Search NASA⌕ Search

Engineering topics

Lu, Ming

Publications and source records attributed to Lu, Ming.

At least 19 records

Quadratic magnetoresistance across the insulator–metal transition in V4O7 thin films

We present a comparative magnetotransport study of V4O7 thin films grown simultaneously on single-crystal Al2O3 (r-cut) and amorphous SiO2 substrates, to examine substrate-induced effects on electronic transport across the insulator–metal transition (IMT). Temperature-dependent resistivity reveals a broad electronic ordering regime below the IMT, with both films exhibiting similar transition temperatures but differing by nearly an order of magnitude in absolute resistivity. Despite this strong substrate dependence of the resistivity scale, the magnetoresistance remains predominantly quadratic in magnetic field over wide temperature intervals for both substrates. Analysis of the quadratic magnetoresistance defines an effective mobility scale that evolves systematically across the IMT and exhibits a similar temperature dependence for the two films. Structural characterization, including atomic-resolution scanning transmission electron microscopy of the V4O7/Al2O3 interface and azimuthal X-ray diffraction measurements, reveals a sharp interface and well-defined in-plane crystallographic registry for the r-cut film, in contrast to the rotationally averaged in-plane structure expected for films grown on amorphous SiO2. These results indicate that while substrate-controlled structural registry modifies the resistivity scale, the quadratic magnetotransport response across the IMT remains largely robust, providing a consistent diagnostic of electronic transport in V4O7 thin films.

25 ENERGY STORAGE↗

Vapor‐Phase Infiltrated Organic–Inorganic Positive‐Tone Hybrid Photoresist for Extreme UV Lithography

Abstract Continuing extreme downscaling of semiconductor devices, essential for high performance and energy efficiency of future microelectronics, hinges on extreme ultraviolet lithography (EUVL) and addressing associated challenges. One of such challenges is a need for improved EUV photoresists featuring simultaneously high sensitivity, resolution, and etch selectivity. Here, a new, positive‐tone, organic–inorganic hybrid EUV photoresist is demonstrated that delivers a high‐resolution EUVL and electron‐beam lithography (EBL) patterning capability combined with high sensitivity and etch resistance. The new resist, poly(methyl methacrylate) infiltrated with indium oxide (PMMA‐InO x ), is synthesized via vapor‐phase infiltration (VPI), a material hybridization technique derived from atomic layer deposition. The weak binding of the gaseous indium precursor, trimethylindium, to the carbonyl group in PMMA allows the synthesis of hybrids with inorganic content distributed uniformly in the resist, enabling high EUVL and EBL sensitivities (18 mJ cm −2 and 300 µC cm −2 , respectively) and high‐resolution positive‐tone EUVL patterning (e.g., 40 nm half‐pitch line‐space and 50 nm diameter contact hole patterns) with high Si etch selectivity (>30–40). The low exposure doses required to pattern the PMMA‐InO x hybrid resist, high etch resistance, and processing strategies, which are developed, can pave the way for using infiltration‐synthesized hybrid thin films as reliable positive‐tone EUV photoresists for future semiconductor patterning.

36 MATERIALS SCIENCE↗

Multi-element metasurface system for imaging in the near-infrared

Metasurfaces are optically thin 2D arrays of subwavelength scatterers that modify scalar and vector properties of incident electromagnetic fields. Metasurface lenses are of particular interest for imaging applications for their flat form factor, compatibility with CMOS fabrication processes, and potential for correcting aberrations with a small number of elements. Here, we advance this capability by realizing a millimeter-diameter, polarization-independent metalens triplet system with chromatic aberration correction over the wavelength range of 1.30–1.60 μm and monochromatic aberration correction enabling a field of view of 50°.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Achieving High-Resolution Hard X-ray Microscopy using Monolithic 2D Multilayer Laue Lenses

This article introduces the 2D multilayer Laue lens (MLL) nanofocusing optics recently developed for high-resolution hard X-ray microscopy. The new optics utilized a micro-electro-mechanical-system (MEMS)-based template to accommodate two linear MLL optics in a pre-aligned configuration. Angular misalignment between the two lenses was controlled in tens of millidegrees, and the lateral position error was on a micrometer scale. Using the developed 2D MLLs, an astigmatism-free point focus of approximately 14 nm by 13 nm in horizontal and vertical directions, respectively, at 13.6 keV photon energy was obtained. In conclusion, the success of 2D MLL optics with an approaching 10 nm resolution is a significant step forward for the development of high-resolution hard X-ray microscopy and applications of MLL optics in the hard X-ray community.

36 MATERIALS SCIENCE↗

Machine-learning-based automatic small-angle measurement between planar surfaces in interferometer images: A 2D multilayer Laue lenses case

Here, we report a new machine-learning-based approach to automatically measure the small angle between multiple planar surfaces characterized by white light interferometers. By applying an unsupervised clustering algorithm, DBSCAN (Density-Based Spatial Clustering of Applications with Noise), the multiple surfaces in an interferometer image are automatically identified as distinct surfaces. The angles between every two surfaces are then calculated through the surface fitting. This method can be applied to multiple surfaces regardless of their shapes and locations and significantly simplifies the angle measurement procedure. Using the developed method, we have demonstrated a quick and precise angle measurement for the alignment of 2D Multilayer Laue Lenses (MLLs) for the development of high-resolution x-ray microscopy. This automatic, accurate, and robust small-angle measurement method is compatible with widely used white light interferometers and can be further applied to other metrology applications of interferometer results.

36 MATERIALS SCIENCE↗

Kinetics and evolution of solid-state metal dealloying in thin films with multimodal analysis

Thin-film solid-state metal dealloying (thin-film SSMD) is an emerging technique that uses self-organization to design nanostructured thin films. The resulting 3D bicontinuous nanostructures are promising for a wide range of applications, such as catalysis and energy storage. In this work, we prepared thin films by SSMD using Ti-Cu as the parent alloy and Mg as the solvent. Using a multimodal approach, we combined synchrotron X-ray spectroscopy, diffraction, and high-resolution electron-based spectroscopy and imaging to study their morphological, structural, and chemical evolution. The processing-structure relationship was analyzed as a function of parent alloy composition and dealloying temperature and time. Morphological transitions from globular, to lamellar, to bicontinuous structures, in conjunction with a ligament size evolution, were identified as functions of the parent alloy composition. The dealloying rate increased with increasing concentration of interdiffusing elements (dissolving component) in the parent alloy. The parting limit, a dealloying compositional threshold, was systematically analyzed and determined to be 30%–40%. The order of crystalline phase formation is CuMg 2 , Cu 2 Mg, and Ti; the Ti phase first shows self-reorganization during dealloying, separate from the crystallization process. The coarsening in thin-film SSMD was identified and not entirely self-similar; in addition to the increase of ligament size over time, the formation of larger globular ligaments were also observed. This work furthers our fundamental understanding of thin-film SSMD and nanostructured thin-film design, where the thermodynamic and kinetic effects differ from the bulk counterparts. The fact that dealloying and diffusion outpaces the crystallization and new phase formation also offers opportunities to utilize thin-film SSMD in certain alloy systems in which deleterious intermetallic phases need to be suppressed, that may not be possible in the bulk geometry.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

MgZnO High‐Voltage Transparent Thin‐Film Transistors Built on Glass

Recently, there has been increasing interest in building‐integrated photovoltaic (BIPV), which enables harvesting solar energy effectively. Large‐area glass components such as windows are widely used in modern constructions. In addition to the PV on opaque components such as walls and roofs, the transparent photovoltaic (TPV) directly built on glass is complementary to fully utilize the PV energy in BIPV. A high‐voltage transparent thin‐film transistor (HVTTFT) built on glass is an ideal option for distributed microinverters for TPV modules. A wide‐bandgap oxide‐based HVTTFT on glass for this purpose is reported. The HVTTFT on glass uses ZnO‐based materials with different functions for two roles: a semiconductor Mg 0.01 Zn 0.99 O (MZO) as TFT channel and Al‐doped ZnO (AZO) as transparent conductive oxide (TCO) electrodes. The centrosymmetric circular structure of the MZO HVTTFT with a high‐k‐stacking gate dielectric enables a blocking voltage as high as ≈1 kV and an on/off ratio of 10 6 . The device exhibits an average optical transmittance of 81% over the visible spectrum.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Mechanism of dielectric barrier discharge plasma technology to improve the quantity of short-chain fatty acids in anaerobic fermentation of waste active sludge

The mechanism of improving the anaerobic fermentation performance of waste active sludge by using dielectric barrier discharge (DBD) plasma pretreatment technology was investigated. The maximum accumulation of short-chain fatty acids (SCFAs) was observed on the 7th day of anaerobic fermentation when the DBD power was 76.50 W, which was 1726.70 mg COD/L, 1.50 times of the control group. The ratio of acetic acid in DBD group was 9.30% higher than that in the control. Further mechanism research indicated that DBD pretreatment can destroy the structure of extracellular polymer substances and release organic substances such as protein and polysaccharide. The dissolved organic matter analysis indicated that the DBD technique could increase the release of biodegradable organics (eg., tyrosine proteins, soluble microbial by-products), thus accelerate the biotransformation of organic substance. Bacterial community structure analysis showed that the increase in the abundance of Firmicutes and Bacteroidetes and the decrease in the abundance of Proteobacteria in DBD group were beneficial to the accumulation of SCFAs. Besides, further archaeal analysis indicated that the decrease of Methanosaeta sp. and Methanosarcina sp . abundance in the DBD group facilitate acetic acid accumulation. This study demonstrated that the DBD technique can be used as an effective and potential pretreatment method to improve sludge anaerobic fermentation performance.

Wang, Jie↗

A High-Throughput MEMS-Based Differential Scanning Calorimeter for Direct Thermal Characterization of Antibodies

Calorimeters, which can be used for rapid thermal characterization of biomolecules, are getting intense attention in drug development. This paper presents a novel MEMS-based differential scanning calorimeter (DSC) for direct thermal characterization of protein samples. The DSC consisted of a pair of temperature sensors made by vanadium oxide (VOx) film with a temperature coefficient of resistivity of –0.025/K at 300 K, a microfluidic device with high thermal insulation (2.8 K/mW), and a Peltier heater for linear temperature scanning. The DSC exhibited high sensitivity (6.1 µV/µW), low noise (0.4 µW), high scanning rate (45 K/min), and low sample consumption volume (0.63 µL). The MEMS DSC was verified by measuring the temperature-induced denaturation of lysozyme at different pH, and then used to study the thermal stability of a monoclonal antibody (mAb), an antigen-binding fragment (Fab), and a dual variable domain immunoglobulin (DVD-Ig) at pH = 6. The results showed that lysozyme is a stable protein in the pH range of 4.0–8.0. The protein stability study revealed that the transition temperatures of the intact Fab fragment, mAb, and DVD proteins were comparable with conformational stability results obtained using conventional commercial DSC. These studies demonstrated that the MEMS DSC is an effective tool for directly understanding the thermal stability of antibodies in a high-throughput and low-cost manner compared to conventional calorimeters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design nanoporous metal thin films via solid state interfacial dealloying

Thin-film solid-state interfacial dealloying (thin-film SSID) is an emerging technique to design nanoarchitecture thin films. The resulting controllable 3D bicontinuous nanostructure is promising for a range of applications including catalysis, sensing, and energy storage. Using a multiscale microscopy approach, we combine X-ray and electron nano-tomography to demonstrate that besides dense bicontinuous nanocomposites, thin-film SSID can create a very fine (5–15 nm) nanoporous structure. Not only is such a fine feature among one of the finest fabrications by metal-agent dealloying, but a multilayer thin-film design enables creating nanoporous films on a wider range of substrates for functional applications. Through multimodal synchrotron diffraction and spectroscopy analysis with which the materials’ chemical and structural evolution in this novel approach is characterized in details, we further deduce that the contribution of change in entropy should be considered to explain the phase evolution in metal-agent dealloying, in addition to the commonly used enthalpy term in prior studies. Here, the discussion is an important step leading towards better explaining the underlying design principles for controllable 3D nanoarchitecture, as well as exploring a wider range of elemental and substrate selections for new applications.

36 MATERIALS SCIENCE↗

Design, modeling and experimental validation of a micro cantilever beam with an electro-controllable twisting ability

The structure design of micro cantilever beams (MCBs), which has a significant effect on MCBs' controllable actuation range, is usually restricted by the establishment of the inner electric circuit. This paper proposes the design of a micro electro-controllable twisting cantilever beam (METCB). The architecture and the fabrication diagram of the proposed METCB are presented before its features are theoretically and experimentally validated. In detail, the analytical validation includes a sequence of two models: electro-thermal and thermo-mechanical. Through these two models, the thermal distribution along the METCB and the deformation brought by the thermal distribution are investigated, respectively. On the basis of the design and equations, the METCB samples have been manufactured using a planar deposition technique with an e-beam evaporator. Two in-site experiments are then conducted to sequentially figure out the upper voltage limit of the inner electric circuit and the maximum temperature limit of the METCB. Finally, another experiment is carried out to explore the relation between the applied voltage and the relative twisting angle of the METCB sample. Here, the theoretical prediction and the observed experiment result both prove the feasibility of the proposed METCB and its electro-controllable twisting ability.

36 MATERIALS SCIENCE↗

Negative Capacitance MgZnO-Channel Thin-Film Transistor With Ferroelectric NiMgZnO in the Gate Stack

We demonstrate the negative capacitance thin-film transistor (NC-TFT) on glass substrate using the multifunctional MgZnO (MZO). The Mg 0.03 Zn 0.97 O semiconductor layer acts as the TFT channel for stable operation while the Ni-doped MZO, i.e. Ni 0.02 Mg 0.15 Zn 0.83 O (NMZO) serves as the ferroelectric layer in the NMZO/SiO 2 stacking gate dielectric structure. The subthreshold swing (SS) value is significantly reduced over the reference TFT without ferroelectric layer. The minimum SS value of the NC-TFT reaches 52 mV/dec while the on/off ratio of drain current ID reaches 10 9 .

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Luminescence mechanism in hydrogenated silicon quantum dots with a single oxygen ligand

Though photoluminescence (PL) of Si quantum dots (QDs) has been known for decades and both theoretical and experimental studies have been extensive, their luminescence mechanism has not been elaborated. Several models have been proposed to explain the mechanism. A deep insight into the origin of light emissions in Si QDs is necessary. This work calculated the ground- and excited state properties of hydrogenated Si QDs with various diameters, including full hydrogen passivation, single Si=O ligands, single epoxide and coexisting Si=O and epoxide structures in order to investigate the dominant contribution states for luminescence. The results revealed that even a single oxygen atom in hydrogenated Si QDs can dramatically change their electronic and optical properties. Intriguingly, we found that a size-independent emission, the strongest among all possible emissions, was induced by the single Si=O passivated Si-QDs. In non-oxidized Si-QDs exhibiting a core-related size-tunable emission, the luminescence properties can be modulated by the ligands of Si QDs, and a very small number of oxygen ligands can strongly influence the luminescence of nanocrystalline silicon. Our findings deepen the understanding of the PL mechanism of Si QDs and can further promote the development of silicon-based optoelectronic devices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗