Search NASA⌕ Search

Engineering topics

Menees, Gene P.

Publications and source records attributed to Menees, Gene P..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Numerical simulations of an oblique detonation wave engine

An account is given of the numerical methods employed in a code for the simulation of supersonic combustion, which is then applied to the simulation of attached detonations and flames associated with the oblique-detonation wave supersonic combustor concept. The addition of heat by a detonation wave results in a shorter combustor than can be obtained in more conventional scramjet designs. Pure oblique detonations have been produced in a stoichiometric, uniformly mixed hydrogen/air stream; the wave rotates upstream with energy release, according to simple analytical arguments. Flow visualization maps for Mach number and temperature are presented.

Cambier, Jean-Luc↗
NASA NTRS1988

Analytical and experimental validation of the Oblique Detonation Wave Engine concept

The Oblique Detonation Wave Engine (ODWE) for hypersonic flight has been analytically studied by NASA using the CFD codes which fully couple finite rate chemistry with fluid dynamics. Fuel injector designs investigated included wall and strut injectors, and the in-stream strut injectors were chosen to provide good mixing with minimal stagnation pressure losses. Plans for experimentally validating the ODWE concept in an arc-jet hypersonic wind tunnel are discussed. Measurements of the flow field properties behind the oblique wave will be compared to analytical predictions.

Adelman, Henry G.↗
NASA NTRS1988

Entry aeromaneuvering capabilities of transatmospheric vehicles

The landing footprint of a conceptual high-lift transatmospheric vehicle is defined for aeromaneuvering entry from a typical low-earth orbit. The flight strategy for trajectory construction to maximize the landing area by extending downrange and crossrange as far as possible is developed in four phases by optimal programming of the vehicle's roll angle. Trajectories that reach any given landing site were calculated with the corresponding heating rates at three critical vehicle locations (stagnation point, wing leading edge, and body centerline). An optimization methodology was developed that demonstrates the trades between crossrange, peak heating and total heat loads as a function of three key flight parameters (altitude, flight-path angle, and vehicle roll angle). The maximum extent of the landing footprint was found to be 29,690 km downrange and 6560 km crossrange. Large variations in the ballistic coefficient had negligible effect on the extent of the footprint but could significantly affect heating. However, the footprint's longitude was displaced downstream or upstream with increasing or decreasing ballistic coefficient, respectively.

Menees, Gene P.↗
NASA NTRS1987

Aeroassisted-vehicle design studies for a manned Mars mission

An aerobrake design that has matured over several years of development accounting for all of the important flow phenomenology which are characteristic of aerobraking vehicles is proposed as the mission baseline. Flight regimes and aerothermal environments for both Mars and Earth entry are calculated using advanced methods to account for real-gas, thermochemical, relaxation effects. The results are correlated with thermal-protection and structural requirements and mission performance capability. The importance of nonequilibrium radiative heating for Earth aerocapture is demonstrated. It is suggested that two aerobrakes of different sizes will produce optimal performance for the three phases of the mission (i.e., one aerobrake for Mars aerocapture and descent of the surface lander and another for Earth return).

Menees, Gene P.↗
NASA NTRS1987

Aeroassisted-vehicle design studies for a manned Mars mission

An aerobrake design accounting for all of the important flow phenomenology which are characteristic of aerobraking vehicles is proposed as the mission baseline. Flight regimes and aerothermal environments for both Mars and earth entry are calculated using advanced methods to account for real-gas, thermochemical, relaxation effects. The results are correlated with thermal-protection and structural requirements and mission performance capability. The importance of nonequilibrium radiative heating for earth aerocapture is demonstrated. It is suggested that two aerobrakes of different sizes will produce optimal performance for the three phases of the mission (i.e., one aerobrake for Mars aerocapture and descent of the surface lander and another for earth return).

Menees, Gene P.↗
NASA NTRS1987

Ascent aeromaneuvering capabilities of transatmospheric vehicles

The low-earth orbit rendezvous capability of a conceptual transatmospheric vehicle is analyzed for two endo-/exo-atmospheric ascent missions. Both cases involve coasting aerodynamic maneuvers starting from the burn-out conditions corresponding to air-breathing propulsion systems that achieve orbital velocity within the atmosphere. The powered phase of the ascent trajectories approximate constant dynamic pressure, fuel-efficient flightpaths typically flown by supersonic aircraft. The aeromaneuvering coast phases of the ascent include both coplanar (to determine altitude capability without plane-inclination changes) and aeroturning to LEO rendezvous at 400 km altitude (to assess plane-change capability). The coast-phase ascent maneuvers are correlated with G-load requirements and aerothermodynamic heating characteristics at two critical locations on the vehicle surface (i.e., the nose stagnation point and the body centerline). The results are correlated and recommendations are made concerning thermal protection and structural requirements.

Menees, Gene P.↗
NASA NTRS1987

Synergetic plane-change capability of a conceptual aeromaneuvering-orbital-transfer vehicle

The flight strategy for a general low-earth orbit plane-change is analyzed for a conceptual, high-lift, aeromaneuvering-orbital-transfer vehicle, and applied to the important case of the 45 deg plane-inclination change. The study focuses on two principal methods: (1) the procedure to obtain a change in the inclination of the vehicle's orbital plane, and (2) the full rendezvous procedure. Optimal trajectories for minimal propellant use during the synergetic aerotransit are developed, which incorporate best estimates of constraints imposed by reusable thermal-protection requirements and human tolerance to g-load levels. The performance capability for one-way payload delivery to the target orbit is analyzed in detail and the capability for return to the base orbit demonstrated.

Menees, Gene P.↗
NASA NTRS1985

Aerothermodynamic Heating Analysis of Aerobraking and Aeromaneuvering Orbital Transfer Vehicles

The thermal-protection requirements of two aeroassisted orbital transfer vehicles (AOTVS) are analyzed for return missions between the geosynchronous and Shuttle orbits. One of the designs is a specialized version of a previously proposed generic aerobraking vehicle that Is capable of only delivery-type operations. The other Is a high-lift aeromaneuvering vehicle that is optimized for low Earth orbit sortie missions involving large, multiple plane-inclination changes. The aerothermal environment of the aerobraking vehicle is analyzed using state-of-the-art methods for nonequilibrium-radiative and convective heating that incorporate refinements unique to the configuration. The heating analysis of the aeromaneuvering vehicle required the development of a flowfield model for rarefied-hypersonic flow over a lifting surface at incidence. The predicted aerothermodynamic heating characteristics for both vehicles are correlated with thermal-control

Menees, Gene P.↗
NASA NTRS1985

Design and Performance Analysis of a Conical Aerobrake Orbital Transfer Vehicle Concept

A Shuttle-compatible systems design based on the core concept of attachable modules for the major vehicle components is proposed. The principal features include a disposable cargo/extra-propellant tank module; a porous, radiative, back-scattering drag-brake surface material of thin silica cloth; and a lightweight carbon-composite support structure. The mission payload capability for delivery, retrieval, and combined operations is determined for a broad range of missions including NASA/DOD requirements and extending through cislunar space. The effects of finite-rate surface catalysis, negative lift, and multiple atmospheric passes in reducing the aerothermodynamic heating rates are also investigated. In addition, the structural and thermal protection problems of the drag-brake support apparatus are analyzed, and recommendations are proposed for future design refinements.

Menees, Gene P.↗
NASA NTRS1985

Thermal Protection Requirements for Near-Earth Aeroassisted Orbital Transfer Vehicle Missions

The thermal protection required for decelerating and maneuvering spacecraft by aerodynamic forces is determined for return missions from geosynchronous to low Earth orbits. The effect of vehicle configuration on surface heating rates and selection of heat shield materials is analyzed. The effects of the current widespread estimates in the structure of atmospheric density are also evaluated. It is shown that nonequilibrium radiation can be a major source of surface heating during atmospheric entry and a significant factor for heat shielding requirements. It is also demonstrated that drag-brake concepts have application to a broad range of orbital transfer missions because of the favorable tradeoffs with aeromaneuvering vehicles in volumetric efficiency, retrothrust plane-change capability, and heat protection requirements. In addition, the results of this study indicate that the aeroassist technique produces acceptable penalties in vehicle payload capacity for drag-brake concepts, because of the system's heat protection requirements, and is highly attractive relative to all-propulsive orbital change maneuvers.

Menees, Gene P.↗
NASA NTRS1976

Nitric Oxide Formation by Meteoroids in the Upper Atmosphere

The process of nitric oxide formation during atmospheric entry of meteoroids is analyzed theoretically. An ablating meteoroid is assumed to be a point source in a uniform flow with a continuum regime evolving in its wake. The amount of nitric oxide produced by high-temperature reactions of air in the continuum regime is calculated by numerical integration of chemical-rate equations. This is accomplished by assuming that flow properties are constant across the reacting region, the radius of the region being determined from considerations of shock-wave formation and molecular diffusion. The results, when summed over the observed mass, velocity, and entry-angle distributions of meteoroids, provide annual global production rates of nitric oxide as a function of altitude. The peak production of nitric oxide is found to occur at altitudes between 9 x 10(exp 4) and 10(exp 5) m, the total annual rate being about 4 x 10(exp 7) kg. The present results suggest that the large concentration of nitric oxide observed below 9.5 x 10(exp 4) m could be attributed to meteoroids instead of photodissociation of nitrogen into metastable, 2D-state atoms, as has been previously hypothesized.

Menees, Gene P.↗
NASA NTRS1961

Aerodynamic Loads at Mach Numbers from 0.70 to 2.22 on an Airplane Model Having a Wing and Canard of Triangular Plan Form and Either Single or Twin Vertical Tails: Tabulated Data for the Model with Twin Vertical Tails - Supplement 2

Tabulated results of a wind-tunnel investigation of the aerodynamic loads on a canard airplane model with twin vertical tails are presented for Mach numbers from 0.70 to 2.22. The Reynolds number for the measurements was 2.9 x 10(exp 6) based on the wing mean aerodynamic chord. The results include local static-pressure coefficients measured on the wing, body, and one of the vertical tails for angles of attack from -4 degrees to 16 degree angles of sideslip of 0 degrees and 5.3 degrees, and nominal canard deflections of O degrees and 10 degrees. Also included are section force and moment coefficients obtained from integrations of the local pressures and model-component force and moment coefficients obtained from integrations of the section coefficients. Geometric details of the model are shown and the locations of the pressure orifices are shown. An index to the data contained herein is presented and definitions of nomenclature are given. Detailed descriptions of the model and experiments and a brief discussion of some of the results are given. Tabulated results of measurements of the aerodynamic loads on the same canard model but having a single vertical tail instead of twin vertical tails are presented.

Peterson, Victor L.↗
NASA NTRS1961

Aerodynamic Loads at Mach Numbers from 0.70 to 2.22 on a Airplane Model Having a Wing and Canard of Triangular Plan Form and Either Single or Twin Vertical Tails

Results of an investigation of the aerodynamic loads on a canard airplane model are presented without detailed analysis for the Mach number range of 0.70 t o 2.22. The model consisted of a triangular wing and canard of aspect ratio 2 mounted on a Sears-Haack body of fineness ratio 12.5 and either a single body-mounted vertical tail or twin wing mounted vertical tails of low aspect ratio and sweptback plan form. The body, right wing panel, single vertical tail, and left twin vertical tail were instrumented for measuring pressures. Data were obtained for angles of attack ranging from -4 degrees to +16 degrees, nominal canard deflection angles of 0 degrees and 10 degrees, and angles of sideslip of 0 degrees and 5.3 degrees. The Reynolds number was 2.9 x 10(exp 6) based on the wing mean aerodynamic chord. Selected portions of the data are presented in graphical form and attention is directed to some of the results of the investigation. All of the experimental results have been tabulated in the form of pressure coefficients and integrations of the pressure coefficients and are available as supplements to this paper. A brief summary of the contents of the tabular material is given.

Peterson, Victor L.↗
NASA NTRS1961

Aerodynamic Loads at Mach Numbers from 0.70 to 2.22 on an Airplane Model Having a Wing and Canard of Triangular Plan Form and Either Single or Twin Vertical Tails Supplement I-Tabulated Data for the Model with Single Vertical Tails: Tabulated Data for the Model with Single Vertical Tail - Supplement 1

Tabulated results of a wind-tunnel investigation of the aerodynamic loads on a canard airplane model with a single vertical tail are presented for Mach numbers from 0.70 to 2.22. The Reynolds number for the measurements was 2.9 x 10(exp 6) based on the wing mean aerodynamic chord. The results include local static pressure coefficients measured on the wing, body, and vertical tail for angles of attack from -4 deg to + 16 deg, angles of sideslip of 0 deg and 5.3 deg, vertical-tail settings of 0 deg and 5 deg, and nominal canard deflections of 0 deg and 10 deg. Also included are section force and moment coefficients obtained from integrations of the local pressures and model-component force and moment coefficients obtained from integrations of the section coefficients. Geometric details of the model and the locations of the pressure orifices are shown. An index to the data contained herein is presented and definitions of nomenclature are given.

Peterson, Victor L.↗
NASA NTRS1959

An Experimental Investigation of the Effect of a Canard Control on the Lift, Drag, and Pitching Moment of an Aspect-Ratio 2.0 Triangular Wing Incorporating a Form of Conical Camber

The results of an experimental investigation to determine the effect of a canard control on the lift, drag, and pitching-moment characteristics of an aspect-ratio-2.0 triangular wing incorporating a form of conical camber are presented. The canard had a triangular plan form of aspect ratio 2.0 and was mounted in the extended chord plane of the wing. The ratio of the area of the exposed canard panels to the total wing area was 6.9 percent, and the ratio of the total areas was 12.9 percent. Data were obtained at Mach numbers from 0.70 to 2.22 through an angle-of-attack range from -6 deg to +18 deg with the canard on, and with the canard off. To provide a basis for comparison, the canard was also tested with a symmetrical wing having the same plan form, aspect ratio, and thickness distribution as the cambered wing. The results of the investigation showed that at the high subsonic speeds the gain in maximum lift-drag ratio achieved by camber was considerably reduced by the addition of a canard. At the supersonic speeds, the addition of the canard did not change the effect of camber on the maximum lift-drag ratios.

Menees, Gene P.↗
NASA NTRS1959

Static Longitudinal Stability and Control Characteristics of an Unswept Wing and Unswept Horizontal-Tail Configuration at Mach Numbers from 0.70 to 2.22

Results of an investigation of the static longitudinal stability and control characteristics of an aspect-ratio-3.1, unswept wing configuration equipped with an aspect-ratio-4, unswept horizontal tail are presented without analysis for the Mach number range from 0.70 to 2.22. The hinge line of the all-movable horizontal tail was in the extended wing chord plane, 1.66 wing mean aerodynamic chords behind the reference center of moments. The ratio of the area of the exposed horizontal-tail panels to the total area of the wing was 13.3 percent and the ratio of the total areas was 19.9 percent. Data are presented at angles of attack ranging"from -6 deg to +18 deg for the horizontal tail set at angles ranging from +5 deg to -20 deg and for the tail removed.

Peterson, Victor L.↗