Search NASA⌕ Search

Engineering topics

Mehl, Marco

Publications and source records attributed to Mehl, Marco.

At least 19 records

Experimental and computational investigation of the influence of iso -butanol on autoignition of n -decane and n -heptane in non-premixed flows

Experimental and computational investigation is carried out to elucidate the influence of iso-butanol on critical conditions of autoignition of n-decane and n-heptane. The counterflow configuration is employed. In this configuration an axisymmetric stream of air is directed over the surface of an evaporating pool of a liquid fuel. A stagnation plane is established. The temperature of the air is increased until autoignition is achieved in the mixing layer in the vicinity of the stagnation plane. The temperature of the air stream at autoignition, T ig , is measured at various values of the strain rate, which is defined as the axial gradient of the axial component of the flow velocity at the stagnation plane. Fuels tested are n-decane, n-heptane, iso-butanol and various mixtures of n-decane/iso-butanol and n-heptane/iso-butanol. Kinetic modeling is carried out using the recently updated version of the comprehensive CRECK chemical-kinetic mechanism. Critical conditions of autoignition are predicted for all fuels and fuel mixtures and the results are compared with the measurements. Computations show that low-temperature chemistry plays a significant role in promoting autoignition of n-decane and n-heptane, and the influence of low-temperature chemistry decreases with increasing strain rates because there is insufficient residence for the low-temperature reactions to take place. Experimental data and numerical simulations show that addition of even small amounts of iso-butanol to n-decane or n-heptane increases the value of T ig at low strain rates indicating that iso-butanol strongly inhibits the low-temperature chemistry of n-decane and n-heptane. Furthermore, the simulations show that when iso-butanol is present in the liquid fuel, only a small amount of n-decane is available in the gas phase and its low concentration cannot effectively sustain the low temperature degenerate branching oxidation process. Here, predicted flame structures show that the peak values of mole fraction of ketohydroperoxide are significantly reduced when iso-butanol is added to n-decane indicating that the kinetic pathway to low temperature ignition is blocked. This observation is confirmed from sensitivity analysis.

42 ENGINEERING↗

Autoignition and preliminary heat release of gasoline surrogates and their blends with ethanol at engine-relevant conditions: Experiments and comprehensive kinetic modeling

This work utilizes a rapid compression machine (RCM) to experimentally quantify autoignition and preliminary heat release characteristics for blends of 0 to 30% ethanol by volume into two surrogates (FGF-LLNL and FGF-KAUST) that represent a full boiling range gasoline (FACE-F). Experimental conditions cover pressures from 15 to 100 bar, temperatures from 700 to 1000 K, and diluted/stoichiometric and undiluted/lean fuel loading conditions representative of boosted spark-ignition and advanced compression ignition engines, respectively. Direct comparison is made with previously reported results for FACE-F/E0–E30 blends. Here, a detailed gasoline surrogate chemistry model is also proposed, and chemical kinetic modeling is undertaken using the proposed model to generate chemical insights into the compositional effects and ethanol blending effects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Simulating combustion of a seven-component surrogate for a gasoline/ethanol blend including soot formation and comparison with experiments

Combustion of a seven-component surrogate for a research grade 87 octane gasoline mixed with 10% ethanol is investigated experimentally and numerically from the perspective of an isolated droplet burning under conditions that promote one-dimensional gas transport. The numerical analysis included a kinetic mechanism comprised of 398 species and 24,814 reactions and a soot model that accounted for nucleation, surface growth, coalescence/aggregation of soot particles, and luminous flame radiation. Measurements of droplet and flame diameters were made for an initial droplet diameter (D o ) of approximately 0.63 mm. The simulations agreed well with the measurements including the location of the soot shell. Preferential vaporization was revealed by simulations of the liquid concentrations in the droplet. Predicted peak soot volume fractions coincided with temperatures between 1300 K and 1400 K as a soot inception temperature. Simulations were also carried out for D o between 0.25 mm and 5 mm to explore the effect of radiation and D o on burning. Below 0.25 mm radiation was negligible and burning rates and flame temperatures converged to a single value. Increasing D o up to 1.8 mm lowered the burning rate with luminous radiation having a strong effect. When radiation was entirely removed from the model the burning rate was nearly constant. Above D o = 2 mm droplets extinguished almost immediately after ignition. The flame temperature decreased with increasing D o while it increased when radiation was omitted. As a result, the simulations show that soot precursors including polyaromatic hydrocarbons were concentrated around the soot shell.

42 ENGINEERING↗

Experimental and kinetic modeling study of tetralin: A naphtheno-aromatic fuel for gasoline, jet and diesel surrogates

Distillate fuels contain significant proportions of naphtheno-aromatic components and tetralin is a suitable surrogate component to represent this molecular moiety. The presence of aromatic and naphthyl rings makes kinetic modeling of tetralin very challenging. Primary radicals formed during the oxidation of tetralin can be aryl, benzylic or paraffinic in nature. Using available information on reaction paths and rate constants of naphthenes and alkyl-aromatics, in this study a kinetic model of tetralin has been developed with emphasis on low-temperature chemistry and high-pressure conditions. Due to the lack of high-level quantum chemical calculations on reaction pathways of tetralin, analogous rates from ab-initio studies on benzylic and paraffinic radicals have been adopted here. Some modifications to the reaction rate rules are incorporated to account for the unique characteristics of tetralin's molecular structure. Important reaction channels have been identified using reaction path and brute force sensitivity analyses. In order to investigate the model performance at low temperatures, new experiments are carried out in a rapid compression machine on blends of tetralin and 3-methylpentane. Blending of low-reactivity tetralin with a high-reactivity alkane allowed the investigation of tetralin ignition at very low temperatures (665 – 856 K). The kinetic model developed in the current study is found to predict the current experiments and literature data adequately. The new model will aid in high-fidelity surrogate predictions at engine-relevant conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Autoignition of CRC diesel surrogates at low temperature combustion conditions: Rapid compression machine experiments and modeling

As federal programs require increasingly stringent engine emissions and fuel economy standards, these ambitions can only be met if next-generation combustion technology is developed focusing on high-efficiency and low-emissions engines. Recent research has indicated the need to operate engines at higher compression ratios and with low temperature combustion (LTC) to achieve the needed gains in engine efficiency and reductions in emissions. Because there is a lack of understanding of the chemistry of diesel fuel components and their mixtures at these LTC conditions, this limits the ability to develop predictive chemical kinetic models that can be used to optimize engine combustion. The current study aims to fill in gaps in fundamental combustion data on surrogate fuel mixtures relevant to diesel fuels. Specifically, four multicomponent diesel surrogates formulated by the Coordinating Research Council (CRC) to emulate an ultra-low-sulfur research-grade #2 certification diesel fuel (CFA), namely V0a (4 components), V0b (5 components), V1 (8 components), and V2 (9 components), have been investigated in a rapid compression machine (RCM) through determination of total and first-stage ignition delay times. Autoignition characteristics of lean to rich fuel/O 2 /N 2 mixtures, for the four CRC surrogates and CFA, have been measured using an RCM at LTC relevant pressures and temperatures, in the ranges of 10–20 bar and 650–1000 K, respectively. The equivalence ratios have been varied by independently changing the oxygen mole fraction and the fuel mole fraction in the test mixtures, thereby illustrating the individual effects of oxygen concentration and fuel loading on diesel autoignition. Autoignition results of these four CRC surrogates are compared among them and with those of CFA. Some degree of agreement in autoignition response between each CRC surrogate and CFA is observed, while discrepancies are also identified and discussed. In addition, a detailed chemical kinetic model for diesel surrogates has been developed and validated against these newly-acquired RCM data. We find that this model shows reasonable agreement with the overall ignition delay time results of the current RCM experiments. Chemical kinetic analyses of the developed model were further conducted to help identify the reactions controlling the autoignition processes and the consumption of fuel components in CRC surrogates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Autoignition behavior of gasoline/ethanol blends at engine-relevant conditions

Ethanol is an attractive oxygenate increasingly used for blending with petroleum-derived gasoline yielding beneficial combustion and emissions behavior for a range of internal combustion engine schemes, including stoichiometric spark-ignition and low temperature combustion (LTC). As such, it is important to fundamentally understand the autoignition behavior of gasoline/ethanol blends. This work utilizes a rapid compression machine (RCM) and a homogeneous charge compression ignition (HCCI) engine to experimentally quantify changes in fuel reactivity, through ignition delay times and preliminary heat release, for blends of 0 to 30% vol./vol. into a full boiling range research gasoline (FACE-F). Diluted/stoichiometric and undiluted/fuel-lean conditions are explored covering a wide range of compressed temperatures and pressures relevant to conventional and advanced, gasoline combustion engines. Detailed chemical kinetic modeling is undertaken using a recently updated gasoline surrogate model in conjunction with a five-component surrogate to model the RCM experiments and provide chemical insight into the perturbative effects of ethanol on the autoignition process. The diluted/stoichiometric RCM measurements reveal that within the low-temperature regime ethanol retards first-stage and main ignition delay times, and suppresses both the rates and extents of low-temperature heat release (LTHR), while within the intermediate-temperature regime ethanol only causes slight changes. Good agreement of ignition delay time and preliminary heat release prediction is found between model and experimental results. Sensitivity and flux analyses further show that ethanol blending effects are dominated by the competition between the H-atom abstraction from ethanol and other fuel components by OH radical at low temperatures and by HO 2 radical at intermediate temperatures. These findings are consistent across both fuel loading conditions explored in this study. In addition, when HCCI engine experiments are mapped onto undiluted/lean RCM measurements under a constant combustion phasing scenario, good correspondence between the two apparatuses is observed for LTHR and start of high-temperature heat release. Finally, the current study highlights the importance of characterizing LTHR in predicting fuel behaviors in high-boost/low-temperature engines, and demonstrates that RCM experiments can provide an alternative, and more-efficient avenue for such characterization.

02 PETROLEUM↗

Exploring gasoline oxidation chemistry in jet stirred reactors

Recent decades have seen increasingly restrictive regulations applied to gasoline engines. Gasoline combustion chemistry must be investigated to achieve a better understanding and control of internal combustion engine efficiency and emissions. In this work, several gasoline fuels, namely the FACE (Fuel for Advanced Combustion Engines) gasolines, were selected as targets for oxidation study in jet-stirred reactors (JSR). The study is facilitated by formulating various gasoline surrogate mixtures with known hydrocarbon compositions to represent the real gasolines. Surrogates included binary mixtures of n-heptane and iso-octane, as well as more complex multi-component mixtures. Here, the oxidation characteristics of FACE gasolines and their surrogates were experimentally examined in JSR-1 and numerically simulated under the following conditions: pressure 1 bar, temperature 500–1050 K, residence time 1.0 and 2.0 s, and two equivalence ratios (Φ= 0.5 and 1.0). In the high temperature region, all real fuels and surrogates showed similar oxidation behavior, but in the low temperature region, a fuel’s octane number and composition had a significant effect on its JSR oxidation characteristics. Low octane number fuels displayed more low temperature reactivity, while fuels with similar octane number but a larger number of n-alkane components were more reactive. A gasoline surrogate kinetic model was examined with FACE gasoline experiments either measured in JSR-2, or taken from previous work under the following conditions: pressure 10 bar, temperature 530–1200 K, residence time 0.7 s, and three equivalence ratios (Φ = 0.5, 1.0 and 2.0). Comparison between FACE gasoline experimental results with surrogate model predictions showed good agreement, demonstrating considerable potential for surrogate fuel kinetic modeling in engine simulations.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

An experimental and kinetic modeling study of the oxidation of hexane isomers: Developing consistent reaction rate rules for alkanes

Alkanes are key components in gasoline, jet and diesel fuels and considerably influence the combustion behavior of these fuels because of their wide range of reactivity. An improved understanding of their combustion behavior and the development of chemical kinetic models that can accurately simulate their combustion behavior are important for the development of next-generation internal-combustion and gas-turbine engines. The current work provides here improved insight into oxidation mechanisms of a representative family of hydrocarbon fuels, specifically the hexane isomers: n-hexane, 2-methylpentane, 3-methylpentane, 2,2-dimethylbutane and 2,3-dimethylbutane. These isomers provide carbon “skeletons” ranging from straight-chained to highly-branched and provide a framework for the subsequent development of kinetic mechanisms for larger alkanes. New ignition delay times for the four branched hexane isomers were measured in a high-pressure shock tube and in a rapid compression machine, both at stoichiometric conditions (φ = 1), p = 15 bar and X O2 = 21% over temperatures from 600 to1300 K. These data were combined with previously published measurements under the same conditions for the remaining n-hexane isomer to provide a complete body of experimental data for kinetic modeling analysis. In addition, very recent experimental measurements of individual intermediate chemical species concentrations from all five hexane isomers in a jet-stirred reactor are also included and provide another family of data for further assessment of hexane isomer reactivity. Different reactivities were observed for each hexane isomer in each experimental facility, resulting from differences in their molecular structures. Consistent reaction rate rules have been applied to develop a combined detailed chemical kinetic model for all five hexane isomers. Kinetic model validation studies are reported to show that the current model reproduces well the ignition delay times of all five alkane isomers, as well as their variations in reactivity over a wide range of temperatures and other operating conditions. Equally important, these results show that it is not necessary to have a separate, different kinetic model for each isomer of a family of alkane fuels and that a single, coherent, integrated set of reaction rate classes and rules is sufficient to accurately describe combustion rates of combustion of straight-chain n-alkanes and branched-chain alkane fuels. This suggests strongly that a single set of reaction classes and rate rules should be sufficient to describe combustion kinetics of alkane fuels of any size and degree of branching.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Impact of Ethanol additions on Autoignition Characteristics of a Full Boiling Range Gasoline and its Surrogates at Advanced Engine Conditions

Ethanol is widely blended into commercial gasolines, as an oxygenate to mitigate pollutant formation, as well as an octane enhancer to improve knock resistance. Ethanol can also facilitate the use of lower-grade, or less-refined gasoline in modern internal combustion (IC) engines. However, the chemical kinetic interactions of ethanol with petroleum-based gasoline are not well understood, especially towards autoignition propensity over a range of conditions. These interactions are critical for improving knock resistance, as well as towards performance in low temperature combustion schemes, such as gasoline compression ignition. This study investigates the chemical kinetic interactions of ethanol with a full boiling range gasoline, where blending ratios of 0 to 30 vol./vol. are covered. A mid-octane range (Anti Knock Index 91.5) Fuels for Advanced Combustion Engines gasoline is employed, while a variety of multi-component surrogate blends are also studied. Autoignition data are acquired within a rapid compression machine at temperature, pressure, and fuel loading conditions representative of advanced IC engines. Changes in low-temperature behavior, including first-stage ignition times and extents of low temperature heat release, as well as main ignition times are quantified for the neat fuels and the ethanol-blended fuels. A recently-updated, detailed chemical kinetic model for the gasoline surrogates is used to interpret the measurements, and better understand the kinetic pathways.

autoignition↗

Experimental and modeling study of the autoignition behavior of a standard oxygenated gasoline fuel

Gasoline surrogate models can be conveniently used to simulate the combustion behavior of fuels in internal combustion engines. Because of limitations in the number of robust models available and the high computational cost of running them, simple surrogates with only 2 or 3 components (namely n-heptane, iso-octane and toluene) have been long preferred to simulate the ignition behavior of gasoline in engine calculations. More recently, thanks to the development of new, well-validated kinetic models and the access to cheap high-performance computing, the scientific and engineering community is utilizing the higher fidelity provided by more complex mixture models. The added detail in composition can in fact better reproduce variation in the fuel reactivity with pressure (an important feature for downsized, boosted conditions) and blending behavior of real fuels. In this study, the ignition behavior of a research grade full blend oxygenated fuel matching the typical specification of US standard grade gasoline has been investigated by means of rapid compression experiments and detailed kinetic calculations. A multicomponent fuel surrogate model has been developed using compositional information and a surrogate optimization tool. Based on the experimental and computational results presented in this study, general considerations about guidelines in the formulation of gasoline fuel surrogates are provided.

autoignition↗

Experimental and modeling study of chemical-based strategies for mitigating dust formation in fusion reactors [Plasma Flow Reactor Chemical Kinetics: A Method Toward Optimizing Nano-Manufacturing and Laser Inertial Fusion Energy Strategies]

We studied carbon/hydrogen/oxygen chemical kinetics at time scales and thermal conditions relevant to fusion energy applications using a custom-built plasma flow reactor to investigate chemical-based strategies for eliminating carbon dust formation in fusion reactors. Acetylene and oxygen gases under varying conditions of initial concentrations are injected into an inductively coupled argon plasma where complete molecular dissociation occurs. The evolution of chemical species is investigated along the plasma flow reactor as a function of temperature and residence time. Atomized species of C, H, and O cool from 5000 K to 1000 K within 30 ms at atmospheric pressures. We employed optical emission and infrared absorption spectroscopy to measure the reaction intermediates (e.g. C 2 ) and products (e.g. C 2 H 2 ). Chemical equilibrium models are inadequate to describe the evolution of carbon molecular products, and thus a chemical kinetics model is developed. In both experiments and kinetic modelling, we find that the addition of oxygen in 1:1 proportion to carbon strongly favors the formation of CO, preventing the formation of acetylene (an important soot precursor) in less than 10 milliseconds. The kinetics model is also used to perform a reaction sensitivity and a rate of production analyses to identify the rate determining steps and the major chemical pathways that control the acetylene production/consumption. The results demonstrate the feasibility of chemical-based strategies for eliminating the formation of carbonaceous particles in fusion energy reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Kinetic modeling study of surrogate components for gasoline, jet and diesel fuels: C7-C11 methylated aromatics

Kinetic mechanisms for aromatics are needed to successfully simulate the autoignition of transportation fuels using the surrogate fuel approach. An aromatic detailed kinetic mechanism that describes kinetics of C7-C11 methylated aromatics, including toluene, o-xylene, p-xylene, 1,2,4-trimethylbenzene, 1,3,5, trimethyl-benzene and alpha-methylnaphthalene has been developed in the current study. The kinetic mechanism was built hierarchically using similar set of reaction pathways and reaction rate rules. In the mechanism developed, special emphasis is put on describing the detailed low-temperature ignition chemistry of o-xylene and 1,2,4-trimethylbenzene and, to our knowledge, this is the first attempt to do so in a detailed kinetic mechanism. In addition to kinetic modeling, new experimental data were acquired for toluene, o-xylene, and 1,2,4-trimethylbenzene using a rapid compression machine at low-to-intermediate temperatures and engine relevant pressures. In addition, the mechanism has been compared against data sets from the literature covering ignition delay times, flame speeds, and speciation profiles measured in a jet-stirred reactor and flow reactor. Good agreement is observed between the mechanism predictions and the experimental data. Kinetic analysis demonstrated the importance of including the low temperature chemistry of the benzylperoxy radicals to accurately capture the ignition propensity of o-xylene and 1,2,4-trimethylbenzene at low-to-intermediate temperatures and high pressures. The kinetic mechanism developed in the current study can be used for surrogate modeling of gasoline, jet and diesel fuels. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

02 PETROLEUM↗

Low temperature autoignition of 5-membered ring naphthenes: Effects of substitution [Low temperature autoignition study of substituted 5-membered ring naphthenes]

The development and design of future internal combustion engines requires fundamental understanding and the capability to model the autoignition and pollutant formation behavior of petroleum-based and other fuels. Naphthenes are an important constituent of gasoline, and they can comprise larger portions of unconventionally-derived gasoline. There is a lack of data and validated models for 5-membered ring naphthenes. In this work, the autoignition characteristics of cyclopentane, and two of its substituted analogues, methylcyclopentane, and ethylcyclopentane are investigated using a twin-piston rapid compression machine. Each fuel is studied at engine-representative conditions: 20, 50 bar and 700-980K, with mixtures containing stoichiometric fuel/oxygen ratios at various extents of dilution with inert gases. Negative temperature coefficient (NTC) behavior is observed for cyclopentane, though first-stage ignition and associated low temperature heat release behavior are only evident at temperatures below that for the transition to NTC. Pressure is found to have a larger impact on the reactivity than oxygen dilution, with both effects amplified in the NTC region. The cyclopentane experiments in this study are challenged by the sensitivity of this molecule to non-uniform, or mild ignition phenomena within the NTC region. The addition of saturated sidechains in methyl- and ethylcyclopentane significantly increases the reactivity of the molecules, especially at low temperature and NTC conditions. At the highest temperatures though, there is little difference between the three naphthenes. Typical two-stage ignition behavior is observed across a wide range of temperatures for these alkyl cyclopentanes with no mild ignition observed within the NTC region. A recently developed model for cyclopentane is extended to include reactions for methylcyclopentane, and this is used to simulate the new experiments. The simulation results indicate that low temperature reactivity of cyclopentane is dominated by HO 2 elimination of the RO 2 species producing cyclopentene, and this inhibits autoignition since it is a very stable molecule. When a methyl group is substituted on the ring, additional RO 2 isomerization pathways are available, and these substantially increase the fuel reactivity. HO 2 elimination is also important with methylcyclopentane, and this leads to significant production of cyclic olefins which can further react to produce diolefins. Furthermore, these findings are consistent with observations that have been made in other experimental apparatuses.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Auto-ignition study of FACE gasoline and its surrogates at advanced IC engine conditions

Robust surrogate formulation for gasoline fuels is challenging, especially in mimicking auto-ignition behavior observed under advanced combustion strategies including boosted spark-ignition and advanced compression ignition. This work experimentally quantifies the auto-ignition behavior of bi- and multi-component surrogates formulated to represent a mid-octane (Anti-Knock Index 91.5), full boiling-range, research grade gasoline (Fuels for Advanced Combustion Engines, FACE-F). A twin-piston rapid compression machine is used to achieve temperature and pressure conditions representative of in-cylinder engine operation. Changes in low- and intermediate-temperature behavior, including first-stage and main ignition times, are quantified for the surrogates and compared to the gasoline. This study identifies significant discrepancies in the first-stage ignition behavior, the influence of pressure for the bi- to ternary blends, and highlights that better agreement is achieved with multi-component surrogates, particularly at lower temperature regimes. A recently-updated detailed kinetic model for gasoline surrogates is also used to simulate the measurements. Finally, sensitivity analysis is employed to interpret the kinetic pathways responsible for reactivity trends in each gasoline surrogate.

36 MATERIALS SCIENCE↗