diagnostics for in situ internal rod pressure monitoring, and failed fuel rod simulators with engineered cladding defects to challenge the drying system with waterlogged fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Accelerated Testing of Selected Filler Compositions

The fillers R&D program, mostly experimental, is part of a broader R&D program that includes new process modeling and performance assessment of criticality effects and the overall importance of criticality to repository performance (consequence screening). A literature research and consultation effort with experts by Hardin and Brady (2018) identified several potentially effective and workable filler materials including cements (primarily phosphate based), molten-metal alloys, and low-temperature glasses. Filler attributes were defined and the preliminary lists were compared qualitatively. Further comparative analysis will be done (e.g., cost estimates) after experimental screening has narrowed the list of alternatives. The following cement filler compositions were selected for experimental development work and accelerated testing in FY19: Aluminum phosphate cements (APCs); more specifically aluminum oxide / aluminum phosphate (Al 2 O 3 / AlPO 4 ) cements in which Al 2 O 3 serves as the filler material bound by an AlPO 4 binder formed by the reaction of Al 2 O 3 with H 3 PO 4 ; Calcium phosphate cements (CPCs); more specifically composed of pure or nearly pure hydroxyapatite (Ca 5 (PO 4 ) 3 (OH)); Magnesium potassium phosphate cements (MKPs) composed of magnesium oxide / magnesium potassium phosphate (MgO / MgKPO 4 ) cements in which MgO serves as the filler and MgKPO 4 serves as the binder formed by the reaction of MgO with monopotassium phosphate (KH 2 PO 4 ) and tricalcium phosphate ((Ca 3 (PO 4 ) 2 ); Two additional potential cement materials were explored preliminarily as the result of: (1) continued literature investigations into other filler candidates (wollastonite-based phosphate ceramic) and (2) the experimental discovery of a well-consolidated fly ash phosphate cement during the evaluation of fly ash as a potential filler material with Al 2 O 3 in APCs. Fly ash phosphate cements, more specifically in which a fly ash material composed primarily of mullite and quartz serves as the filler and is reacted with H 3 PO 4 to form amorphous phosphate phase(s) as the binder; Wollastonite aluminum phosphate cements (WAPC), specifically wollastonite / aluminum phosphate (CaSiO 3 / AlPO 4 ) in which CaSiO 3 serves as the filler material and AlPO 4 serves as the binder formed by Al(OH) 3 or metakaolin as Al sources and H 3 PO 4 or ammonium dihydrogen phosphate (ADP) (NH 4 H 2 PO 4 ) as phosphate sources. The FY19 effort focused on the optimization of compositions and subsequent processing of these five materials to achieve dense and well-consolidated monolithic samples with relatively low porosity. Once these goals were met basic material properties screening evaluations were performed including an assessment of dissolution resistance in water at elevated temperature (200 °C) and mechanical testing including unconfined compressive strength (UCS) testing. To date, the aluminum phosphate cements (APCs) appear to show the most promise for continued development. They are easily prepared and form smooth pourable slurries that remain stable for days with relatively low viscosities of several thousand centipoise (cP). They are then set at elevated temperatures (e.g., 170 °C) under ambient (0.1 MPa) or elevated pressure (~1MPa). Overall, they demonstrate the best dissolution resistance in water at elevated temperature (200 °C) and good compressive strengths. However, additional effort is required to optimize the APC slurry formulations and the process used for thermal curing these materials. The calcium phosphate cements (CPCs) can be formed at room temperature to produce a well-consolidated body. However, their slurry viscosities are very high (and difficult to measure) and they exhibit relatively short cure times of 2 to 3 hours. Also, dissolution resistance is very poor, the poorest of all the cements examined The same is the case for the small number of MKP cements fabricated; they cure very quickly (10 minutes or less) and disintegrate within a few hours upon immersion in distilled water. Surprisingly, fly ash reacts with phosphoric acid to form dense and well-consolidated cements but the mixture rapidly sets at room temperature (less than 30 minutes) and the subsequent conversion of the binder to an amorphous phosphate phase(s) as a function of temperature is complicated. Finally, the wollastonite aluminum phosphate cements (WAPC) are easily prepared and form smooth pourable slurries that remain stable for several hours. They are then set at 130 °C. A WAPC sample exhibited the highest compressive strengths of all the materials we evaluated but in general their dissolution resistance to water is poor.

36 MATERIALS SCIENCE↗

Advanced Concepts for Dry Storage Cask Thermal-Hydraulic Testing

The purpose of this report is to review technical issues relevant to the performance evaluation of dry storage systems during vacuum drying and long-term storage operations. It also provides updates on experimental components under development that are vital for pursuing advanced studies. Validation of the extent of water removal in a multi-assembly dry storage system using an industrial vacuum drying procedure is needed, as operational conditions leading to incomplete drying may have potential impacts on the fuel, cladding, and other components in the system. Water remaining in canisters/casks upon completion of vacuum drying can lead to cladding corrosion, embrittlement, and breaching, as well as fuel degradation. Therefore, additional information is needed to evaluate the potential impacts of water retention on extended long-term dry storage. A general lack of data and experience modeling the drying process necessitates the testing of advanced concepts focused on the simulation of industrial vacuum drying. Smaller-scale tests that incorporate relevant physics and well-controlled boundary conditions are necessary to provide insight and guidance to the modeling of prototypic systems undergoing drying processes. This report describes the development and testing of waterproof, electrically-heated spent fuel rod simulators as a proof of concept to enable experimental simulation of the entire dewatering and drying process. This report also describes the preliminary development of specially-designed, unheated mock fuel rods for monitoring internal rod pressures and studying water removal from simulated failed fuel rods. A variety of moisture monitoring instrumentation is also being considered and will be downselected for the tracking of dewpoints of gas samples. The effects of cladding oxidation and crud on water retention in dry storage systems can be explored via separate effects tests (SETs) that would measure chemisorbed and physisorbed water content on cladding samples. The concepts listed above will be incorporated into an advanced dry cask simulator with multiple fuel assemblies in order to account for important inter-assembly heat-transfer physics. Plans are described for harvesting up to five full-length 5x5 laterally truncated assemblies from commercial 17x17 PWR skeleton components with the goal of constructing this simulator.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Update on the Thermal Hydraulic Investigations of a Horizontal Dry Cask Simulator

The thermal performance of commercial spent nuclear fuel dry storage casks is evaluated through detailed numerical analysis. These modeling efforts are completed by the vendor to demonstrate performance and regulatory compliance. The calculations are then independently verified by the Nuclear Regulatory Commission (NRC). Canistered dry storage cask systems rely on ventilation between the inner canister and the overpack to convect heat away from the canister to the surrounding environment for both horizontal and vertical configurations. Recent advances in dry storage cask designs have significantly increased the maximum thermal load allowed in a canister in part by increasing the efficiency of internal conduction pathways and by increasing the internal convection through greater canister helium pressure. Carefully measured data sets generated from testing of full-sized casks or smaller cask analogs are widely recognized as vital for validating these models. While several testing programs have been previously conducted, these earlier validation studies did not integrate all the physics or components important in a modern, horizontal dry cask system. The purpose of the present investigation is to produce data sets that can be used to benchmark the codes and best practices presently used to determine cladding temperatures and induced cooling air flows in modern horizontal dry storage systems. The horizontal dry cask simulator (HDCS) has been designed to generate this benchmark data and add to the existing knowledge base. The objective of the HDCS investigation is to capture the dominant physics of a commercial dry storage system in a well-characterized test apparatus for any given set of operational parameters. The close coupling between the thermal response of the canister system and the resulting induced cooling air flow rate is of particular importance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

SNL Contribution: Consequence Analysis for Moisture Remaining in Dry Storage Canisters After Drying

This report discusses several possible sources of water that could persist in SNF dry storage canisters through the drying cycle. In some cases, the water is trapped in occluded geometries in the cask such as dashpots or damaged fuel. Persistence of water or ice in such locations seems unlikely, given the high heat load of the canistered fuel; this is especially true in the case of vacuum drying, where a strong driver exists to remove water vapor from the headspace of such occluded geometries. Water retention in Boral® core material is a known problem, that has in the past resulted in the need for much extended drying times. Since the shift to slightly higher porosity "blister resistant" Boral®, water drainage appears to be less of a problem. However, high surface areas for the Boral® core material will provide a trap for significant amounts of adsorbed water, at least some of which is certain to survive the drying process. Moreover, if corrosion within the cores produces hydrous aluminum corrosion products, these may also survive.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Component Concepts for Advanced Dry Storage Investigations

The purpose of this report is to review technical issues and previous studies relevant to the performance evaluation of dry storage systems during vacuum drying and long-term storage operations and to describe vital experimental components under development that are required for conducting advanced studies. There is a need to validate the extent of water removal in a multi-assembly system using an industrial vacuum-drying procedure, as operational conditions leading to incomplete drying may have potential impacts on the fuel, cladding, and other components in the system. Waterproof, electrically-heated spent fuel rod simulators are under development to enable experimental simulation of the entire de-watering and drying process. Specially-designed, unheated mock fuel rods are used to monitor internal rod pressures and study water removal from simulated failed fuel rods. Furthermore, single assembly studies conducted previously cannot incorporate important inter-assembly heat-transfer physics, so plans for harvesting up to five full-length 5 x 5 truncated assemblies from a single 17 x 17 PWR skeleton are described.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Improved Measurement of Particulate Retention in Simulated Stress Corrosion Cracks

This report documents proposed improvements to an apparatus for measuring flow rates and aerosol retention in stress corrosion cracks (SCCs). The potential for SCCs in canister walls is a concern for dry cask storage systems for spent nuclear fuel. Some of the canisters in these systems are backfilled to significant pressures to promote heat rejection via internal convection. Pressure differentials covering the upper limit of commercially available dry cask storage systems are the focus of the current test assembly. Initial studies will be conducted using engineered microchannels with characteristic dimensions expected in SCCs that hypothetically could form in dry storage canister walls. In a previous study, an apparatus and procedures were developed and implemented to investigate aerosol retention in a simple microchannel with an SCC-like opening of 28.9 gm (0.00110 in.). The width was 12.7 mm (0.500 in.), and the length was 8.86 mm (0.349 in.). These initial results indicated 44% of the aerosols available for transmission were retained upstream of microchannel However, limitations in the aerosol instruments available at the time of the preliminary study introduced known biases into the measurements. While these biases were identified and quantified, their presence introduced unwanted degrees of freedom into the measurements and reduced accuracy. Because these aerosol particle sizers (APS) were limited to sampling at atmospheric pressure, a mass flow controller was used to supply the sample upstream of the crack to the APS. The average line loss across all particle sizes for this mass flow controller was 50%. The sample downstream of the crack was delivered via a mass flow meter and caused a line loss of 20%. Another source of bias was using separate (but identical) instruments to measure the aerosols upstream and downstream of the microchannel, which could register up to 40% different when measuring the same sample stream. The experience of conducting the preliminary study highlighted the need for improvements in the experimental approach that would eliminate these biases and benefit future studies. An aerosol analyzer has been identified and ordered that is ideally suited for this study and should substantially mitigate these biases. Moving forward in the near term, the same simple microchannel will be further investigated using the improved aerosol instrumentation. Additionally, an offset microchannel with a step in the flow path will be designed and fabricated for similar testing. Looking out further, the capability to produce and test laboratory generated SCCs will be developed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗