Search NASA⌕ Search

Engineering topics

Mueller, Juergen

Publications and source records attributed to Mueller, Juergen.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Mid-Air Helicopter Delivery at Mars Using a Jetpack

Mid-Air Helicopter Delivery (MAHD) is a new Entry, Descent and Landing (EDL) architecture to enable in situ mobility for Mars science at lower cost than previous rover missions. It uses a jetpack to slow down a Mars Science Helicopter (MSH) after separation from the backshell, and reach aerodynamic conditions suitable for helicopter take-off in mid air. MAHD's lander-free approach leaves enough room in the aeroshell to accommodate larger rotors. This drastically improves flight performance compared to heritage EDL approaches, notably +60\% science payload mass. MAHD also brings cost savings, a simpler architecture, improved surface access and can reach higher elevations on Mars. This paper introduces a design for the MAHD system architecture and operations. We present a mechanical configuration which fits both MSH and the jetpack within the 2.65-m Mars heritage aeroshell, and a jetpack control architecture which fully leverages the available helicopter avionics. We discuss preliminary numerical models of the flow dynamics resulting from the interaction between the jets, the rotors and the side winds. We define a force-torque sensing architecture capable of handling the wind and trimming the rotors to prepare for safe take-off. Finally, we analyze the dynamic environment and closed-loop control simulation results to demonstrate the preliminary feasibility of MAHD.

Balaram, J.↗
NASA NTRS2020

Innovative Thermal Management & Control to Surmount Challenges of Exploring Ocean Worlds on Europa and Enceladus

Probes to penetrate the thick ice shells of our solar system’s Ocean Worlds have been studied for nearly 20 years, since scientific evidence strongly suggested a subsurface ocean on the Jupiter moon called Europa. There is keen scientific interest in exploring four significant themes on such proposed missions: 1) Geodynamics, 2) Geochemistry, 3) Habitability, and 4) Life Detection. The ice shells of Ocean Worlds are predicted to be up to 40 km thick; they exhibit extreme thermal environments, with ice temperatures from 100 K to 270 K, and extreme pressure environments from vacuum to 53 MPa. Jet Propulsion Laboratory has conducted a broad-look investigation of proposed mission concepts to Europa to identify the significant technology and operational challenges of Europa ice-penetration. The thermal-mechanical system (TMS) of an ice penetration probe (IPP) designed to access the ocean of an icy moon using radioisotope thermoelectric generators for heat and power faces technological hurdles exacerbated by severe thermal and volume constraints. This study identified thermal management and control (TMC) challenges that are strongly linked to: ice penetration start-up, mobility and navigation in the ice, communications while in the ice sheet, and detecting and avoiding in-ice hazards. The major objectives of the TMC system are: 1) Absorb internal thermal energy from the IPP radioisotope power source, 2) Maintain liquid water conditions around the IPP at all times, 3) Manage and control thermal flows from probe nose to tail, and 4) Provide pressure containment for all internal probe components. This work discusses the baseline TMC system architecture and design developed to accomplish these objectives, and survive and transit the extreme ice thicknesses in pursuit of Icy/Ocean Worlds science goals. The proposed TMC system consisting of an internal pumped two-phase fluid loop “thermal bus” for thermal energy capture, variable conductance heat pipe system for passively adaptive thermal energy transport around the probe, and water jetting system for ice cutting is described and discussed. Critical testing performed to date is described.

Lee, Kuan-Lin↗
NASA NTRS2020

System Engineering a Solar Thermal Propulsion Mission Concept for Rapid Interstellar Medium Access

The interstellar medium (ISM) represents the next frontier in space exploration, with many new discoveries to be made. The challenge, being so far away from Earth, the ISM requires many decades to reach. To advance our knowledge of what exists beyond our Solar System, new approaches for rapid access are required. One such approach is solar thermal propulsion (STP). The approach uses several Venus and Earth gravity assists to fly to Jupiter and use its gravity well to dive towards the Sun. Approaching within 3 solar radii a perihelion burn would be performed, maximizing the spacecraft’s ΔV to achieve high Solar System escape velocities. A unique aspect of the STP mission concept is that the Sun is not only used as a gravity well for an Oberth manoeuvre, but also to heat the fuel to ultra-high-temperatures (>3000 K), enabling a monopropellant burn with high specific impulse (Isp). Prior preliminary studies indicated escape velocities of over 20 astronomical unit (AU)/yr would be possible. An in-depth modelling exercise was undertaken to determine how such a system would perform. The model in this paper showed the current STP design is capable of providing just under 9±1 AU/yr, but there are many technology developments that could increase escape velocity. The technologies vary from items that could be implemented in the near term, like turbo-pumps driven by the hydrogen, to items requiring more extensive development programs like thin coatings which do not erode in superheated hydrogen. After reviewing the STP approach, and comparing it to a solid rocket motor (SRM), it was found that with currently available technology, SRM outperforms STP with an escape velocity of approximately 10-12 AU/yr. However, future advances in heat exchanger lining materials, turbo pumps, and advanced heat exchanger geometries may enable solar thermal propulsion to provide higher escape velocities, providing one of the fastest ways to exit the solar system. Ultimately, if all technology paths could be implemented with minimal side effects, the performance in a best-case scenario could reach up to 16 AU/yr.

Alkalai, Leon↗
NASA NTRS2018

Bureau of Networks and Observations

Role of the Bureau: To advocate and encourage implementation of the Core and Co-location Network to satisfy GGOS requirements, to monitor the status of the network and project its future condition, and to support and advocate for infrastructure critical for the development of data products essential to GGOS.

Pearlman, Michael R.↗
NASA NTRS2016

Electrospray Thruster Performance with Microfabricated Emitter Arrays and Indium Propellant

The feasibility of a microfabricated indium-fueled electrospray thruster with excellent performance was demonstrated. High efficiency electrospray thrusters with microfabricated components are under development for very compact, distributable propulsion systems that can be employed on both very small and large spacecraft with 10X improvement over SOA in mass, volume and specific impulse The critical components of this technology are the microfabricated emitter arrays and the capillary force driven indium feed system. Grey scale electron-beam lithography patterning and reactive ion dry etching provided the required micron-scale etch precision and uniformity across an array of 400 emitters in 1 cm2. Initial tests of single microfabricated silicon emitters demonstrated better performance than industry standard single emitters and the performance required to achieve 200 micronewtons when scaled up to a thruster with 400 emitters in 1 cm2. Arrays of emitters tested in a preliminary prototype Microfluidic Electrospray Propulsion (MEP) thruster assembly demonstrated stable performance at estimated thrust levels of 5, 50, and 120 µN at extraction voltages less than 4 kV. Current stability was within 0.15 % at 120 µN with only 1.5% of the emitter current collected by the extractor electrode. Post-test inspections revealed that more than 99% of the 400 emitters were electrospraying during the test. Specific impulse was estimated to be >3100 s from measurements of total charge and consumed indium mass at an emitter voltage of 1470 V. The results of this investigation suggest that microfabricated indium electrospray thruster technology is both feasible and capable of excellent performance as a highly compact microthruster.

Marrese-Reading, Colleen M.↗
NASA NTRS2016

Update on the activities of the GGOS Bureau of Networks and Observations

The recently reorganized GGOS Bureau of Networks and Observations has many elements that are associated with building and sustaining the infrastructure that supports the Global Geodetic Observing System (GGOS) through the development and maintenance of the International Terrestrial and Celestial Reference Frames, improved gravity field models and their incorporation into the reference frame, the production of precision orbits for missions of interest to GGOS, and many other applications. The affiliated Service Networks (IVS, ILRS, IGS, IDS, and now the IGFS and the PSMSL) continue to grow geographically and to improve core and co-location site performance with newer technologies. Efforts are underway to expand GGOS participation and outreach. Several groups are undertaking initiatives and seeking partnerships to update existing sites and expand the networks in geographic areas void of coverage. New satellites are being launched by the Space Agencies in disciplines relevant to GGOS. Working groups now constitute an integral part of the Bureau, providing key service to GGOS. Their activities include: projecting future network capability and examining trade-off options for station deployment and technology upgrades, developing metadata collection and online availability strategies; improving coordination and information exchange with the missions for better ground-based network response and space-segment adequacy for the realization of GGOS goals; and standardizing site-tie measurement, archiving, and analysis procedures. This poster will present the progress in the Bureau's activities and its efforts to expand the networks and make them more effective in supporting GGOS.

Networks↗
NASA NTRS2013

Technology Development Roadmap: A Technology Development Roadmap for a Future Gravitational Wave Mission

Humankind will detect the first gravitational wave (GW) signals from the Universe in the current decade using ground-based detectors. But the richest trove of astrophysical information lies at lower frequencies in the spectrum only accessible from space. Signals are expected from merging massive black holes throughout cosmic history, from compact stellar remnants orbiting central galactic engines from thousands of close contact binary systems in the Milky Way, and possibly from exotic sources, some not yet imagined. These signals carry essential information not available from electromagnetic observations, and which can be extracted with extraordinary accuracy. For 20 years, NASA, the European Space Agency (ESA), and an international research community have put considerable effort into developing concepts and technologies for a GW mission. Both the 2000 and 2010 decadal surveys endorsed the science and mission concept of the Laser Interferometer Space Antenna (LISA). A partnership of the two agencies defined and analyzed the concept for a decade. The agencies partnered on LISA Pathfinder (LPF), and ESA-led technology demonstration mission, now preparing for a 2015 launch. Extensive technology development has been carried out on the ground. Currently, the evolved Laser Interferometer Space Antenna (eLISA) concept, a LISA-like concept with only two measurement arms, is competing for ESA's L2 opportunity. NASA's Astrophysics Division seeks to be a junior partner if eLISA is selected. If eLISA is not selected, then a LISA-like mission will be a strong contender in the 2020 decadal survey. This Technology Development Roadmap (TDR) builds on the LISA concept development, the LPF technology development, and the U.S. and European ground-based technology development. The eLISA architecture and the architecture of the Mid-sized Space-based Gravitational-wave Observatory (SGO Mid)-a competitive design with three measurement arms from the recent design study for a NASA-led mission after 2020-both use the same technologies. Further, NASA participation in an ESA-led mission would likely augment the eLISA architecture with a third arm to become the SGO Mid architecture. For these reasons, this TDR for a future GW mission applies to both designs and both programmatic paths forward. It is adaptable to the different timelines and roles for an ESA-led or a NASA-led mission, and it is adaptable to available resources. Based on a mature understanding of the interaction between technology and risk, the authors of this TDR have chosen a set of objectives that are more expansive than is usual. The objectives for this roadmap are: (1) reduce technical and development risks and costs; (2) understand and, where possible, relieve system requirements and consequences; (3) increase technical insight into critical technologies; and (4) validate the design at the subsystem level. The emphasis on these objectives, particularly the latter two, is driven by outstanding programmatic decisions, namely whether a future GW mission is ESA-led or NASA-led, and availability of resources. The relative emphasis is best understood in the context of prioritization.

Laser Interferometry Space Antenna↗
NASA NTRS2010

Survey of Propulsion Technologies Applicable to Cubesats

At present, no Cubesat has flown in space featuring propulsion. This was acceptable as long as CubeSats were flown mostly as university experiments. As CubeSats become of interest to other users in the government and industry communities as well, a larger range of capabilities may be required than exhibited so far, while maintaining the uniqueness of the Cubesat platform. Propulsion capability is crucial in increasing mission capabilities of future CubeSats, such as orbit change and raising, formation flying, proximity operations, fine attitude control, or drag-make-up and de-orbit. While some of these tasks may be accomplished with propellantless devices, their applications are limited, applicable mostly to a single task, and bear their own risks. In this study, a survey was conducted of propulsion technologies applicable to CubeSats. Only few off-the-shelf design solutions exist today. The survey was thus expanded to such devices as well that are under significant development, and are approaching the required design envelope for CubeSats with respect to mass, volume, and power. In some cases, such as electric propulsion devices, CubeSat architectures themselves may need to be adapted, required to feature deployable solar arrays to increase power capabilities. Given the vast scope of this survey, only thruster technologies could be surveyed. However, valves and other feed system components, as well as their integration, are equally important, but have to be left to a future survey. Three major propulsion technology areas applicable to CubeSats emerged when conducting this review: (1) Existing technologies, such as butane systems, pulsed plasma thrusters, and vacuum arc thrusters are applicable to CubeSats today with no or only minor changes, (2) New thruster technologies under significant development, such as hydrazine monopropellant systems, ion engines, or colloid thrusters could be adapted to CubeSats with some further development, especially also in other subsystem areas such as feed systems and power processing units. They will also require increased power capabilities, and (3) emerging technologies, such as micro electrospray arrays and micro cavity discharge arrays that offer even higher flexibility due to scalability for CubeSats, and enable compact integration.

micropropulsion↗
NASA NTRS2010

Mission Enabling and Enhancing Spacecraft Capabilities with MicroNewton Electric Propulsion

The capability to significantly improve current spacecraft pointing, precision orbit maintenance and disturbance mitigation were considered using precision, quiescent microNewton electric propulsion systems. Analysis results showed that electric propulsion systems operating in the microNewton to hundreds of microNewtons thrust range can offer significant improvements over state-of-the-art mission capabilities to enable 30 m Earth-fixed orbital tubes, constellation spacecraft position control to within nanometers and exoplanet observatory pointing with 0.1 milliarcsecond precision. Specific thrust levels and profiles required to support these capabilities are discussed.

micro propulsion↗
NASA NTRS2006

Micro-Inspector Spacecraft: An Overview

JPL has developed a small(<5 kg) spacecraft capable of visual inspection of a host vehicle with support from NASA's Exploration Systems Mission Directorate (ESMD). This paper describes the multi-mission utility of the Micro-Inspector and presents an overview of the spacecraft system and subsystem designs, description of a typical inspection mission scenario, and initial hardware demonstrations of key subsystems, partially integrated with each other in a Micro-Inspector testbed at JPL.

microsatellite inspectors↗
NASA NTRS2005

Photochemically Etched Construction Technology Developed for Digital Xenon Feed Systems

Electric propulsion systems are quickly emerging as attractive options for primary propulsion in low Earth orbit, in geosynchronous orbit, and on interplanetary spacecraft. The driving force behind the acceptance of these systems is the substantial reduction in the propellant mass that can be realized. Unfortunately, system designers are often forced to utilize components designed for chemical propellants in their electric systems. Although functionally acceptable, these relatively large, heavy components are designed for the higher pressures and mass flow rates required by chemical systems. To fully realize the benefits of electric propulsion, researchers must develop components that are optimized for the low flow rates, critical leakage needs, low pressures, and limited budgets of these emerging systems.

Otsap, Ben↗
NASA NTRS2005

Micro-Inspector Spacecraft for Space Exploration Missions

NASA is seeking to embark on a new set of human and robotic exploration missions back to the Moon, to Mars, and destinations beyond. Key strategic technical challenges will need to be addressed to realize this new vision for space exploration, including improvements in safety and reliability to improve robustness of space operations. Under sponsorship by NASA's Exploration Systems Mission, the Jet Propulsion Laboratory (JPL), together with its partners in government (NASA Johnson Space Center) and industry (Boeing, Vacco Industries, Ashwin-Ushas Inc.) is developing an ultra-low mass (<3.0 kg) free-flying micro-inspector spacecraft in an effort to enhance safety and reduce risk in future human and exploration missions. The micro-inspector will provide remote vehicle inspections to ensure safety and reliability, or to provide monitoring of in-space assembly. The micro-inspector spacecraft represents an inherently modular system addition that can improve safety and support multiple host vehicles in multiple applications. On human missions, it may help extend the reach of human explorers, decreasing human EVA time to reduce mission cost and risk. The micro-inspector development is the continuation of an effort begun under NASA's Office of Aerospace Technology Enabling Concepts and Technology (ECT) program. The micro-inspector uses miniaturized celestial sensors; relies on a combination of solar power and batteries (allowing for unlimited operation in the sun and up to 4 hours in the shade); utilizes a low-pressure, low-leakage liquid butane propellant system for added safety; and includes multi-functional structure for high system-level integration and miniaturization. Versions of this system to be designed and developed under the H&RT program will include additional capabilities for on-board, vision-based navigation, spacecraft inspection, and collision avoidance, and will be demonstrated in a ground-based, space-related environment. These features make the micro-inspector design unique in its ability to serve crewed as well as robotic spacecraft, well beyond Earth-orbit and into arenas such as robotic missions, where human teleoperation capability is not locally available.

microspacecraft↗
NASA NTRS1999

The Mars Development of a Micro-Isolation Valve

A feasibility investigation for a newly proposed microfabricated, normally-closed isolation valve was initiated. The micro-isolation valve is silicon based and relies on the principle of melting a silicon plug, opening an otherwise sealed flow passage. This valve may thus serve a similar role as a conventional pyrovalve and is intended for use in micropropulsion systems onboard future microspacecraft, having wet masses of no more than 10-20 kg, as well as in larger scale propulsion systems having only low flow rate requirements, such as ion propulsion or Hall thruster systems. Two key feasibility issues - melting of the plug and pressure handling capability - were addressed. Thermal finite element modeling showed that valves with plugs having widths between 10 and 50 gm have power requirements of only 10 . 30 Watts to open over a duration of 0.5 ms or less. Valve chips featuring 5 0 micron plugs were burst pressure tested and reached maximum pressure values o f 2900 psig (19.7 Mpa).

Mueller, Juergen↗
NASA NTRS1999

MEMS Micropropulsion Activities at JPL

A status of MEMS-based micropropulsion activities conducted at JPL will be given. These activities include work conducted on the so called Vaporizing Liquid Micro-Thruster (VLM) which recently underwent proof-of-concept testing, demonstrating the ability to vaporize water propellant at 2 W and 2 V. Micro-ion engine technologies, such m field emitter arrays and micro-grids are being studied. Focus in the field emitter area is on arrays able to survive in thruster plumes and micro-ion engine plasmas to serve as neutralizers aW engine cathodes. Integrated, batch-fabricated Ion repeller grid structures are being studied as well as different emitter tip materials are being investigated to meet these goals. A micro-isolation valve is being studied to isolate microspacecraft feed system during long interplanetary cruises, avoiding leakage and prolonging lifetime and reliability of such systems. This concept relies on the melting of a thin silicon barrier. Burst pressure values as high as 2,900 psig were obtained for these valves and power requirements to melt barriers ranging between 10 - 50 microns in thickness, as determined through thermal finite element calculations, varied between 10 - 30 W to be applied over a duration of merely 0.5 ms.

Mueller, Juergen↗