Engineering topics

Perkins, Craig

Publications and source records attributed to Perkins, Craig.

6 records

DOE OSTI2023

Collaborative R&D with First Solar on Understanding Performance Limitations in CdTe (Project 1 "CdTe" - Mods 0-10, 13, 14-A1, 17)

This CRADA involves analyses on a variety of CdTe and CdTe-PV related materials, test structures, and solar cells produced at FSLR or NREL. Single-crystal (sx) material will be primarily MBE grown and provided by FSLR. Joint activities are focused on establishing the appropriate quality metrics as a basis for high performing sx devices and to study the dopability of the material. Polycrystalline (px) materials will be provided by NREL, FSLR, or fabricated jointly. Px activities are focused on the characterization of performance limiting mechanisms including bulk defects, grain boundaries, and the hetero-interface. A combination of growth, characterization, and theory will be applied. Analysis will include techniques that are well established in CdTe research at NREL (e.g., LIV/DIV/CV, AS/DLTS, LTPL, TRPL) as well as techniques that have not been widely applied to the PV part of CdTe technology (e.g., PCD, CL, uPL, SE).

14 SOLAR ENERGY↗

DOE OSTI2022

Evaluation of PbTe and SnTe as Ohmic Contact Layers in CdTe Solar Cell Devices

For solar cells based on CdTe, the choice of a suitable back contact material is limited by CdTe's deep work function. Here, we explored p-type PbTe and SnTe as ohmic contacts to CdTe. These contact layers were grown on single crystal CdTe substrates by molecular beam epitaxy, and the valence band offset between film and substrate was measured using X-ray photoemission spectroscopy. Polycrystalline device structures were also grown by sublimation to assess performance improvements. Doping was achieved in PbTe by thallium incorporation. Only the highest Tl doped PbTe resulted in a desirable band alignment with the CdTe, forming an electron reflector and no hole barrier. Time-resolved photoluminescence measurements also revealed significant photocarrier lifetime improvements for only the highest doped PbTe. Consequentially, devices incorporating the highest doped PbTe layers showed increased power conversion efficiency, primarily from increased fill factor. Doping of the PbTe was measured via Hall effect with variable magnetic field, which was required due to the formation of an n-type parasitic interface layer. To properly interpret the variable field Hall measurements, we derived an expression for the magnetic field-dependent conductivity tensor of an L-valley semiconductor.

anisotropic band valley↗

DOE OSTI2021

High Efficiency Evaporated CdSeTe/CdTe Solar Cells With and Without MgZnO Buffer Layer

High efficiencies of ~19% CdTe solar cell devices were made using a thermal evaporation technique to deposit absorber layers of CdSe and CdTe. The absorber films were very high quality for a device fabrication, and with demonstrated high efficiency, it is a viable option to employ thermal evaporation in research and manufacturing. We also investigated four different interfaces scenarios of with and without MZO and CdSe in the device near front interface. The results clearly indicate that Se plays a key role in improving device performance, but the MZO is not necessarily required unless experiment goals demanded. Removing the MZO layer from the device structure and being able to use thermal evaporator for CdTe deposition will help with cost reduction in manufacturing.

41 EE - Solar Energy Technologies Office (EE-4S)↗

DOE OSTI2020

High-Temperature Nucleation of GaP on V-Grooved Si

The use of nanopatterned {111}-faceted v-grooves has recently shown promise for growing high-quality III–V material on Si. Here, we study the effect of reactor conditions and surface pretreatments on the nucleation of GaP on v-grooved Si in a high-temperature regime, which offers the promise of a defect-free GaP/Si interface favorable for Si passivation and dislocation glide in the GaP. X-ray photoelectron spectroscopy was used to understand the Si surface chemistry prior to nucleation, and transmission electron microscopy was used to probe material quality of the nuclei. Temperature and V/III ratio were found to control the facet selectivity of nucleation. We demonstrate a condition of high temperature and high V–III ratio that leads to uniform nucleation at the bottom of the trenches, with initial material free of nucleation-related interfacial defects. This optimized condition was then shown to coalesce into a thin film after additional growth.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Thin-Film Solar Cells with 19% Efficiency by Thermal Evaporation of CdSe and CdTe

CdTe-based solar cells exhibiting 19% power conversion efficiency were produced using widely available thermal evaporation deposition of the absorber layers on SnO2-coated glass with or without a transparent MgZnO buffer layer. Evaporating CdSe and CdTe sequentially by thermal evaporation and subsequent CdCl2 annealing establishes efffective CdSeTe band grading as well as dense, large-grain films. These results show that high-performance II-VI photovoltaics can be made by inexpensive, commercially available evaporation systems without the need to build customized equipment, enabling CdTe photovoltaics research and manufacturing to be more accessible to the broader photovoltaics community.

14 SOLAR ENERGY↗

DOE OSTI2020

Oxidative Segregation of Group V Dopants in CdTe Solar Cells

Transparent conductive oxides are used in many technologies and it is important to understand their interfacial chemical reactions. Here, we use recently developed thermomechanical cleaving and X-ray photoelectron spectroscopy to probe oxidation states at the SnO 2 interface of CdTe solar cells. We show that tin oxide promotes the formation of nanometer-scale oxides of tellurium and sulfur, largely during CdCl 2 /O 2 activation. Surprisingly, in copper-doped devices, relatively low temperature anneals (180-260 degrees C) to diffuse and activate copper acceptors also cause significant oxidation changes at the front interface, providing a heretofore missing aspect of how back contact processes can modify device transport, recombination, and performance. For Group V-doped devices, this same oxidation process causes segregation of the dopants to the SnO 2 interface in their oxidized states, implying that adjacent regions in the absorber have been depleted of dopants. Intriguingly, we demonstrate that because of their layered, van der Walls-bonded crystal structure, spatially segregated Group V oxides may represent a mechanically weak layer in a finished device.

14 SOLAR ENERGY↗