Search NASA⌕ Search

Engineering topics

Lu, Ming

Publications and source records attributed to Lu, Ming.

At least 37 records · Page 2

Mid-infrared frequency doubling using strip-loaded silicon nitride on epitaxial barium titanate thin film waveguides

Broadband mid-infrared (mid-IR) frequency doubling was demonstrated using nonlinear barium titanate (BTO) thin films. The device has a strip-loaded waveguide structure consisting of top silicon nitride (SiN) strips and an underneath BTO guiding layer. The epitaxial BTO was deposited on a strontium titanate (STO) substrate by pulsed-laser deposition. Through a SiN grating coupler, the pumping mid-IR light at wavelength &#x03BB;<!-- λ --> = 3.30 &#x2212;<!-- - --> 3.45 &#x00B5;<!-- µ --> m was coupled into the nonlinear BTO layer, where the spectrum of the near-infrared (NIR) second-harmonic generation was characterized. The developed BTO waveguides provide a platform for mid-IR nonlinear integrated photonics and on-chip quantum optics.

42 ENGINEERING↗

Multilayered microstructures with shape memory effects for vertical deployment

This paper presents a fabrication and characterization of multilayered microstructures with shape memory effects enabling large vertical deployment under electro-thermal actuation. Our previous research demonstrated vertical deployment of such microstructures by the effect of thermal mismatch. Development of equiatomic NiTi layers in the multilayered microstructure is investigated further for shape memory effects. Multilayered microstructures are built by sputtered NiTi layers and a lift-off process. Negative photoresist ma-N1420 enables clean lift-off of 500 nm thick NiTi layers by forming a significant undercut profile after development. The parametric study on co-sputter powers for Ti and Ni 50 Ti 50 targets suggests that 100 W RF on Ti target and 200 W DC on Ni 50 Ti 50 target can deposit Ni 49.62 Ti 50.38 layers. X-Ray Diffraction (XRD) and Atomic Force Microscopy (AFM) were used to study the crystal structures and surface topography of NiTi layers. XRD results of post-annealed Ni 49.62 Ti 50.38 layers show coexistence of austenite and martensitic phases at room temperature, suggesting that the transformation temperature of such NiTi layers should be approximate 20 °C. The surface topography of Ni 49.62 Ti 50.38 layers reveals substantial increase of surface roughness at ambient conditions after the annealing. Experimental verification of the multilayered microstructure for vertical deployment was carried out by Signatone Probe Station and Dual Scanning Electron Microscope/Focused Ion Beam (SEM/FIB) system. Finally, a vertical deployment of the two-dimensional (2D) multilayered microstructures for three-dimensional (3D) can be detected by applying a constant voltage of 0.04 V, and the expected 3D deployment displacement is enlarged from 2 μm to 10 μm by introducing the shape memory effect.

42 ENGINEERING↗

Thermo-mechanical modeling and experimental validation for multilayered metallic microstructures

This paper presents thermo-mechanical modeling on multilayered metallic microstructures consisting of two bilayers that enable 3D deployment once being Joule heated. Additionally, a representative design of such microstructures, as well as their working principle is introduced. Furthermore, a mathematical model is derived using Euler–Bernoulli beam theory, and analytical solutions describing out-of-plane displacement of the multilayered microstructures when uniformly heated, which is validated by finite element analysis. Parametric analysis on thermal load and dimensional change of beam shows a good agreement between the analytical solutions and results given by finite element analysis. The phases of the near-equiatomic NiTi layer are analyzed by EDS and XRD, which prove to be austenite during the Joule heating process. The mechanical properties of austenite NiTi are incorporated into the analytical solutions that provides a good estimation of 3D deployment of microstructures made of NiTi and aluminum. The experimental results provide an approximately 7 µm out-of-plane deployment by applying a uniform temperature increase of 132 K, and parametric analysis on the dimension of top aluminum beam offers another promising approach to larger 3D deployment. The proposed mathematical model provides an efficient tool for predicting the out-of-plane deployment of such multilayered microstructures.

36 MATERIALS SCIENCE↗

Effects of deposition and annealing conditions on the crystallisation of NiTi thin films by e-beam evaporation

This Letter demonstrates the effects of deposition and annealing conditions on the crystallisation of nickel–titanium (NiTi) thin films deposited by the e-beam evaporation. NiTi thin films of 0.5 μm thick are fabricated on P-type (110) silicon substrates using the e-beam evaporation technique. We find that with the characterisations using the X-ray diffraction method, the results indicate that low e-beam deposition rate and argon employed annealing procedures can be beneficial to the formation of NiTi crystalline structure. Additionally, the as-deposited NiTi thin films without annealing procedures are amorphous, when deposited on the substrates at low temperatures. The differential scanning calorimetry studies show NiTi thin films formed by the e-beam evaporation are Ni-rich. Furthermore, SEM images illustrate that high-precision patterned NiTi thin film microstructures can be fabricated by combining with the e-beam evaporation and lift-off resist methods, without any wet or dry etching procedures. The proposed fabrication process for NiTi thin film microstructures shows great potential for application in shape memory alloy medical devices, as well as the micro-robotics.

36 MATERIALS SCIENCE↗

A Chip-Scale Oscillation-Mode Optomechanical Inertial Sensor Near the Thermodynamical Limits

Modern navigation systems integrate the global positioning system (GPS) with an inertial navigation system (INS), which complement each other for correct attitude and velocity determination. Here, the core of the INS integrates accelerometers and gyroscopes used to measure forces and angular rate in the vehicular inertial reference frame. With the help of gyroscopes and by integrating the acceleration to compute velocity and distance, precision and compact accelerometers with sufficient accuracy can provide small–error location determination. Solid–state implementations, through coherent readout, can provide a platform for high performance acceleration detection. In contrast to prior accelerometers using piezoelectric or capacitive readout techniques, optical readout provides narrow–linewidth high–sensitivity laser detection along with low–noise resonant optomechanical transduction near the thermodynamical limits. Here an optomechanical inertial sensor with an 8.2 µg Hz –1/2 velocity random walk (VRW) at an acquisition rate of 100 Hz and 50.9 µg bias instability is demonstrated, suitable for applications, such as, inertial navigation, inclination sensing, platform stabilization, and/or wearable device motion detection. Driven into optomechanical sustained–oscillation, the slot photonic crystal cavity provides radio–frequency readout of the optically–driven transduction with an enhanced 625 µg Hz –1 sensitivity. Measuring the optomechanically–stiffened oscillation shift, instead of the optical transmission shift, provides a 220× VRW enhancement over pre–oscillation mode detection.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Infiltration synthesis of hybrid nanocomposite resists for advanced nanolithography

In this work, we demonstrate a simple ex-situ inorganic infiltration route for transforming standard organic resists into highperformance positive tone hybrid resist platform. A model thin film PMMA-AlOx hybrid resist system has been synthesized by hybridization of PMMA with AlOx and investigated for electron beam lithography. The approach possesses full controllability of the resist performance in terms of critical does, patterning contrast reaching up to 30 and etch resistance for plasma-based pattern transfer processes. The high selectivity Si etching capability demonstrated using a lowtemperature cryo-Si etch process, based on the controlled infiltration outperforms commercial resists and typical hard mask material thermal SiO 2 , with estimated achievable selectivity in excess of ~300. Si nanostructures down to ~30 nm with aspect ratio up to ~17 are also transferred into the Si substrate. Easy implementation and adaptability for different inorganic infiltrations, this platform is well capable of potentially delivering the resist performance and throughput necessary for EUV lithography.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Dielectric metasurfaces for complete and independent control of the optical amplitude and phase

Metasurfaces are optically thin metamaterials that promise complete control of the wavefront of light but are primarily used to control only the phase of light. Here, we present an approach, simple in concept and in practice, that uses meta-atoms with a varying degree of form birefringence and rotation angles to create high-efficiency dielectric metasurfaces that control both the optical amplitude and phase at one or two frequencies. This opens up applications in computer-generated holography, allowing faithful reproduction of both the phase and amplitude of a target holographic scene without the iterative algorithms required in phase-only holography. We demonstrate all-dielectric metasurface holograms with independent and complete control of the amplitude and phase at up to two optical frequencies simultaneously to generate two- and three-dimensional holographic objects. We show that phase-amplitude metasurfaces enable a few features not attainable in phase-only holography; these include creating artifact-free two-dimensional holographic images, encoding phase and amplitude profiles separately at the object plane, encoding intensity profiles at the metasurface and object planes separately, and controlling the surface textures of three-dimensional holographic objects.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Adult height, body mass index change, and body shape change in relation to esophageal squamous cell carcinoma risk: A population‐based case‐control study in China

Abstract The relationship between risk of esophageal squamous cell carcinoma (ESCC) and adult height, changes in individual body mass index (BMI) and body shape is not established. We performed a large population‐based case‐control study, which enrolled a total of 1414 ESCC cases and 1989 controls in a high‐incidence area in China. Using face‐to‐face interview with a structured questionnaire, information on participants' heights, weights, and perceived body shapes at 20 years of age was collected. Additionally, data on weight and perceived body shape among the same participants 10 years prior to ascertainment were collected using the same method. Odd ratios (ORs) of ESCC risk in relation to BMI and body shape were estimated using unconditional logistic regression models. The adjusted results indicated that ESCC risk in adults rapidly rose as height increased, plateauing at 170 cm among men and 157 cm among women. Among participants who were underweight, normal weight, or thinner than body shape 4, body weight loss was associated with increased risk of ESCC, and body weight gain was associated with decreased incidence of ESCC (ORs ranging from 0.40 to 0.76). Notably, however, changes in body weight did not significantly affect ESCC risk among participants who were overweight, obese, or larger than body shape 3. Maintaining a fit body shape and a reasonable BMI is advisable and of vital importance to reduce the risk of ESCC, especially in high‐risk areas.

Yang, Xiaorong↗

Patterning Si at the 1 nm Length Scale with Aberration-Corrected Electron-Beam Lithography: Tuning of Plasmonic Properties by Design

Patterning of materials at single nanometer resolution allows engineering of quantum confinement effects, as these effects are significant at these length scales, and yields direct control over electro-optical properties. Silicon is by far the most important material in electronics, and the ability to fabricate Si-based devices of the smallest dimensions for novel device engineering is highly desirable. Here, the work presented here uses aberration-corrected electron-beam lithography combined with dry reactive ion etching to achieve both: patterning of 1-nm features and surface and volume plasmon engineering in Si. The nanofabrication technique employed here produces nanowires with a line edge roughness (LER) of 1 nm (3σ). In addition, this work demonstrates tuning of the Si volume plasmon energy by 1.2 eV from the bulk value, which is one order of magnitude higher than previous attempts of volume plasmon engineering using lithographic methods.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Advancing next generation nanolithography with infiltration synthesis of hybrid nanocomposite resists

Organic–inorganic hybrid resists are emerging as an effective way of addressing stringent process requirements for aggressive down-scaling of semiconducting devices. Yet, hybrid resists generally require complex chemical synthesis while being predominantly negative-tone with high dose requirements. For positive-tone processes and high-aspect-ratio pattern transfers, resist choices are limited to costly, non-hybrid alternatives, whose etch resistance is still inferior compared with hybrid resists. In this work, we demonstrate a novel hybrid positive-tone resist platform utilizing simple ex situ vapor-phase inorganic infiltration into standard resist materials. A model system based on poly(methyl methacrylate) (PMMA) thin film hybridized with aluminum oxide has been demonstrated for electron-beam lithography patterning, featuring a fully controllable critical exposure dose, contrast, and etch resistance. The hybrid resist not only achieves contrast as high as ~30, six-fold enhancement over standard PMMA, but also enables Si nanostructures with resolution down to ~30 nm and an aspect ratio as high as ~17, owing to enhancement of the Si etch selectivity to ~70, with an estimated achievable maximum of ~300, far exceeding known commercial positive-tone resist systems. The easy implementabilility, combined with versatile ex situ control of resist characteristics, makes this hybrid resist synthesis method uniquely suited for addressing the resist performance and high throughput required for advanced nanolithography techniques, such as extreme ultraviolet lithography, possibly.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Guiding light in bent waveguide superlattices with low crosstalk

Waveguide superlattices with a subwavelength pitch and low crosstalk can significantly increase the waveguide integration density and are beneficial for many chip-scale applications. Bending of such high-density waveguide superlattices is necessary for flexible signal routing. However, tight bending tends to induce high crosstalk between guided modes, as witnessed in multimode waveguide bends. Here we explore the mechanisms of light guiding and coupling in a subwavelength-pitch waveguide superlattice bend and analyze how bending further modifies the already “renormalized” parameters of superlattice modes via various physical effects. Particularly, bending can skew the phase mismatch in a waveguide superlattice, sometimes producing a near phase-matching condition and causing salient crosstalk spikes among non-first-nearest neighbors. Interestingly, a waveguide superlattice with less pristine phase mismatch may be more robust against such skew of phase mismatch and can suppress crosstalk spikes by ~10 dB. Bending with 5–15 μm radii and subwavelength pitches has been demonstrated with crosstalk lower than -19.5 dB. The scaling of the footprint of waveguide superlattice bending is analyzed, and significant footprint reduction can be achieved for chip-scale applications. The rationale for footprint reduction of superlattice bending under crosstalk constraint differs markedly from that of a single waveguide bend.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Thermodynamic analysis of a MEMS based differential scanning calorimeter model

Thin film based differential scanning calorimeter (DSC) was developed and utilized for the study of phase-transition kinetics in protein samples. In this paper, we proposed a MEMS based DSC model. The distance between the sample and reference cell was optimized based on the thermal analysis result. The influence of the response time to the shape of the DSC thermograms and the transition temperature was also studied systematically. Meanwhile, Lumry-Eyring model was used to investigate the relationship between the scanning rate and the transition temperature. The modeling result was verified by the lysozyme denaturation tests. This study provided a pathway for the optimization of MEMS based DSC array and the correction of the DSC thermograms.

47 OTHER INSTRUMENTATION↗

Resolving 500 nm axial separation by multi-slice X-ray ptychography

Multi-slice X-ray ptychography offers an approach to achieve images with a nanometre-scale resolution from samples with thicknesses larger than the depth of field of the imaging system by modeling a thick sample as a set of thin slices and accounting for the wavefront propagation effects within the specimen. Here, we present an experimental demonstration that resolves two layers of nanostructures separated by 500 nm along the axial direction, with sub-10 nm and sub-20 nm resolutions on two layers, respectively. Fluorescence maps are simultaneously measured in the multi-modality imaging scheme to assist in decoupling the mixture of low-spatial-frequency features across different slices. The enhanced axial sectioning capability using correlative signals obtained from multi-modality measurements demonstrates the great potential of the multi-slice ptychography method for investigating specimens with extended dimensions in 3D with high resolution.

36 MATERIALS SCIENCE↗

Hybrid Metasurface-Based Mid-Infrared Biosensor for Simultaneous Quantification and Identification of Monolayer Protein

Metasurfaces emerge as a promising photonic platform for biosensing because they offer strong optical confinement and tunable optical resonances. Here, we show that metasurface-based biosensors consisting of gold nanoantenna arrays loaded with graphene and working in the mid-infrared (mid-IR) spectral range can achieve simultaneous high-sensitivity and high-specificity detection of biomolecules. Strong light–molecule interactions in deeply subwavelength optical spots created by the biosensors allow us to determine the concentration of protein molecules via spectral shifts of the metasurface resonance. A combination of passive and active tuning of the metasurface sensors allows us to spectrally overlap the metasurface resonance and the protein vibrational modes, so that protein molecules can be identified via their characteristic mid-IR “fingerprints”. As a result, the high sensitivity and specificity of the metasurface sensors enable us to determine the secondary structure of protein immunoglobulin (IgG) molecules 4 orders of magnitude more sensitive than attenuated total reflection Fourier transform infrared spectroscopy.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Indium Tin Oxide Broadband Metasurface Absorber

Metamaterials have been designed to achieve a wide range of functionalities. Metamaterial absorbers are of particular interest for various applications such as infrared detectors, emissivity coatings, and photovoltaic cells. Various metamaterial platforms have been demonstrated to achieve perfect absorption and several attempts have been made to extend the absorption bandwidth of such devices. We demonstrate a broadband infrared absorber using an asymmetric Fabry–Perot cavity consisting of a monolithically fabricated two-layer metasurface. Superoctave optical absorption is achieved by tailoring the structure of the metasurface layers and the thickness of the cavity. Furthermore, the device yields absorptance of over 80% from λ = 4–16 μm, while maintaining the performance over a wide range of incident angles. In contrast to most metamaterial absorbers, our metasurface layers are made of customized indium tin oxide (ITO), conferring the advantage of CMOS compatibility compared to previous approaches using noble metals.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Nanostructured fibers as a versatile photonic platform: radiative cooling and waveguiding through transverse Anderson localization

Broadband high reflectance in nature is often the result of randomly, three-dimensionally structured materials. This study explores unique optical properties associated with one-dimensional nanostructures discovered in silk cocoon fibers of the comet moth, Argema mittrei. The fibers are populated with a high density of air voids randomly distributed across the fiber cross-section but are invariant along the fiber. These filamentary air voids strongly scatter light in the solar spectrum. A single silk fiber measuring ~50 μm thick can reflect 66% of incoming solar radiation, and this, together with the fibers’ high emissivity of 0.88 in the mid-infrared range, allows the cocoon to act as an efficient radiative-cooling device. Drawing inspiration from these natural radiative-cooling fibers, biomimetic nanostructured fibers based on both regenerated silk fibroin and polyvinylidene difluoride are fabricated through wet spinning. Optical characterization shows that these fibers exhibit exceptional optical properties for radiative-cooling applications: nanostructured regenerated silk fibers provide a solar reflectivity of 0.73 and a thermal emissivity of 0.90, and nanostructured polyvinylidene difluoride fibers provide a solar reflectivity of 0.93 and a thermal emissivity of 0.91. The filamentary air voids lead to highly directional scattering, giving the fibers a highly reflective sheen, but more interestingly, they enable guided optical modes to propagate along the fibers through transverse Anderson localization. This discovery opens up the possibility of using wild silkmoth fibers as a biocompatible and bioresorbable material for optical signal and image transport.

36 MATERIALS SCIENCE↗