Search NASA⌕ Search

Engineering topics

Mitchell, T. E.

Publications and source records attributed to Mitchell, T. E..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Transient oxidation of single-crystal beta-NiAl

The transient oxidation of beta-NiAl in air at 800 C and 1100 C has been studied using electron microscopy. The oxide scale consists predominantly of metastable Al2O3 phases. Theta-Al2O3 is the major oxide phase within 10.0 hr of oxidation at 800 C and 0.1 hr at 1100 C. The scales form epitaxially on (001) sub beta and (012) sub beta specimens throughout the transient stage, whereas the degree of preferred oxide orientation decreases with oxidation time on (011) sub beta and (111) sub beta specimens. The orientation relationships reflect the small mismatch between parallel close-packed directions in the metal and in the cation sublattice of the oxides. The correlation of distinctive oxide surface morphologies with internal structural defects indicates the strong tendency of the Al2O3 scale to grow via short-circuit diffusion paths.

Doychak, J.↗
NASA NTRS1987

TEM investigation of beta-SiC grown epitaxially on Si substrate by CVD

A transmission electron microscopy study is being conducted on the microstructure of beta-SiC films grown epitaxially on 001-plane silicon by chemical vapor deposition. Observations have been made in plain view and in cross-section. A high density of stacking faults has been found in the bulk of the epilayer which are bounded by partials of the Shockley type with Burgers vectors 1/6 211-line. Cross-sectional high resolution electron microscopy of the interface has shown it to be semicoherent with misfit dislocations to accommodate the lattice parameter difference between the substrate and the epilayer. In addition to misfit dislocations, a high density of twins and some stacking faults are present in the SiC near the interface. Mechanisms for the nucleation and growth of these defects are discussed.

Chorey, C. M.↗
NASA NTRS1985

High temperature oxidation of beta-NiAl

The oxidation of single crystal beta-NiAl has been studied primarily using electron microscopy. Oriented metastable Al2O3 phases form during transient oxidation at 800 C. Specific orientation relationships exist on all metal orientations studied and are a result of the small mismatch along aligned close-packed directions in the cation sublattices of the metal and oxide. Transformation of the metastable Al2O3 phases at 1100 C results in an oxide morphology described as the 'lacey' structure of alpha-Al2O3 scales. This structure results from impingement of oriented patches of alpha-Al2O3 as the transformation initiates and moves radially parallel to the surface. Scale growth occurs by diffusion along high angle grain boundaries. A drastic reduction in oxidation rate accompanies the change in oxide morphology.

Koychak, J. K.↗
NASA NTRS1985

Microstructural aspects of zirconia thermal barrier coatings

Various combination of plasma-sprayed bond coatings and zirconia ceramic coatings on a nickel-based superalloy substrate were tested by static thermal exposure at 1200 C and cyclic thermal exposure to 1000 C. The bond coats were based on Ni-Cr-Al alloys with additions of rare earth elements and Si. The ceramic coats were various ZrO2-Y2O3 compositions, of which the optimum was found to be ZrO2-8.9 wt percent Y2O3. Microstructural analysis showed that resistance to cracking during thermal exposure is strongly related to deleterious phase changes. Zones depleted of Al formed at the bond coat/ceramic coat interface due to oxidation and at the bond coat/substrate interface due to interdiffusion, leading eventually to breakdown of the bond coat. The 8.9 percent Y2O3 coating performed best because the as-sprayed metastable tetragonal phase converted slowly into the low-Y2O3 tetragonal plus high-Y2O3 cubic-phase mixture, so that the deleterious monoclinic phase was inhibited from forming. Failure appeared to start with the formation of circumferential cracks in the zirconia, probably due to compressive stresses during cooling, followed by the formation of radial cracks due to tensile stresses during heating. Cracks appeared to initiate at the Al2O3 scale/bond coat interface and propagate through the zirconia coating. Comparisons were made with the behavior of bulk ZrO2-Y2O3 and the relationship between the microstructure of the tetragonal phase and the phase diagram. A separate investigation was also made of the ZrO2-Al2O3 interface.

Mitchell, T. E.↗
NASA NTRS1984

Bubble formation in oxide scales on SiC

The oxidation of alpha-SiC single crystals and sintered alphaand beta-SiC polycrystals has been investigated at elevated temperatures. Bubble formation is commonly observed in oxide scales on polycrystalline SiC, but is rarely found on single-crystal scales; bubbles result from the preferential oxidation of C inclusions, which are abundant in SiC polycrystals. The absence of bubbles on single crystals, in fact, implies that diffusion of the gaseous species formed on oxidation, CO (or possibly SiO), controls the rate of oxidation of SiC.

Mieskowski, D. M.↗
NASA NTRS1981

Microstructure and mechanical properties of bulk yttria-partially-stabilized zirconia

A commercially available bulk 4.5 mole percent yttria-Y2O3)-partially-stabilized zirconia (PSZ) was studied by light microscopy, X-ray analysis, microhardness measurement, and fracture toughness testing. The growth of the precipitates and the phase transformations were studied as a function of aging in air at 1500 C. Aging cuves were constructed for both the as-received and the solution-annealed-and-quenched materials; the curves showed hardness peaks at 1397 and 1517 kg/sq mm, respectively. A total of twelve different types of tetragonal precipitates were found. The rectangular plate-shaped tetragonal precipitates were found to have a (110) habit plane. Grinding of the Y2O3 PSZ into powder did not cause a significant amount of metastable tetragonal precipitates to transform into the monoclinic phase, thus indicating that transformation toughening is not a significant mechanism for the material. The fracture toughness of the aged and of the unaged solution-annealed-and-quenched PSZ was found to be between 2 and 3 MN/cu m/2.

Valentine, P. G.↗
NASA NTRS1981

Microstructure and mechanical properties of bulk yttria-partially-stabilized zirconia

A commercially available bulk 4.5 mole percent yttria-(Y2O3) partially stabilized zirconia (PSZ) was studied by light microscopy, X-ray analysis, microhardness measurement, and fracture toughness testing. The growth of the precipitates and the phase transformations were studied as a function of aging in air at 1500 C. Aging curves were constructed for both the as received and the solution annealed and quenched materials; the curves showed hardness peaks at 1397 and 1517 Kg/sq mm respectively. The rectangular plate shaped tetragonal precipitates were found to have a 110 habit plane. A total of twelve different types of tetragonal precipitates were found. Grinding of the Y2O3 PSZ into powder did not cause a significant amount of metastable tetragonal precipitates to transform into the monoclinc phase, thus indicating that transformation toughening is not a significant mechanism for the material.

Valentine, P. G.↗
NASA NTRS1978

Beta-to-alpha transformation in polycrystalline SiC. II - Interfacial energetics

A phenomenological analysis of the energetics of the beta-to-alpha transformation in polycrystalline SiC is presented. It is found that the extreme anisotropy of the interfacial energy between alpha- and beta-SiC can account for the rapid growth of composite grains into the beta matrix during conventional sintering or hot-pressing processes. The composite grains consist of alpha-SiC plates 'sandwiched' between well-oriented and recrystallized beta-SiC 'envelopes'. The interfaces involving the 111 plane type of beta and (0001) of alpha have much lower energies than random beta/alpha interfaces.

Mitchell, T. E.↗