Engineering topics
Publications and source records attributed to Lu, Ping.
Metamaterials present great potential in the applications of solar cells and nanophotonics, such as super lenses and other meta devices, owing to their superior optical properties.
This paper presents a novel probabilistic machine learning (PML) framework to estimate the Brillouin frequency shift (BFS) from both Brillouin gain and phase spectra of a vector Brillouin optical time-domain analysis (VBOTDA). The PML framework is used to predict the Brillouin frequency shift (BFS) along the fiber and to assess its predictive uncertainty. We compare the predictions obtained from the proposed PML model with a conventional curve fitting method and evaluate the BFS uncertainty and data processing time for both methods. The proposed method is demonstrated using two BOTDA systems: (i) a BOTDA system with a 10 km sensing fiber and (ii) a vector BOTDA with a 25 km sensing fiber. The PML framework provides a pathway to enhance the VBOTDA system performance.
Not Available
Abstract Metamaterials have gained great research interest in recent years owing to their potential for property tunability, multifunctionality, and property coupling. As a new group of self‐assembled thin films, vertically aligned nanocomposite (VAN)‐based hybrid metamaterials have been demonstrated with significant anisotropic physical properties and a broad range of property tailorability, such as optical anisotropy, magnetic anisotropy, hyperbolic dispersion, and enhanced second harmonic generation properties. Herein, self‐assembled ZrO 2 ‐Co nanocomposite films, with high epitaxial quality and ultra‐fine vertically aligned Co nanopillars (with an average diameter of ≈2 nm) embedded in a ZrO 2 matrix, are fabricated using a pulsed laser deposition (PLD) method. The Co pillar density can be effectively tuned by varying the Co concentration in the target, which results in tunable optical properties and magnetic properties. Specifically, a high saturation magnetization of 100 emu cm −3 , strong out‐of‐plane magnetic anisotropy and tailorable magnetization properties are achieved via tuning the Co nanopillar density. Coupled with hyperbolic dispersion of dielectric constant from 950 to 1500 nm in wavelength, plasmonic Co metal nanopillars, and the unique dielectric ZrO 2 matrix, this new nanoscale hybrid metamaterial shows great potential for future integrated optical and magnetic device designs.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Three metastable compounds predicted to be kinetically stable using an “island” approach were successfully synthesized from designed modulated elemental reactants. Fe0.8V0.2Se2 was synthesized by depositing ultrathin elemental layers in a V|Fe|Se sequence to control the local composition. An alloyed rock salt structured Pb3Mn2Se5 constituent layer, which does not exist as a bulk compound, was synthesized in the heterostructure (Pb3Mn2Se5)0.6VSe2 by depositing a precursor with a V|Se|Pb|Se|Mn|Se|Pb|Se|Mn|Se|Pb|Se sequence of elemental layers that mimicked the compositional profile of the targeted heterostructure. The heterostructure (PbSe)1+δ(FeSe2)2 was prepared by depositing a precursor with a repeating layering sequence of Fe|Pb|Fe|Se, where each sequence contains the number of atoms required to form a single unit cell. In all three systems, the local compositions in the layer sequence kinetically favored the nucleation and growth of the targeted products during the deposition. The diffusion lengths to form the targeted compounds were short, and the diffusion was limited by postdeposition low temperature annealing to favor the growth of the targeted compounds and avoid the decomposition into a mixture of thermodynamically stable compounds.
Transition metal nitrides (e.g., TiN) have shown tremendous promise in optical metamaterials for nanophotonic devices due to their plasmonic properties comparable to noble metals and superior high temperature stability. Vertically aligned nanocomposites (VANs) offer a great platform for combining two dissimilar functional materials with a one-step deposition technique toward multifunctionality integration and strong structural/property anisotropy. Here, we report a two-phase nanocomposite design combining ferromagnetic CoFe 2 nanosheets in the plasmonic TiN matrix as a new hybrid plasmonic metamaterial. The hybrid metamaterials exhibit anisotropic optical and magnetic responses, as well as a pronounced magneto-optical coupling response evidenced by Magneto-optic Kerr Effect measurement, owing to the novel vertically aligned structure. This work demonstrates a new TiN-based metamaterial with anisotropic properties and multifunctionality toward light polarization modulation, optical switching, and integrated optics.
VO 2 has shown great promise for sensors, smart windows, and energy storage devices, because of its drastic semiconductor-to-metal transition (SMT) near 340 K coupled with a structural transition. To push its application toward room-temperature, effective transition temperature (T c ) tuning in VO 2 is desired. Here, in this study, tailorable SMT characteristics in VO 2 films have been achieved by the electrochemical intercalation of foreign ions (e.g., Li ions). By controlling the relative potential with respect to Li/Li + during the intercalation process, T c of VO 2 can be effectively and systematically tuned in the window from 326.7 to 340.8 K. The effective T c tuning could be attributed to the observed strain and lattice distortion and the change of the charge carrier density in VO 2 introduced by the intercalation process. This demonstration opens up a new approach in tuning the VO 2 phase transition toward room-temperature device applications and enables future real-time phase change property tuning.
Calcite (CaCO 3 ) composition and properties are defined by the chemical environment in which CaCO 3 forms. However, a complete understanding of the relationship between aqueous chemistry during calcite precipitation and resulting chemical and physical CaCO 3 properties remains elusive; therefore, we present an investigation into the coupled effects of divalent cations Sr 2+ and Mg 2+ on CaCO 3 precipitation and subsequent crystal growth. Through chemical analysis of the aqueous phases and microscopy of the resulting calcite phases in compliment with density functional theory calculations, we elucidate the relationship between crystal growth and the resulting composition (elemental and isotopic) of calcite. The results of this experimental and modeling work suggest that Mg 2+ and Sr 2+ have cation-specific impacts that inhibit calcite crystal growth, including: (1) Sr 2+ incorporates more readily into calcite than Mg 2+ (D Sr > D Mg ), and increasing [Sr 2+ ] t or [Mg 2+ ] t increases D Sr ; (2) the inclusion of Mg 2+ into structure leads to a reduction in the calcite unit cell volume, whereas Sr 2+ leads to an expansion; (3) the inclusion of both Mg 2+ and Sr 2+ results in a distribution of unit cell impacts based on the relative positions of the Sr 2+ and Mg 2+ in the lattice. These experiments were conducted at saturation indices of CaCO 3 of ~4.1, favoring rapid precipitation. This rapid precipitation resulted in observed Sr isotope fractionation confirming Sr isotopic fractionation is dependent upon the precipitation rate. We further note that the precipitation and growth of calcite favors the incorporation of the lighter 86 Sr isotope over the heavier 87 Sr isotope, regardless of the initial solution conditions, and the degree of fractionation increases with D Sr . In sum, these results demonstrate the impact of solution environment to influence the incorporation behavior and crystal growth behavior of calcite. These factors are important to understand in order to effectively use geochemical signatures resulting from calcite precipitation or dissolution to gain specific information.
Materials are needed that can tolerate increasingly harsh environments, especially ones that retain high strength at extreme temperatures. Higher melting temperature alloys, like those consisting primarily of refractory elements, can greatly increase the efficiency of turbomachinery used in grid electricity production worldwide. Existing alloys, including Ni- and Co-based superalloys, used in components like turbine blades, bearings, and seals, remain a performance limiting factor due to their propensity, despite extensive optimization efforts, for softening and diffusion-driven elongation at temperatures often well above half their melting point. To address this critical materials challenge, we present results from integrating additive manufacturing and alloy design to guide significant improvements in performance via traditionally difficult-to-manufacture refractory alloys. We present an example of a multi-principal element alloy (MPEA), consisting of five refractory elements and aluminum, that exhibited high hardness and specific strength surpassing other known alloys, including superalloys. The alloy shows negligible softening up to 800°C and consists of four compositionally distinct phases, in distinction to previous work on MPEAs. Density functional theory calculations reveal a thermodynamic explanation for the observed temperature-independent hardness and favorability for the formation of this multiplicity of phases.
Abstract not provided.
Multiple techniques are combined to determine the amount of intercalation and/or substitution in transition-metal dichalcogenides. Kiessig fringes in the X-ray reflectivity pattern are used to calculate thickness. Laue oscillations in the specular diffraction pattern of the crystallographically aligned samples determine the number of unit cells in the coherently diffracting domains. The amount of impurity phase(s) is estimated by the difference between the thickness of the films and the size of the domains. If the difference is small relative to the total film thickness, the composition of the crystalline phase can be determined from X-ray fluorescence measurements. The number of unit cells possible can be calculated from the amount of each element determined by X-ray fluorescence measurements using in-plane lattice parameters, and the amount of the anion should agree with the number of unit cells determined from the Laue oscillations. The total amount of the metal relative to that required for the number of unit cells from the Laue oscillations provides a direct determination of the relative amount of intercalation and/or substitution in the crystalline dichalcogenide. So the utility of this approach is illustrated in Fe x V 1–y Se 2 samples. The relative amount of intercalation versus substitution was determined independently using electron microscopy and Rietveld refinement of diffraction patterns and is consistent with this new approach.
Pittsburgh Quantum Institute 2022, Pittsburgh, PA, September 13-15, 2022
Pittsburgh Quantum Institute 2022, Pittsburgh, PA, September 13-15, 2022
Hole spins in Ge quantum wells have shown success in both spintronic and quantum applications, thereby increasing the demand for high-quality material. We performed material analysis and device characterization of commercially grown shallow and undoped Ge/SiGe quantum well heterostructures on 8-in. (100) Si wafers. Material analysis reveals the high crystalline quality, sharp interfaces, and uniformity of the material. We demonstrate a high mobility (1.7 × 10 5 cm 2 V –1 s –1 ) 2D hole gas in a device with a conduction threshold density of 9.2 × 10 10 cm –2 . We study the use of surface preparation as a tool to control barrier thickness, density, mobility, and interface trap density. We report interface trap densities of 6 × 10 12 eV –1 . Our results validate the material’s high quality and show that further investigation into improving device performance is needed. We conclude that surface preparations which include weak Ge etchants, such as dilute H 2 O 2 , can be used for postgrowth control of quantum well depth in Ge-rich SiGe while still providing a relatively smooth oxide–semiconductor interface. Our results show that interface state density is mostly independent of our surface preparations, thereby implying that a Si cap layer is not necessary for device performance. Transport in our devices is instead limited by the quantum well depth. Commercially sourced Ge/SiGe, such as studied here, will provide accessibility for future investigations.
The Hong–Ou–Mandel (HOM) effect is a fascinating quantum phenomenon that defies classical explanation. Traditionally, remote nonlinear sources have been used to achieve coincident photons at the HOM beam splitter. Here, we suggest that the coincident emission source required for HOM interference can be created locally using superradiant near field coupled emitters positioned across the beam splitter gap. We show that sensitivity to permittivity changes in the beam splitter gap, and corresponding Fisher information can be substantially enhanced with HOM photon detection. Subsequently, we outline several strategies for integration of superradiant emitters with practical sensor systems. Taken together, these findings should pave a way for a wide array of near field HOM quantum sensors and novel quantum devices.