Engineering topics

Newman, J. C., Jr.

Publications and source records attributed to Newman, J. C., Jr..

At least 73 records · Page 4

NASA NTRS1991

Parallel computation in a three-dimensional elastic-plastic finite-element analysis

CRAY 2 and CRAY Y-MP evaluation runs are undertaken for a three-dimensional, elastoplastic FEM code implementation of the 'autotasking' parallel-processing technique, which is used in all code components except the matrix-equation solver. For a typical example problem in the case of a four-processor CRAY 2, a speedup factor of 2.1 was found achievable in a dedicated environment, and 1.7 in a multiuser environment; for a three-processor CRAY Y-MP, speedup in a multiuser environment was about 2.4. Only minimal effort was required to implement autotasking in this implementation code.

Shivakumar, K. N.↗

NASA NTRS1990

ZIP3D: An elastic and elastic-plastic finite-element analysis program for cracked bodies

ZIP3D is an elastic and an elastic-plastic finite element program to analyze cracks in three dimensional solids. The program may also be used to analyze uncracked bodies or multi-body problems involving contacting surfaces. For crack problems, the program has several unique features including the calculation of mixed-mode strain energy release rates using the three dimensional virtual crack closure technique, the calculation of the J integral using the equivalent domain integral method, the capability to extend the crack front under monotonic or cyclic loading, and the capability to close or open the crack surfaces during cyclic loading. The theories behind the various aspects of the program are explained briefly. Line-by-line data preparation is presented. Input data and results for an elastic analysis of a surface crack in a plate and for an elastic-plastic analysis of a single-edge-crack-tension specimen are also presented.

Shivakumar, K. N.↗

NASA NTRS1990

An evaluation of the pressure proof test concept for thin sheet 2024-T3

The concept of pressure proof testing of fuselage structures with fatigue cracks to insure structural integrity was evaluated from a fracture mechanics viewpoint. A generic analytical and experimental investigation was conducted on uniaxially loaded flat panels with crack configurations and stress levels typical of longitudinal lap-splice joints in commercial transport aircraft fuselage. The results revealed that the remaining fatigue life after a proof test was longer than that without the proof test because of crack growth retardation due to increased crack closure. However, based on a crack length that is slightly less than the critical value at the maximum proof test stress, the minimum assured life or proof test interval must be no more than 550 pressure cycles for a 1.33 proof factor and 1530 pressure cycles for a 1.5 proof factor to prevent in-flight failures.

Dawicke, D. S.↗

NASA NTRS1990

Fatigue crack initiation and small crack growth in several airframe alloys

The growth of naturally-initiated small cracks under a variety of constant amplitude and variable amplitude load sequences is examined for several airframe materials: the conventional aluminum alloys, 2024-T3 and 7075-T6, the aluminum-lithium alloy, 2090-T8E41, and 4340 steel. Loading conditions investigated include constant amplitude loading at R = 0.5, 0, -1 and -2 and the variable amplitude sequences FALSTAFF, Mini-TWIST and FELIX/28. Crack growth was measured at the root of semicircular edge notches using acetate replicas. Crack growth rates are compared on a stress intensity factor basis, to those for large cracks to evaluate the extent of the small crack effect in each alloy. In addition, the various alloys are compared on a crack initiation and crack growth morphology basis.

Swain, M. H.↗

NASA NTRS1990

Through-the-thickness fatigue crack closure behavior in an aluminum alloy

The variation in fatigue crack closure behavior across the thickness of aluminum alloy specimens was investigated. The specimen geometries examined were the middle crack tension M(T) and compact tension C(T). The fatigue crack closure behavior was determined using remote displacement and strain gages, near tip strain gages, and fatigue striations. A hybrid experimental/numerical method was also used to infer the crack opening loads. The results indicate a variation in crack opening load, of 0.2 in the specimen interior to 0.4 to 0.5 at the surface.

Dawicke, D. S.↗

NASA NTRS1990

Three-dimensional crack closure behavior

A crack closure measurement technique involving fatigue striations was used to produce a three-dimensional crack opening load profile for 2024-T351 aluminum alloy. The crack opening load profile, determined through the specimen thickness, was compared with crack opening load measurements made with strain gages and displacement gages. The results of this study indicate that a significant three-dimensional variation in crack closure behavior occurs in the alloy examined. An understanding of this phehomenon is important in understanding crack growth behavior, predicting crack shape changes, and interpreting 'standard' crack closure measurement techniques.

Dawicke, D. S.↗

NASA NTRS1990

Evaluation of finite-element models and stress-intensity factors for surface cracks emanating from stress concentrations

A re-evaluation of the 3-D finite-element models and methods used to analyze surface crack at stress concentrations is presented. Previous finite-element models used by Raju and Newman for surface and corner cracks at holes were shown to have ill-shaped elements at the intersection of the hole and crack boundaries. Improved models, without these ill-shaped elements, were developed for a surface crack at a circular hole and at a semi-circular edge notch. Stress-intensity factors were calculated by both the nodal-force and virtual-crack-closure methods. Comparisons made between the previously developed stress-intensity factor equations and the results from the improved models agreed well except for configurations with large notch-radii-to-plate-thickness ratios. Stress-intensity factors for a semi-elliptical surface crack located at the center of a semi-circular edge notch in a plate subjected to remote tensile loadings were calculated using the improved models.

Tan, P. W.↗

NASA NTRS1990

Fatigue crack propagation in aerospace aluminum alloys

This paper reviews fracture mechanics based, damage tolerant characterizations and predictions of fatigue crack growth in aerospace aluminum alloys. The results of laboratory experimentation and modeling are summarized in the areas of: (1) fatigue crack closure, (2) the wide range crack growth rate response of conventional aluminum alloys, (3) the fatigue behavior of advanced monolithic aluminum alloys and metal matrix composites, (4) the short crack problem, (5) environmental fatigue, and (6) variable amplitude loading. Remaining uncertainties and necessary research are identified. This work provides a foundation for the development of fatigue resistant alloys and composites, next generation life prediction codes for new structural designs and extreme environments, and to counter the problem of aging components.

Gangloff, R. P.↗

NASA NTRS1990

Fatigue crack initiation and small crack growth in several airframe alloys

The growth of naturally-initiated small cracks under a variety of constant amplitude and variable amplitude load sequences is examined for several airframe materials: the conventional aluminum alloys, 2024-T3 and 7075-T6, the aluminum-lithium alloy, 2090-T8E41 and 4340 steel. Loading conditions investigated include constant amplitude loading at R = 0.5, 0, -1 and -2 and the variable amplitude sequences FALSTAFF, Mini-TWIST, and FELIX/28. Crack growth was measured at the root of semicircular edge notches using acetate replicas. Crack growth rates are compared on a stress intensity factor basis, to those for large cracks to evaluate the extent of the small crack effect in each alloy. In addition, the various alloys are compared on a crack initiation and crack growth morphology basis.

Swain, M. H.↗

NASA NTRS1990

Through-the-thickness fatigue crack closure behavior in an aluminum alloy

Dawicke, D. S.↗

NASA NTRS1990

Proof test and fatigue crack growth modeling on 2024-T3 aluminum alloy

Pressure proof testing of aircraft fuselage structures has been suggested as a means of screening critical crack sizes and of extending their useful life. The objective of this paper is to study the proof-test concept and to model the crack-growth process on a ductile material. Simulated proof and operational fatigue life tests have been conducted on cracked panels made of 2024-T3 aluminum alloy sheet material. A fatigue crack-closure model was modified to simulate the proof test and operational fatigue cycling. Using crack-growth rate and resistance-curve data, the model was able to predict crack growth during and after the proof load. These tests and analyses indicate that the proof test increases fatigue life; but the beneficial life, after a 1.33 or 1.5 proof, was less than a few hundred cycles.

Newman, J. C., Jr.↗

NASA NTRS1989

Impact of small-crack effects on design-life calculations

The potential impact of the observed small-crack-effect in 2024-T3 aluminum alloy on calculated crack-growth lives is described. The significance of the small-crack effect is assessed by comparing lives computed using only large-crack data to those computed using a combined small- and large-crack data base for constant-amplitude (R = -1 and 0) and fighter-wing spectrum loading (FALSTAFF) conditions. Based on the life calculations, the small-crack effect would have no impact on life analyses that assume an initial crack larger than about 0.3 mm; only a small impact on life analyses that assume an initial crack of 0.1 mm; but a large impact on life analyses that assume an initial crack of about 0.01 mm. When small-crack effects are taken into account, fatigue life analyses based solely on crack growth may provide a viable alternative to traditional two-part initiation-plus-crack-growth life analyses.

Phillips, E. P.↗

NASA NTRS1989

Prediction of fatigue-crack growth in a high-strength aluminum alloy under variable-amplitude loading

The present paper is concerned with the application of an analytical crack-closure model to study crack growth under various load histories. The model was based on a concept like the Dugdale model, but modified to leave plastically deformed material in the wake of the advancing crack tip. The thickness effect was accounted for by using a 'constraint' factor on tensile yielding at the crack tip. The model was used to correlate crack-growth rates under constant-amplitude loading, and to predict crack growth under variable-amplitude loading on a high-strength aluminum alloy (7475-T7351) sheet material. The experimental data was obtained from Zhang et al. Predicted crack-growth lives agreed well with experimental data. For ten crack-growth tests subjected to various variable-amplitude load histories, the ratio of predicted-to-experimental lives ranged from 0.54 to 1.19. The mean value of predicted-to-experimental lives was 0.95 with a standard error of 0.2 for a constraint factor of 1.9.

Newman, J. C., Jr.↗

NASA NTRS1989

Prediction of fatigue-crack growth in a high-strength aluminum alloy under variable-amplitude loading

The present paper is concerned with the application of an analytical crack-closure model to study crack growth under various load histories. The model was based on a crack-tip plasticity concept like the Dugdale model, but modified to leave plastically deformed material in the wake of the advancing crack tip. The effect of material thickness on plasticity was accounted for by using a constraint factor on tensile yielding at the crack tip. The model was used to correlate crack-growth rates under constant-amplitude loading, and to predict crack growth under variable-amplitude loading on a high-strength aluminum alloy (7475-T7351) sheet material. The experimental data were obtained from Zhang et al. Predicted crack-growth lives agreed well with experimental data. For ten crack-growth tests subjected to various variable-amplitude load histories, the ratio of predicted-to-experimental lives ranged from 0.54 to 1.19. The mean value of the ratio of predicted-to-experimental lives was 0.95 and the standard error was 0.2 using a constraint factor of 1.9 in the model. Crack-opening stresses calculated from the model were significantly different from those determined by Zhang et al. using a striation-based experimental method.

Newman, J. C., Jr.↗

NASA NTRS1989

Numerical fracture simulation of bend specimens using a CTOD criterion

Stable crack growth in 50-mm-thick side-grooved three-point bend specimens of HY-130 steel is modeled numerically. A two-dimensional elastoplastic FEM formulation incorporating a CTOD fracture criterion is developed analytically, and the theoretical predictions are compared with experimental data in graphs. Good general agreement is obtained, except for the crack extension, which was typically overpredicted. The value of the J integral at crack initiation is found to be 83 kJ/sq m.

Shivakumar, K. N.↗

NASA NTRS1989

Three-dimensional aspects of plasticity-induced fatigue crack closure

A three-dimensional elastoplastic finite element analysis of fatigue crack growth and closure in a center-crack tension specimen was performed in order to investigate the crack opening stress as a function of specimen thickness under constant amplitude loading conditions. Elastic-perfectly plastic conditions were assumed and cycle loading was kept at R = 0.1. Firstly, by imposing proper boundary conditions on the three-dimensional model, a plane strain analysis was carried out. The ratio of stabilized opening stress over the maximum applied stress under plane strain conditions was found to be 0.28. Secondly, the model thickness was varied under fully three-dimensional conditions, and crack-opening stresses were determined for each specimen thickness. The crack-opening stress is found to vary through the thickness for the center crack tension specimen. On the specimen surface and in the midplane the crack-opening stress levels tend to two-dimensional solutions for plane stress and plane strain conditions, respectively.

Chermahini, R. G.↗

NASA NTRS1988

Short-crack growth behaviour in an aluminum alloy: An AGARD cooperative test program

An AGARD Cooperative Test Program on the growth of short fatigue cracks was conducted to define the significance of the short-crack effect, to compare test results from various laboratories, and to evaluate an existing analytical crack-growth prediction model. The initiation and growth of short fatigue cracks (5 micrometer to 2 mm) from the surface of a semi-circular notch in 2024-T3 aluminum alloy sheet material were monitored under various load histories. The cracks initiated from inclusion particle clusters or voids on the notch surface and generally grew as surface cracks. Tests were conducted under several constant-amplitude (stress ratios of -2, -1, 0, and 0.5) and spectrum (FALSTAFF and Gaussian) loading conditions at 3 stress levels each. Short crack growth was recorded using a plastic-replica technique. Over 250 edge-notched specimens were fatigue tested and nearly 950 cracks monitored by 12 participants from 9 countries. Long crack-growth rate data for cracks greater than 2 mm in length were obtained over a wide range in rates (10 to the -8 to 10 to the -1 mm/cycle) for all constant-amplitude loading conditions. Long crack-growth rate data for the FALSTAFF and Gaussian load sequences were also obtained.

Newman, J. C., Jr.↗

NASA NTRS1988

Preliminary fatigue tests on short-crack specimens

The objective of the preliminary fatigue tests was to determine the stress levels to be used by the participants in the Cooperative Test Program. As previously mentioned, the United States Air Force Wright-Patterson Aeronautical Laboratory machined about 700 single-edge-notched tension (SENT) specimens from material supplied by the NASA Langley Research Center. In addition, NASA Langley machined about 50 SENT specimens from the same material. Comparison of fatigue tests conducted on the two sets of specimens indicated a large difference in fatigue behavior under constant-amplitude loading. A recovery program was initiated to resolve this difference before the specimens were distributed to participants. The following sections describe the recovery program and the preliminary fatigue tests and analyses conducted to determine stress levels for constant-amplitude, FALSTAFF, and Gaussian loading.

Newman, J. C., Jr.↗