Engineering topics

Mane, Anil U.

Publications and source records attributed to Mane, Anil U..

58 records · Page 4

DOE OSTI2020

Visible-Light-Activated Photocatalytic Films toward Self-Cleaning Membranes

Membranes are among the most promising means of delivering increased supplies of fit-for-purpose water, but membrane fouling remains a critical issue restricting their widespread application. Coupling photocatalysis with membrane separation has been proposed as a potentially effective approach to reduce membrane fouling. However, commonly used materials in photocatalysis limit use of low-cost sources such as sunlight due to their large band gaps. There are few examples of in situ photocatalytic self-cleaning of membranes, with removal from the filtration system and ex situ illumination being more common. In this study, a visible-light-activated photocatalytic film prepared by nitrogen doping into the lattice of TiO 2 was deposited on commercial ceramic membranes via atomic layer deposition (ALD). The synergy between membrane separation and redox reactions between organic pollutants and reactive oxygen species (ROS) produced by the visible-light-activated layer offers a possibility for stable and sustainable membrane operation under in situ solar irradiation.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Atomic layer deposition of HfO 2 films using carbon-free tetrakis(tetrahydroborato)hafnium and water

Thin hafnium oxide films were prepared by atomic layer deposition using a carbon-free precursor, tetrakis(tetrahydroborato)hafnium [Hf(BH 4 )( 4 )], and H 2 O. Film growth was studied using an in situ quartz crystal microbalance and Fourier transform infrared spectroscopy measurements. Self-limiting growth was observed between 100 and 175 degrees C, but the thermal decomposition of the Hf precursor occurred at higher temperatures. The film properties were investigated using x-ray photoelectron spectroscopy, x-ray reflectivity, x-ray diffraction, ellipsometry, time-of-flight secondary ion mass spectrometry, and x-ray absorption spectroscopy. The as-deposited films were found to consist of an amorphous mixture of HfO 2 and B 2 O 3 , and had a lower density and lower refractive index compared to pure HfO 2 thin films. Finally, annealing the films to >750 degrees C yielded crystalline monoclinic HfO 2 with a density of 9g/cm 3 and a refractive index of 2.10.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Polyphenol-Sensitized Atomic Layer Deposition for Membrane Interface Hydrophilization

Improvements in energy-water systems will necessitate fabrication of high-performance separation membranes. To this end, interface engineering is a powerful tool for tailoring properties, and atomic layer deposition (ALD) has recently emerged as a promising and versatile approach. However, most non-polar polymeric membranes are not amenable to ALD processing due to the absence of nucleation sites. Here, a sensitization strategy for ALD-coating is presented, illustrated by membrane interface hydrophilization. Facile dip-coating with polyphenols effectively sensitizes hydrophobic polymer membranes to TiO2 ALD coating. Tannic acid-sensitized ALD-coated membranes exhibit outstanding underwater crude oil repulsion and rigorous mechanical stability through bending and rinsing tests. As a result, these membranes demonstrate outstanding crude oil-in-water separation and reusability compared to untreated membranes or those treated with ALD without polyphenol pretreatment. A possible polyphenol-sensitized ALD mechanism is proposed involving initial island nucleation followed by film intergrowth. This polyphenol sensitization strategy enriches the functionalization toolbox in material science, interface engineering, and environmental science.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Oleophilic foams for oil spill mitigation

A method of fabricating an oleophilic foam includes providing a foam comprising a base material. The base material is coated with an inorganic material using at least one of an atomic layer deposition (ALD), a molecular layer deposition (MLD) or sequential infiltration synthesis (SIS) process. The SIS process includes at least one cycle of exposing the foam to a first metal precursor for a first predetermined time and a first partial pressure. The first metal precursor infiltrates at least a portion of the base material and binds with the base material. The foam is exposed to a second co-reactant precursor for a second predetermined time and a second partial pressure. The second co-reactant precursor reacts with the first metal precursor, thereby forming the inorganic material on the base material. The inorganic material infiltrating at least the portion of the base material. The inorganic material is functionalized with an oleophilic material.

04 OIL SHALES AND TAR SANDS↗