Search NASA⌕ Search

Engineering topics

Morgan, Dane

Publications and source records attributed to Morgan, Dane.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

X-Ray Diffraction and Electron Microscopy Studies of the Size Effects on Pressure-Induced Phase Transitions in CdS Nanocrystals

In recent years, investigations of the phase transition behavior of semiconducting nanoparticles under high pressure has attracted increasing attention due to their potential applications in sensors, electronics, and optics. However, current understanding of how the size of nanoparticles influences this pressure-dependent property is somewhat lacking. In particular, phase behaviors of semiconducting CdS nanoparticles under high pressure have not been extensively reported. Therefore, in this work, CdS nanoparticles of different sizes are used as a model system to investigate particle size effects on high-pressure-induced phase transition behaviors. In particular, 7.5, 10.6, and 39.7 nm spherical CdS nanoparticles are synthesized and subjected to controlled high pressures up to 15 GPa in a diamond anvil cell. Analysis of all three nanoparticles using in-situ synchrotron wide-angle X-ray scattering (WAXS) data shows that phase transitions from wurtzite to rocksalt occur at higher pressures than for bulk material. Bulk modulus calculations not only show that the wurtzite CdS nanomaterial is more compressible than rocksalt, but also that the compressibility of CdS nanoparticles depends on their particle size. Furthermore, sintering of spherical nanoparticles into nanorods was observed for the 7.5 nm CdS nanoparticles. Our results provide new insights into the fundamental properties of nanoparticles under high pressure that will inform designs of new nanomaterial structures for emerging applications.

Meng, Lingyao↗
DOE OSTI2020

An Unexpected Role of H During SiC Corrosion in Water

During aqueous corrosion, atoms in the solid react chemically with oxygen, leading either to the formation of an oxide film or to the dissolution of the host material. Commonly, the first step in corrosion involves an oxygen atom from the dissociated water that reacts with the surface atoms and breaks near-surface bonds. In contrast, hydrogen on the surface often functions as a passivating species. Here, we discovered that the roles of O and H are reversed in the early corrosion stages on a Si-terminated SiC surface. O forms stable species on the surface, and chemical attack occurs by H that breaks the Si–C bonds. Here, this so-called hydrogen scission reaction is enabled by a newly discovered metastable bridging hydroxyl group that can form during water dissociation. The Si atom that is displaced from the surface during water attack subsequently forms H 2 SiO 3 , which is a known precursor to the formation of silica and silicic acid. This study suggests that the roles of H and O in oxidation need to be reconsidered.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Shape Dependence of Pressure-Induced Phase Transition in CdS Semiconductor Nanocrystals

Understanding structural stability and phase transformation of nanoparticles under high pressure is of great scientific interest, as it is one of the crucial factors for design, synthesis, and application of materials. Even though high-pressure research on nanomaterials has been widely conducted, their shape-dependent phase transition behavior still remains unclear. Examples of phase transitions of CdS nanoparticles are very limited, despite the fact that it is one of the most studied wide band gap semiconductors. Here we have employed in-situ synchrotron wide-angle X-ray scattering (WAXS) and transmission electron microscopy (TEM) to investigate the high-pressure behaviors of CdS nanoparticles as a function of particle shapes. We observed that CdS nanoparticles transform from wurtzite to rocksalt phase at elevated pressure in comparison to their bulk counterpart. Phase transitions also vary with particle shape—rod-shaped particles show a partially reversible phase transition and the onset of the structural phase transition pressure decreases with decreasing surface-to-volume ratios, while spherical particles undergo irreversible phase transition with relatively low phase transition pressure. Additionally, TEM images of spherical particles exhibited sintering-induced morphology change after high-pressure compression. Calculations of the bulk modulus reveals that spheres are more compressible than rods in the wurtzite phase. These results indicate that the shape of the particle plays an important role in determining their high-pressure properties. Our study provides important insights into understanding of the phase-structure-property relationship, guiding future design and synthesis of nanoparticles for promising applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The incommensurately modulated structures of low-temperature labradorite feldspars: a single-crystal X-ray and neutron diffraction study

Labradorite feldspars of the plagioclase solid solution series have been known for their complicated subsolidus phase relations and enigmatic incommensurately modulated structures. Characterized by the irrationally indexed e -reflections in the diffraction pattern, e -labradorite shows the largest variation in the incommensurate ordering states among the e -plagioclase structures. The strongly ordered low-temperature e -labradorite is one of the last missing pieces of the e -plagioclase puzzle. Nine plutonic and metamorphic labradorite feldspar samples from Canada, Ukraine, Minnesota (USA), Tanzania and Greenland with compositions ranging from An 52.5 to An 68 were studied with single-crystal X-ray diffraction. Two crystals from Labrador, Canada, and Duluth, MN, USA, with wide enough twin lamellae were analyzed with single-crystal neutron diffraction. The incommensurately modulated structures of e -plagioclase are refined for the first time with neutron diffraction data, which confirmed that the T—O distance modulation in the low-temperature e -plagioclase results from the Al–Si ordering in the framework. Detailed configurations of the M site are also observed in the structures refined from neutron diffraction data, which were not possible to see with X-ray diffraction data. The relation between the q -vectors and the mole% An composition is revealed for the entire compositional range of e -plagioclase, from An 25 to An 75 . The previously proposed two-trend relation depending on the cooling rate and phase transition path is confirmed. A new classification of e -plagioclase ( e α , e β and e γ ) is proposed based on the q -vector of the structure, which makes it an independent character from the presence/absence of density modulation. New parameters are proposed to quantify the ordering states of these complicated aperiodic structures of e -plagioclases, such as the difference between $\langle$T 1 o—O$\rangle$ and $\langle$T 1 m—O$\rangle$ at phase t = 0.2 or the normalized intensity of the (071\bar 1) reflection.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Protective cathode coatings for lithium-ion batteries

Cathode coatings for lithium ion batteries, cathodes coated with the coatings, and lithium ion batteries incorporating the coated cathodes are provided. The coatings, which are composed of binary, ternary, and higher order metal oxides and/or metalloid oxides, can reduce the hydrofluoric acid (HF)-induced degradation of the electrolyte and/or cathodes, thereby improving the performance of lithium ion batteries, relative to lithium ion batteries that employ bare cathodes.

Aykol, Muratahan↗
DOE OSTI2019

Materials Discovery of Stable and Nontoxic Halide Perovskite Materials for High‐Efficiency Solar Cells

Abstract Two critical limitations of organic–inorganic lead halide perovskite materials for solar cells are their poor stability in humid environments and inclusion of toxic lead. In this study, high‐throughput density functional theory (DFT) methods are used to computationally model and screen 1845 halide perovskites in search of new materials without these limitations that are promising for solar cell applications. This study focuses on finding materials that are comprised of nontoxic elements, stable in a humid operating environment, and have an optimal bandgap for one of single junction, tandem Si‐perovskite, or quantum dot–based solar cells. Single junction materials are also screened on predicted single junction photovoltaic (PV) efficiencies exceeding 22.7%, which is the current highest reported PV efficiency for halide perovskites. Generally, these methods qualitatively reproduce the properties of known promising nontoxic halide perovskites that are either experimentally evaluated or predicted from theory. From a set of 1845 materials, 15 materials pass all screening criteria for single junction cell applications, 13 of which are not previously investigated, such as (CH 3 NH 3 ) 0.75 Cs 0.25 SnI 3 , ((NH 2 ) 2 CH)Ag 0.5 Sb 0.5 Br 3 , CsMn 0.875 Fe 0.125 I 3 , ((CH 3 ) 2 NH 2 )Ag 0.5 Bi 0.5 I 3 , and ((NH 2 ) 2 CH) 0.5 Rb 0.5 SnI 3 . These materials, together with others predicted in this study, may be promising candidate materials for stable, highly efficient, and nontoxic perovskite‐based solar cells.

Jacobs, Ryan↗
DOE OSTI2019

New frontiers for the materials genome initiative

The Materials Genome Initiative (MGI) advanced a new paradigm for materials discovery and design, namely that the pace of new materials deployment could be accelerated through complementary efforts in theory, computation, and experiment. Along with numerous successes, new challenges are inviting researchers to refocus the efforts and approaches that were originally inspired by the MGI. In May 2017, the National Science Foundation sponsored the workshop “Advancing and Accelerating Materials Innovation Through the Synergistic Interaction among Computation, Experiment, and Theory: Opening New Frontiers” to review accomplishments that emerged from investments in science and infrastructure under the MGI, identify scientific opportunities in this new environment, examine how to effectively utilize new materials innovation infrastructure, and discuss challenges in achieving accelerated materials research through the seamless integration of experiment, computation, and theory. This article summarizes key findings from the workshop and provides perspectives that aim to guide the direction of future materials research and its translation into societal impacts.

36 MATERIALS SCIENCE↗