Search NASA⌕ Search

Engineering topics

Mehl, Marco

Publications and source records attributed to Mehl, Marco.

At least 37 records · Page 2

Co-Optimization of Fuels & Engines: Properties of Co-Optima Core Research Gasolines

The Co-Optima Core gasolines are a set of fuels developed to have similar autoignition properties but a wide range of composition. The primary compositional components varied were isoparaffins, cycloparaffins, olefins, aromatics, and ethanol. These fuels are being used extensively across the DOE national laboratories in fuel property and engine combustion research.They provide a consistent baseline across research platforms. This document is a compilation of chemical analysis and property data on these fuels, including basic properties such as density, octane numbers, heating value, Reid vapor pressure, and distillation. Elemental composition is reported, as well as detailed hydrocarbon analysis and functional group analysis by NMR spectroscopy. Enthalpy of vaporization at 20 deg C as well as true vapor pressure over the temperature range -20 deg to 120 deg C are also reported.

30 DIRECT ENERGY CONVERSION↗

Gas Phase Chemical Evolution of Uranium, Aluminum, and Iron Oxides

Abstract We use a recently developed plasma-flow reactor to experimentally investigate the formation of oxide nanoparticles from gas phase metal atoms during oxidation, homogeneous nucleation, condensation, and agglomeration processes. Gas phase uranium, aluminum, and iron atoms were cooled from 5000 K to 1000 K over short-time scales (∆t < 30 ms) at atmospheric pressures in the presence of excess oxygen. In-situ emission spectroscopy is used to measure the variation in monoxide/atomic emission intensity ratios as a function of temperature and oxygen fugacity. Condensed oxide nanoparticles are collected inside the reactor for ex-situ analyses using scanning and transmission electron microscopy (SEM, TEM) to determine their structural compositions and sizes. A chemical kinetics model is also developed to describe the gas phase reactions of iron and aluminum metals. The resulting sizes and forms of the crystalline nanoparticles (FeO-wustite, eta-Al 2 O 3 , UO 2 , and alpha-UO 3 ) depend on the thermodynamic properties, kinetically-limited gas phase chemical reactions, and local redox conditions. This work shows the nucleation and growth of metal oxide particles in rapidly-cooling gas is closely coupled to the kinetically-controlled chemical pathways for vapor-phase oxide formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Autoignition of trans -decalin, a diesel surrogate compound: Rapid compression machine experiments and chemical kinetic modeling

Decahydronaphthalene (decalin), with both cis and trans isomers, is a bicyclic alkane that is found in aviation fuels, diesel fuels, and alternative fuels from tar sands and oil shales. Between the two decalin isomers, trans-decalin has a lower cetane number, is energetically more stable, and has a lower boiling point. Moreover, trans-decalin has often been chosen as a surrogate component to represent two-ring naphthenes in transportation fuels. Recognizing the importance of understanding the chemical kinetics of trans-decalin in the development of surrogate models, an experimental and modeling study has been conducted. Experimentally, the autoignition characteristics of trans-decalin were investigated using a rapid compression machine (RCM) by using trans-decalin/O2/N2 mixtures at compressed pressures of PC=10–25 bar, low-to-intermediate compressed temperatures of TC=620–895 K, and varying equivalence ratios of Φ=0.5, 1.0, and 2.0. These new experimental data demonstrate the effects of pressure, fuel loading, and oxygen concentration on autoignition of trans-decalin. The current RCM data of trans-decalin at lower temperatures were also found to complement well with the literature shock tube data of decalin (mixture of cis+trans) at higher temperatures. Furthermore, a chemical kinetic model for the oxidation of trans-decalin has been developed with new reaction rates and pathways, including, for the first time, a fully-detailed representation of low-temperature chemical kinetics for transdecalin. This model shows good agreement with the overall ignition delay results of the current RCM experiments and the literature shock tube studies. Chemical kinetic analyses of the developed model were further conducted to help identify the fuel decomposition pathways and the reactions controlling the autoignition at varying conditions.

10 SYNTHETIC FUELS↗

Multi-fuel surrogate chemical kinetic mechanisms for real world applications

The most important driving force for development of detailed chemical kinetic reaction mechanisms in combustion is the desire by researchers to simulate practical systems. Here, this article reviews the parallel evolution of kinetic reaction mechanisms and applications of those models to practical, real engines. Early, quite simple, kinetic models for small fuel molecules were extremely valuable in analyzing long-standing, poorly understood applied ignition and flame quenching problems, and later kinetic models have been applied to much more complex flame propagation, problems including autoignition in spark-ignition engines and issues related to octane numbers and knock in modern, high compression ratio and other engines. The recent emergence of very large, multi-fuel surrogate kinetic mechanisms that can address many different fuel types and real engine applications is discussed as a modern analytical tool that can be used for a wide variety of practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental and modeling studies of a biofuel surrogate compound: laminar burning velocities and jet-stirred reactor measurements of anisole

Lignocellulosic biomass is a promising alternative fuel source which can promote energy security, reduce greenhouse gas emissions, and minimize fuel consumption when paired with advanced combustion strategies. Pyrolysis is used to convert lignocellulosic biomass into a complex mixture of phenolic-rich species that can be used in a transportation fuel. Anisole (or methoxybenzene) can be used as a surrogate to represent these phenolic-rich species. Anisole also has attractive properties as a fuel component for use in advanced spark-ignition engines because of its high blending research octane number of 120. Presented in the current work are new measurements of laminar burning velocities, jet-stirred reactor (JSR) speciation of anisole/O 2 /N 2 mixtures, and the development and validation of a detailed chemical kinetic mechanism for anisole. Homogeneous, steady state, fixed gas temperature, perfectly stirred reactor CHEMKIN simulations were used to validate the mechanism against the current JSR measurements and published JSR experiments from CNRS-Nancy. Pyrolysis and oxidation simulations were based on the experimental reactant compositions and thermodynamic state conditions including P = 1 bar and T = 675–1275 K. The oxidation compositions studied in this work span fuel-lean (φ = 0.5), stoichiometric, and fuel rich (φ = 2.0) equivalence ratios. Laminar burning velocities were measured on a heat flux stabilized burner at an unburnt T = 358 K, P = 1 bar and simulated using the CHEMKIN premixed laminar flame speed module. Ignition delay times of anisole were then simulated at conditions relevant to advanced combustion strategies. Current laminar burning velocity measurements and predicted ignition delay times were compared to gasoline components (e.g., n-heptane, iso-octane, and toluene) and gasoline surrogates to highlight differences and similarities in behavior. Reaction path analysis and sensitivity analysis were used to explain the pathways relevant to the current studies. Under pyrolysis and oxidative conditions, unimolecular decomposition of anisole to phenoxy radicals and methyl radicals was found to be important due to the relatively low bond strength between the oxygen and methyl group, ~65 kcal/mol. Finally, reactions of these abundant phenoxy radicals with O 2 were found to be critical to accurately reproduce anisole's reactivity.

10 SYNTHETIC FUELS↗

Plasma flow reactor for steady state monitoring of physical and chemical processes at high temperatures

Here, we present the development of a steady state plasma flow reactor to investigate gas phase physical and chemical processes that occur at high temperature (1000 < T < 5000 K) and atmospheric pressure. The reactor consists of a glass tube that is attached to an inductively coupled argon plasma generator via an adaptor (ring flow injector). We have modeled the system using computational fluid dynamics simulations that are bounded by measured temperatures. In situ line-of-sight optical emission and absorption spectroscopy have been used to determine the structures and concentrations of molecules formed during rapid cooling of reactants after they pass through the plasma. Emission spectroscopy also enables us to determine the temperatures at which these dynamic processes occur. A sample collection probe inserted from the open end of the reactor is used to collect condensed materials and analyze them ex situ using electron microscopy. The preliminary results of two separate investigations involving the condensation of metal oxides and chemical kinetics of high-temperature gas reactions are discussed.

36 MATERIALS SCIENCE↗

The Reduced Effectiveness of EGR to Mitigate Knock at High Loads in Boosted SI Engines

Numerous studies have demonstrated that exhaust gas recirculation (EGR) can attenuate knock propensity in spark ignition (SI) engines at naturally aspirated or lightly boosted conditions. In this paper, we investigate the role of cooled EGR under higher load conditions with multiple fuel compositions, where highly retarded combustion phasing typical of modern SI engines was used. It was found that under these conditions, EGR attenuation of knock is greatly reduced, where EGR doesn’t allow significant combustion phasing advance as it does under lighter load conditions. Detailed combustion analysis shows that when EGR is added, the polytropic coefficient increases causing the compressive pressure and temperature to increase. At sufficiently highly boosted conditions, the increase in polytropic coefficient and additional trapped mass from EGR can sufficiently reduce fuel ignition delay to overcome knock attenuation effects. Kinetic modeling demonstrates that the effectiveness of EGR to mitigate knock is highly dependent on the pressure-temperature condition. Experiments at 2000 rpm have confirmed reduced fuel ignition delay under highly boosted conditions relevant to modern downsized boosted SI engines, where in-cylinder pressure is higher and the temperature is cooler. Finally, at these conditions, charge reactivity increases compared to naturally aspirated conditions, and attenuation of knock by EGR is reduced.

33 ADVANCED PROPULSION SYSTEMS↗

A comprehensive iso-octane combustion model with improved thermochemistry and chemical kinetics

Iso-Octane (2,2,4-trimethylpentane) is a primary reference fuel and an important component of gasoline fuels. Furthermore, it is a key component used in surrogates to study the ignition and burning characteristics of gasoline fuels. This paper presents an updated chemical kinetic model for iso-octane combustion. Specifically, the thermodynamic data and reaction kinetics of iso-octane have been re-assessed based on new thermodynamic group values and recently evaluated rate coefficients from the literature. The adopted rate coefficients were either experimentally measured or determined by analogy to theoretically calculated values. New alternative isomerization pathways for peroxy-alkyl hydroperoxide ($\dot{O}$OQOOH) radicals were added to the reaction mechanism. The updated kinetic model was compared against new ignition delay data measured in rapid compression machines (RCM) and a high-pressure shock tube. Our experiments were conducted at pressures of 20 and 40 atm, at equivalence ratios of 0.4 and 1.0, and at temperatures in the range of 632–1060 K. The updated model was further compared against shock tube ignition delay times, jet-stirred reactor oxidation speciation data, premixed laminar flame speeds, counterflow diffusion flame ignition, and shock tube pyrolysis speciation data available in the literature. Finally, the updated model was used to investigate the importance of alternative isomerization pathways in the low temperature oxidation of highly branched alkanes. When compared to available models in the literature, the present model represents the current state-of-the-art in fundamental thermochemistry and reaction kinetics of iso-octane; and thus provides the best prediction of wide ranging experimental data and fundamental insights into iso-octane combustion chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The role of correlations in uncertainty quantification of transportation relevant fuel models

Large reaction mechanisms are often used to describe the combustion behavior of transportation-relevant fuels like gasoline, where these are typically represented by surrogate blends, e.g., n-heptane/iso-octane/toluene. We describe efforts to quantify the uncertainty in the predictions of such mechanisms at realistic engine conditions, seeking to better understand the robustness of the model as well as the important reaction pathways and their impacts on combustion behavior. In this work, we examine the importance of taking into account correlations among reactions that utilize the same rate rules and those with multiple product channels on forward propagation of uncertainty by Monte Carlo simulations. Automated means are developed to generate the uncertainty factor assignment for a detailed chemical kinetic mechanism, by first uniquely identifying each reacting species, then sorting each of the reactions based on the rate rule utilized. Simulation results reveal that in the low temperature combustion regime for iso-octane, the majority of the uncertainty in the model predictions can be attributed to low temperature reactions of the fuel sub-mechanism. The foundational, or small-molecule chemistry (C 0 -C 4 ) only contributes significantly to uncertainties in the predictions at the highest temperatures (Tc=900 K). Accounting for correlations between important reactions is shown to produce non-negligible differences in the estimates of uncertainty. Including correlations among reactions that use the same rate rules increases uncertainty in the model predictions, while accounting for correlations among reactions with multiple branches decreases uncertainty in some cases. Significant non-linear response is observed in the model predictions depending on how the probability distributions of the uncertain rate constants are defined.Finally, we concluded that care must be exercised in defining these probability distributions in order to reduce bias, and physically unrealistic estimates in the forward propagation of uncertainty for a range of UQ activities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fuel Property Blend Model

The object of this project is to develop chemical models and associated correlations to predict the blending behavior of bio-derived fuels when mixed with conventional fuels like gasoline and diesel fuels.

30 DIRECT ENERGY CONVERSION↗

Probing the antagonistic effect of toluene as a component in surrogate fuel models at low temperatures and high pressures. A case study of toluene/dimethyl ether mixtures

There is a dearth of experimental data which examine the fundamental low-temperature ignition (T < 900 K) behavior of toluene resulting in a lack of data for the construction, validation, and interpretation of chemical kinetic models for commercial fuels. In order to gain a better understanding of its combustion chemistry, dimethyl ether (DME) has been used as a radical initiator to induce ignition in this highly knock resistant aromatic, and its influence on the combustion of toluene ignition was studied in both shock tube and rapid compression machines as a function of temperature (624–1459 K), pressure (20–40 atm), equivalence ratio (0.5–2.0), and blending ratio (100% toluene, 76% toluene (76T/24D), 58% toluene (58T/42D), 26% toluene (26T/74D) and 100% DME). We use several literature chemical kinetic models to interpret our experimental results. For mixtures containing high concentrations of toluene at low-temperatures none of these are capable of reproducing experiment. This then implies an incomplete understanding of the low-temperature oxidation pathways which control its ignition in our experimental reactors, and by extension, in spark- (SI) and compression-ignition (CI) engines, and an updated detailed chemical kinetic model is presented for engineering applications. Model analyses indicate that although the initial fate of the fuel is dominated by single-step H-atom abstraction reactions from both the benzylic and phenylic sites, the subsequent fate of the allylic and vinylic radicals formed is much more complex. Further experimental and theoretical endeavors are required to gain a holistic qualitative and quantitative chemical kinetics based understanding of the combustion of pure toluene, toluene blends, and commercial fuels containing other aromatic components, at temperatures of relevance to SI and CI engines.

30 DIRECT ENERGY CONVERSION↗

Chemical kinetics of octane sensitivity in a spark-ignition engine (Chemical Kinetics of Octane Sensitivity in a Spark Ignition Engine)

This article uses a chemical kinetic modeling approach to study the influences of fuel molecular structure on Octane Sensitivity (OS) in Spark Ignition (SI) engines. Octane Sensitivity has the potential to identify fuels that can be used in next-generation high compression, turbocharged SI engines to avoid unwanted knocking conditions and extend the range of operating conditions that can be used in such engines. While the concept of octane numbers of different fuels has been familiar for many years, the variations of their values and their role in determining Octane Sensitivity have not been addressed previously in terms of the basic structures of the fuel molecules. In particular, the importance of electron delocalization on low temperature hydrocarbon reactivity and its role in determining OS in engine fuel is described here for the first time. Finally, the role of electron delocalization on fuel reactivity and Octane Sensitivity is illustrated for a very wide range of engine fuel types, including n-alkane, 1-olefin, n-alcohol, and n-alkyl benzenes, and the unifying features of these fuels and their common trends, using existing detailed chemical kinetic reaction mechanisms that have been collected and unified to produce an overall model with unprecedented capabilities.

30 DIRECT ENERGY CONVERSION↗

Elucidating reactivity regimes in cyclopentane oxidation: Jet stirred reactor experiments, computational chemistry, and kinetic modeling

This study is concerned with the identification and quantification of species generated during the combustion of cyclopentane in a jet stirred reactor (JSR). Experiments were carried out for temperatures between 740 and 1250 K, equivalence ratios from 0.5 to 3.0, and at an operating pressure of 10 atm. The fuel concentration was kept at 0.1% and the residence time of the fuel/O 2 /N 2 mixture was maintained at 0.7 s. The reactant, product, and intermediate species concentration profiles were measured using gas chromatography and Fourier transform infrared spectroscopy. The concentration profiles of cyclopentane indicate inhibition of reactivity between 850-1000 K for φ=2.0 and φ=3.0. This behavior is interesting, as it has not been observed previously for other fuel molecules, cyclic or non-cyclic. A kinetic model including both low- and high-temperature reaction pathways was developed and used to simulate the JSR experiments. The pressure-dependent rate coefficients of all relevant reactions lying on the PES of cyclopentyl + O 2 , as well as the C-C and C-H scission reactions of the cyclopentyl radical were calculated at the UCCSD(T)-F12b/cc-pVTZ-F12//M06-2X/6-311++G(d,p) level of theory. The simulations reproduced the unique reactivity trend of cyclopentane and the measured concentration profiles of intermediate and product species. Furthermore, sensitivity and reaction path analyses indicate that this reactivity trend may be attributed to differences in the reactivity of allyl radical at different conditions, and it is highly sensitive to the C-C/C-H scission branching ratio of the cyclopentyl radical decomposition.

30 DIRECT ENERGY CONVERSION↗