Search NASA⌕ Search

Engineering topics

Milad Mahzari

Publications and source records attributed to Milad Mahzari.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Mars Entry Instrumentation Flight Data and Mars 2020 Entry Environments

On February 18th, 2021, the Mars 2020 entry vehicle delivered the Perseverance rover to the surface of Mars. The entry vehicle carried a set of instrumentation installed on the heatshield and backshell to measure aerodynamic and aerothermal performance, named the Mars Entry, Descent, and Landing Instrumentation 2. This set of instrumentation included pressure transducers, thermocouples, heatflux sensors, and a radiometer, as well as a dedicated sensor support electronics system. All MEDLI2 hardware operated as expected during cruise and entry. MEDLI2 sensors gathered accurate pressure measurements in hypersonic through supersonic regimes to reconstruct vehicle attitude and atmospheric profiles. MEDLI2 on the heatshield sensors indicated that surface temperatures, caused by turbulent heating beginning 70 seconds after entry, remained at or below 1430 °C, while heatshield bondline temperatures rose less than 45 °C. Backshell surface TPS temperatures peaked at 630 °C, which was caused primarily by radiative heating measured by several separate sensors. The MEDLI2 temperature and pressure measurements enabled further detailed characterization of the Mars 2020 entry performance, and the flight dataset will provide a wealth of information for the EDL community and future mission designers.

thermal protection system↗
NASA NTRS2020

TPS and Entry System Technologies for Future Mars and Titan Exploration

The purpose of this white paper is to provide an overview to the NRC Decadal Survey Mars and Ocean Worlds Sub-Panels on thermal protection system (TPS) technologies required for future Mars and Titan exploration missions. It considers the capability of heritage TPS technology used by previous Mars and Titan missions. A prime conclusion is that there are important advances regarding the availability of forebody TPS therefore, we recommend that NASA invest in a cross-cutting technology program that focuses on development and sustainment of relevant TPS materials, entry systems, test facilities, design tools, and flight instrumentation.

Thermal protection systems↗
NASA NTRSDate not supplied

TPS and Entry Systems Technologies for Future Mars and Titan Exploration

During the past twenty years, NASA effectively erased earlier Mars mishaps with six successful missions to the Red Planet. These missions delivered one orbiter and five payloads to the surface. Those payloads included three rovers, Spirit (2004) which roamed 11 years, Opportunity (2004) which roamed nearly 15 years, and Curiosity (2012) which is in its ninth year, along with two landers, Phoenix (2008) and InSIGHT (2018). In July, the Mars 2020 mission will send another large rover, Perseverance, which will land in 2021. The InSIGHT mission even demonstrated the capability to send CubeSats along to help with communication back to the surface. NASA has demonstrated the capability to land a metric ton of vehicles plus science instruments on Mars and expects that the same technologies will be equally successful landing Dragonfly on Titan in the 2030’s. The thermal protection systems (TPS) used on the Mars missions are sufficiently developed and matured to continue furthering science on both Mars and Titan, assuming that the TPS materials are sustained by industry. The purpose of this white paper is to encourage further exploration and science on both Mars and Titan because we have the technologies to support them. In addition, we will look forward to human exploration of Mars and identify the improvements in TPS materials required to facilitate landing the larger payloads.

Thermal Protection Systems↗
NASA NTRSDate not supplied

Mars 2020 Thermal Protection Systems Sizing and Development

The Mars 2020 spacecraft delivering the Perseverance Rover to Mars was planned to be a build-to-print repeat of the Mars Science Laboratory (MSL) spacecraft that delivered the Curiosity Rover to Mars in 2012. The 2020 mission would deliver a slightly higher mass at a lower entry velocity, so the mission designers were comfortable with the cost saving approach of using an already proven design. The approach used in sizing the thermal protection systems (TPS) for the various components of the MSL spacecraft included convective heating and shock layer radiation (a small contributor) on the heatshield and only convective heating on all of the aft body parts. At the time, it was assumed that the contribution of radiation from the shock layer and the wake was negligible on the aft body at Mars. In the time since the MSL spacecraft was designed, in light of new data and analysis, NASA realized the significance of radiative heating in the aftbody on vehicles entering Mars, beginning with the InSight entry. New analyses showed that the radiant heat fluxes on aft body components at Mars were of the same order or even larger than predicted convective heat fluxes. The Mars 2020 team was tasked with showing that the TPS thicknesses designed for MSL with only convective heating would survive the Mars 2020 convective plus radiative heat flux environments. Luckily, many of the MSL aft body components were sized using an extra conservative approach, often sizing for the worst environment at the lightest, thinnest structure, even though the environments and structures were not co-located. The Mars 2020 team had to more accurately evaluate the environments and structures to show that the design would close

Mars Entry↗
NASA NTRSDate not supplied

MEDLI2: Ablator Models for Flight

During the entry of Mars Science Laboratory (MSL) the heatshield was equipped with the instrumentation suite Mars Entry, Descent, and Landing Instruments (MEDLI). In-depth thermocouple (TC) data was used to reconstruct the surface heating[1,2]. Discrepancies between MEDLI’s flight heating data and predicted thermal response and recession[3] led to a campaign to characterize and test Mars2020 and MEDLI2 (Mars Entry, Descent, and Landing Instrument 2)[4] flight-lot thermal protection materials (TPS) at relevant ground test conditions. This paper covers the development and validation of flight-lot material response models for the heatshield material Phenolic Impregnated Carbon Ablator (PICA) and the backshell material SLA-561V (Super Lightweight Ablator). Virgin and char properties such as thermal conductivity and emissivity were updated as a function of temperature and pressure in the MEDLI2 specific material response models. Other material properties were characterized and determined to be similar to prior TPS material measurements used for the heritage models. MEDLI2 also investigated the impact of the protective coating that was applied to MSL and Mars2020’s PICA heatshield to reduce the particulate matter shedding. Evidence from arc jet experiments on coated PICA showed that although there were no adverse effects on the performance of the TPS, there were differences in the in-depth temperatures and reduced recession compared to material response predictions of uncoated PICA.[5,6]. Fully Implicit Ablation and Thermal response (FIAT)[7] material response simulations were conducted with the heritage and MEDLI2 flight-lot material models. FIAT-predicted in-depth temperature responses and recession predictions were compared to flight-lot certification ground-test arc jet test data and MEDLI2 thermocouple data.

Materials Response↗
NASA NTRSDate not supplied

Inverse Estimation of Mars 2020 Entry Aeroheating Environments Using MEDLI2 Flight Data

The Mars Entry, Descent, and Landing Instrumentation 2 (MEDLI2) sensor suite collected heating and pressure data during entry into Mars' atmosphere of the Mars 2020 Perseverance rover. MEDLI2 included thermocouples, heat flux sensors, and pressure transducers on both the heatshield and the backshell. This paper covers the inverse estimation of heatshield and backshell surface heating based on the MEDLI2 Instrumented Sensor Plugs (MISPs), a network of thermocouples embedded in thermal protection system plugs across the aeroshell. Monte Carlo analysis was conducted to assess the sensitivity of the surface heat rate and temperature to uncertainties in thermocouple depth and material properties such as density, specific heat capacity, and thermal conductivity. Data from each MISP was also used to estimate the local time of transition from laminar to turbulent flow at each plug location.

Hannah S Alpert↗
NASA NTRSDate not supplied

Mars 2020 Reconstructed Aerothermal Environments and Design Margins

The Mars 2020 aeroshell's thermal protection system was nearly identical to the Mars Science Laboratory system that successfully completed its mission for the Curiosity rover's landing in 2012. It was predicted that, like Mars Science Laboratory, the Mars 2020 heatshield would experience boundary layer transition and that the thermal protection system would provide sufficient material thickness margins against the aerothermal environments, even after adding radiative heating that was not included for Mars Science Laboratory. The Mars 2020 flight instrumentation suite included heatshield sensors similar to Mars Science Laboratory and new backshell measurements. A full set of surface pressure and in-depth temperature data were collected during atmospheric entry. This paper provides an initial analysis of the flight data and focuses on the reconstructed total surface heat flux inferred from the measured temperatures. Turbulent boundary layer conditions again were observed on the Mars 2020 heatshield, and the temperatures at all eleven heatshield and six backshell thermocouple in-depth sensor locations were well within system capabilities due to favorable entry conditions and conservative uncertainties. New computational fluid dynamics results on the reconstructed entry trajectory are compared to the measured surface pressures and reconstructed total heat fluxes. The predicted heatshield surface pressures at six locations match the data qualitatively and quantitatively well, as expected. Smooth-wall laminar heating predictions prior to boundary layer transition fall above the reconstructed heating on the heatshield. After the observed boundary layer transition time, total heat flux based on algebraic turbulence model calculations generally match the heat flux trends relative to one another. The convective heat flux was predicted to constitute the majority of the total heating. On the backshell, smooth-wall laminar total heat flux predictions generally exceed the reconstructed total heating at six locations. At each of these locations, it is estimated that radiative heating provided almost all of the total heating. The Mars 2020 as-flown aerothermal environments were well below the design levels for all measurement locations due to conservative design assumptions and a stressing design trajectory.

Mars 2020↗
NASA NTRSDate not supplied

MEDLI2 Material Response Model Development and Validation

During the entry of Mars Science Laboratory (MSL) the heatshield was equipped with the instrumentation suite Mars Entry, Descent, and Landing Instruments (MEDLI). In-depth thermocouple (TC) data was used to reconstruct the surface heating and temperatures. Discrepancies between MEDLI’s recorded in-depth heating data and the predicted thermal response and recession led to a campaign to characterize and test Mars Entry, Descent, and Landing Instrument 2 (MEDLI2) flight lot thermal protection materials (TPS) at relevant temperatures and pressures for Martian entry conditions. This paper covers the development and validation of MEDLI2 flight lot material response models for the heatshield material Phenolic Impregnated Carbon Ablator (PICA) and the backshell material Super-Lightweight Ablator (SLA-561V). Virgin and char thermal conductivities were updated as a function of temperature and pressure in the MEDLI2 specific material response models. Other material properties such as virgin and char density, emissivity, absorptivity, and specific heat capacitance was also characterized and compared to the “Heritage” models used during the TPS design phase of Mars 2020. Fully Implicit Ablation and Thermal response (FIAT) simulations were completed using the Heritage and MEDLI2 material response models to provide evidence of the increased accuracy of the MEDLI2 model. FIAT predicted in-depth temperatures were compared to flight lot certification ground-test arc jet test data and MEDLI2 flight thermocouple data.

Material response↗
NASA NTRSDate not supplied

Mars 2020 Reconstructed Aerothermal Environments and Design Margins

The Mars 2020 aeroshell's thermal protection system was nearly identical to the Mars Science Laboratory system that successfully completed its mission for the Curiosity rover's landing in 2012. It was predicted that, like Mars Science Laboratory, the Mars 2020 heatshield would experience boundary layer transition and that the thermal protection system would provide sufficient material thickness margins against the aerothermal environments, even after adding radiative heating that was not included for Mars Science Laboratory. The Mars 2020 flight instrumentation suite included heatshield sensors similar to Mars Science Laboratory and new backshell measurements. A full set of surface pressure and in-depth temperature data were collected during atmospheric entry. This paper provides an initial analysis of the flight data and focuses on the reconstructed total surface heat flux inferred from the measured temperatures. Turbulent boundary layer conditions again were observed on the Mars 2020 heatshield, and the temperatures at all eleven heatshield and six backshell thermocouple in-depth sensor locations were well within system capabilities due to favorable entry conditions and conservative uncertainties. New computational fluid dynamics results on the reconstructed entry trajectory are compared to the measured surface pressures and reconstructed total heat fluxes. The predicted heatshield surface pressures at six locations match the data qualitatively and quantitatively well, as expected. Smooth-wall laminar heating predictions prior to boundary layer transition fall above the reconstructed heating on the heatshield. After the observed boundary layer transition time, total heat flux based on algebraic turbulence model calculations generally match the heat flux trends relative to one another. The convective heat flux was predicted to constitute the majority of the total heating. On the backshell, smooth-wall laminar total heat flux predictions generally exceed the reconstructed total heating at six locations. At each of these locations, it is estimated that radiative heating provided almost all of the total heating. The Mars 2020 as-flown aerothermal environments were well below the design levels for all measurement locations due to conservative design assumptions and a stressing design trajectory.

Mars 2020↗
NASA NTRSDate not supplied

Mars Entry Instrumentation Flight Data and Mars 2020 Entry Environments

On February 18th, 2021, the Mars 2020 entry vehicle delivered the Perseverance rover to the surface of Mars. The entry vehicle carried a set of instrumentation installed on the heatshield and backshell to measure aerodynamic and aerothermal performance, named the Mars Entry, Descent, and Landing Instrumentation 2. This set of instrumentation included pressure transducers, thermocouples, heatflux sensors, and a radiometer, as well as a dedicated sensor support electronics system. All MEDLI2 hardware operated as expected during cruise and entry. MEDLI2 sensors gathered accurate pressure measurements in hypersonic through supersonic regimes to reconstruct vehicle attitude and atmospheric profiles. MEDLI2 on the heatshield sensors indicated that surface temperatures, caused by turbulent heating beginning 70 seconds after entry, remained at or below 1430 °C, while heatshield bondline temperatures rose less than 45 °C. Backshell surface TPS temperatures peaked at 630 °C, which was caused primarily by radiative heating measured by several separate sensors. The MEDLI2 temperature and pressure measurements enabled further detailed characterization of the Mars 2020 entry performance, and the flight dataset will provide a wealth of information for the EDL community and future mission designers.

thermal protection systems↗
NASA NTRSDate not supplied

MEDLI2: MISP Inferred Aerothermal Environment and Flow Transition Assessment

The Mars Entry, Descent, and Landing Instrumentation 2 (MEDLI2) sensor suite on the Mars2020 mission contained multiple sensors on the aeroshell to measure the aerothermal environment during entry into the Martian atmosphere. These sensors performed superbly and successfully returned forebody and aftbody heating measurements. Analysis of MEDLI2 data indicated flow transitioning from a laminar to turbulent state on the heatshield. No evidence of flow transition was observed on the backshell. Two methods were used to estimate flow transition times on the heatshield: (1) temperature gradient of near-surface thermocouple data and (2) heat flux gradient from an inverse reconstruction approach using thermocouple data and material response modeling. Both methods produced similar transition times with an estimated accuracy of ±1 s. To assess various transition criteria, transition parameters were evaluated at each sensor location using flow field solutions from computational fluid dynamics (CFD) simulations. The idea was to use conservative values inferred from MEDLI2 data as transition criteria for other Mars missions. To test this hypothesis, MEDLI data from the Mars Science Laboratory (MSL) mission was used to compare predicted vs. actual flow transition times. The comparisons suggest smooth wall transition criteria are not well-suited in modeling the rapid progression of a turbulent transition front. Transition criteria containing a roughness element parameter agreed better with the flight data. In summary, critical transition values derived from MEDLI2 data may be used as a starting point in constructing a flow transition model for future Mars missions.

Chun Y Tang↗
NASA NTRSDate not supplied

Development and Sizing of the Mars 2020 Thermal Protection System

The Mars 2020 entry vehicle successfully delivered the Perseverance rover to the Martian surface on 18 February 2021. The entry vehicle aeroshell was shielded from aerodynamic heating with a thermal protection system (TPS) made of three different ablative materials. This paper provides an overview of the methodology and assumptions employed for the thermal sizing and design of the Mars 2020 aeroshell TPS. The sizing results demonstrate that the as-built thicknesses of the TPS materials were sufficient to withstand the predicted aerothermal environments without exceeding temperature limits of the underlying aeroshell structure. This paper also provides an overview of the ground testing performed in NASA arc jet facilities to verify the performance of flight lot TPS materials. Finally, temperature data returned by thermocouples embedded in the flight vehicle TPS are compared with predictions by the thermal response models used in pre-flight TPS sizing.

Mars2020↗
NASA NTRSDate not supplied

Lessons Learned from Aerothermal Flight Data on NASA Mars Entry Vehicles

The NASA Mars Science Laboratory (MSL) and Mars 2020 entry vehicles included temperature measurements inside and direct heat flux on the surface of the thermal protection system (TPS) material. The instrumentation was included to begin addressing predictive capabilities for aerodynamic heating and ablative TPS material response. The MSL aeroshell included temperature measurements at seven heatshield locations, from which total aerodynamic heating was reconstructed. The Mars 2020 instrumentation suite included eleven heatshield measurement locations and new backshell measurements at nine locations: six with temperature sensors, two with sensors to directly measure total heat flux, and one to measure radiative heat flux. Both instrumentation suites returned full sets of data, with all temperature sensors nearest to the surface surviving entry, indicating minimal material recession. Heatshield boundary layer transition (BLT) was observed for both vehicles prior to the time of peak heating, with transition starting near the shoulder and progressing towards the stagnation area. MSL’s higher speed on approach to Mars resulted in higher total heating compared to Mars 2020, with the maximum occurring near the heatshield’s leeside shoulder. The Mars 2020 backshell heating data indicate significant contributions from shock layer radiation. Heating from Navier-Stokes flowfield calculations are in family with reconstructed heating. The paper covers the instrumentation, BLT and reconstructed heating on both heatshields, backshell heating for Mars 2020, TPS performance, and predicted versus reconstructed heat fluxes. Opportunities for improved design approaches for future Mars missions are discussed, especially for the upcoming Mars Sample Return mission.

Mars Science Laboratory↗
NASA NTRSDate not supplied

Lessons Learned from Aerothermal Flight Data on NASA Mars Entry Vehicles

The NASA Mars Science Laboratory (MSL) and Mars 2020 entry vehicles included temperature measurements inside and direct heat flux on the surface of the thermal protection system (TPS) material. The instrumentation was included to begin addressing predictive capabilities for aerodynamic heating and ablative TPS material response. The MSL aeroshell included temperature measurements at seven heatshield locations, from which total aerodynamic heating was reconstructed. The Mars 2020 instrumentation suite included eleven heatshield measurement locations and new backshell measurements at nine locations: six with temperature sensors, two with sensors to directly measure total heat flux, and one to measure radiative heat flux. Both instrumentation suites returned full sets of data, with all temperature sensors nearest to the surface surviving entry, indicating minimal material recession. Heatshield boundary layer transition (BLT) was observed for both vehicles prior to the time of peak heating, with transition starting near the shoulder and progressing towards the stagnation area. MSL’s higher speed on approach to Mars resulted in higher total heating compared to Mars 2020, with the maximum occurring near the heatshield’s leeside shoulder. The Mars 2020 backshell heating data indicate significant contributions from shock layer radiation. Heating from Navier-Stokes flowfield calculations are in family with reconstructed heating. The paper covers the instrumentation, BLT and reconstructed heating on both heatshields, backshell heating for Mars 2020, TPS performance, and predicted versus reconstructed heat fluxes. Opportunities for improved design approaches for future Mars missions are discussed, especially for the upcoming Mars Sample Return mission.

Mars Science Laboratory↗
NASA NTRSDate not supplied

Development and Sizing of the Mars 2020 Thermal Protection System

The Mars 2020 entry vehicle successfully delivered the Perseverance rover to the Martian surface on 18 February 2021. The entry vehicle aeroshell was shielded from aerodynamic heating with a thermal protection system (TPS) made of three different ablative materials. This paper provides an overview of the methodology and assumptions employed for the thermal sizing and design of the Mars 2020 aeroshell TPS. The sizing results demonstrate that the as-built thicknesses of the TPS materials were sufficient to withstand the predicted aerothermal environments without exceeding temperature limits of the underlying aeroshell structure. This paper also provides an overview of the ground testing performed in NASA arc jet facilities to verify the performance of flight lot TPS materials. Finally, temperature data returned by thermocouples embedded in the flight vehicle TPS are compared with predictions by the thermal response models used in pre-flight TPS sizing.

Mars2020↗