Search NASA⌕ Search

Engineering topics

Perkins, Craig L.

Publications and source records attributed to Perkins, Craig L..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

GdWN 3 is a nitride perovskite

Nitride perovskites ABN3 are an emerging and highly underexplored class of materials that are of interest due to their intriguing calculated ferroelectric, optoelectronic, and other functional properties. Incorporating novel A-site cations is one strategy to tune and expand such properties; for example, Gd 3+ is compelling due to its large magnetic moment, potentially leading to multiferroic behavior. However, the theoretically predicted ground state of GdWN 3 was a non-perovskite monoclinic structure. Here, we experimentally show that GdWN 3-y crystallizes in a perovskite structure. High-throughput combinatorial sputtering with activated nitrogen is employed to synthesize thin films of Gd 2-x W x N 3-y O y with oxygen content y < 0.05. Ex situ annealing crystallizes a polycrystalline perovskite phase in a narrow composition window near x = 1. LeBail fits of synchrotron grazing incidence wide angle x-ray scattering data are consistent with a perovskite ground-state structure. Refined density functional theory calculations that included antiferromagnetic configurations confirm that the ground-state structure of GdWN 3 is a distorted Pnma perovskite with antiferromagnetic ordering, in contrast to prior predictions. Initial property measurements find that GdWN 3-y is paramagnetic down to T = 2 K with antiferromagnetic correlations and that the absorption onset depends on cation stoichiometry. This work provides an important path toward both the rapid expansion of the emerging family of nitride perovskites and understanding their potential multiferroic properties.

14 SOLAR ENERGY↗
DOE OSTI2024

Multivariate Bayesian Optimization of CoO Nanoparticles for CO 2 Hydrogenation Catalysis

The hydrogenation of CO 2 holds promise for transforming the production of renewable fuels and chemicals. However, the challenge lies in developing robust and selective catalysts for this process. Transition metal oxide catalysts, particularly cobalt oxide, have shown potential for CO 2 hydrogenation, with performance heavily reliant on crystal phase and morphology. Achieving precise control over these catalyst attributes through colloidal nanoparticle synthesis could pave the way for catalyst and process advancement. Yet, navigating the complexities of colloidal nanoparticle syntheses, governed by numerous input variables, poses a significant challenge in systematically controlling resultant catalyst features. We present a multivariate Bayesian optimization, coupled with a data-driven classifier, to map the synthetic design space for colloidal CoO nanoparticles and simultaneously optimize them for multiple catalytically relevant features within a target crystalline phase. The optimized experimental conditions yielded small, phase-pure rock salt CoO nanoparticles of uniform size and shape. These optimized nanoparticles were then supported on SiO 2 and assessed for thermocatalytic CO 2 hydrogenation against larger, polydisperse CoO nanoparticles on SiO 2 and a conventionally prepared catalyst. The optimized CoO/SiO 2 catalyst consistently exhibited higher activity and CH 4 selectivity (ca. 98%) across various pretreatment reduction temperatures as compared to the other catalysts. This remarkable performance was attributed to particle stability and consistent H* surface coverage, even after undergoing the highest temperature reduction, achieving a more stable catalytic species that resists sintering and carbon occlusion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Sn-assisted heteroepitaxy improves ZnTiN 2 photoabsorbers

Ambient temperature growth on Si produces a polycrystalline ZnTiN 2 film while Sn-assisted growth on sapphire at elevated temperature results in a single-crystal-like ZnTiN 2 film with significantly reduced sub-bandgap absorption.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Improving the barrier properties of tin oxide in metal halide perovskite solar cells using ozone to enhance nucleation

Here we investigate tin oxide growth on fullerene (C 60 ) by atomic layer deposition (ALD) for C 60 /oxide bilayer electron selective contacts in P-I-N metal halide perovskite (MHP) solar cells. An in situ ozone functionalization step is incorporated in an ALD SnO x process to suppress sub-surface growth, leading to improved internal barrier performance of ALD SnO x thin films grown on fullerene surfaces. We show that this approach decreases the water-vapor transmission rate of C 60 /ALD SnO x barriers by an order of magnitude and improves the barrier properties against gas, solvent, and halide migration. Furthermore, ozone-treated SnO x barriers can narrow photovoltaic performance distribution without compromising efficiency. We demonstrate the universality of this approach in wide-, intermediate-, and low-gap perovskite systems and further show that enhancement of the ALD barrier layer is critical toward improving the yield of all-perovskite tandem solar cells. Two-terminal all-perovskite tandem solar cells incorporating ozone nucleation are reported at over 24% photovoltaic conversion efficiency.

14 SOLAR ENERGY↗
DOE OSTI2023

Thermomechanical Cleave of Polycrystalline CdTe Solar Cells and its Applications: A Review

One of the primary research challenges for cadmium telluride (CdTe) solar cells is addressing its open‐circuit voltage ( V OC ) deficit. While theoretical studies and single crystal work show V OC > 1 V is possible, devices remain stubbornly low at ≈800–900 mV. As absorber opto‐electronic properties (e.g., hole density, carrier lifetime) are improved, device modeling suggests that interfaces become limiting. Because CdTe‐based devices are typically grown in the superstrate configuration, the back interface is relatively accessible for manipulation and study, while the front interface (i.e., the heterojunction region) is buried under microns of material and inaccessible. NREL has developed a novel technique to thermomechanically cleave polycrystalline CdTe device stacks directly at the front interface, enabling characterization and controlled manipulation of this important region. Herein, recent work, primarily from NREL, will be reviewed, including considerations for achieving successful delamination; key scientific discoveries about the front interface that have been enabled by this technique; and practical applications, such as flexible, low‐cost solar with high power‐to‐weight ratio.

14 SOLAR ENERGY↗
DOE OSTI2023

High Performing Inverted Flexible Perovskite Solar Cells via Solution Phase Deposition of Yttrium-Doped SnO 2 Directly on Perovskite

Solution processing of flexible perovskite solar cells (f-PSCs) provides an avenue for scalable, high-throughput printing of lightweight, scalable, and cost-effective flexible solar cells. However, the deposition of fully solution-processed metal oxide charge transport layers on perovskites has been limited by solvent incompatibilities and high processing temperatures for metal oxide nanoparticles. In this study, we present high-performance, inverted f-PSCs from the direct deposition of yttrium doped SnO 2 nanoparticles functionalized with acetate on top of perovskite as an ink in anhydrous ethanol via blade coating. Yttrium doping improved device performance by improving the charge extraction leading with a decreased series resistance leading to improvements in the open-circuit voltage and fill factor. Furthermore, the champion power conversion efficiency for 0.1 cm 2 devices increased from 14.3% for undoped SnO 2 to 18.2% with 2% Y:SnO 2 doping, which is unprecedented for f-PSCs on ITO-PET substrate employing SnO 2 as an ETL.

14 SOLAR ENERGY↗
DOE OSTI2023

Band Bending at CdTe Solar Cell Contacts: Correlating Electro‐Optical and X‐Ray Photoelectron Spectroscopy Analyses of Thin Film Solar Cells

With the semiconductor bulk properties reaching target values for highly efficient solar cells, efforts are applied to reduce losses at solar cell interfaces and contacts. Advances in understanding back contacts in thin‐film polycrystalline CdTe solar cells, a leading thin‐film PV technology, are reported. By using X‐Ray photoelectron spectroscopy, Kelvin probe spectroscopy, time‐ and energy‐resolved photoluminescence, defects at the back contact are analyzed. Densities of recombination centers and charged defects that induce near‐back‐contact band bending, both resulting in recombination losses, were estimated. Electro‐optical and surface analysis results are integrated into a device model, simulating the performance of CdSeTe/CdTe solar cells with 902 mV open circuit voltage.

14 SOLAR ENERGY↗
DOE OSTI2022

Codesigning Alloy Compositions of CdSe y Te 1− y Absorbers and Mg x Zn 1− x O Contacts to Increase Solar Cell Efficiency

Thin‐film solar cells such as CdTe are a major commercial photovoltaic technology, with more than 25 GW installed worldwide and levelized costs of electricity competitive with fossil fuels. Further progress may result from integrating CdSe y Te 1− y absorbers with Mg x Zn 1− x O contacts, but the device efficiency is difficult to maximize due to coupled dependence on chemical composition of both alloys. Herein, a high‐throughput approach is demonstrated to codesign chemical compositions in alloyed Mg x Zn 1− x O/CdSe y Te 1− y thin‐film solar cells, using combinatorial libraries of PV devices with orthogonal composition gradients in CdSe y Te 1− y absorbers and Mg x Zn 1− x O contacts. It is found that the solar cell performance is a strong and coupled function of both elemental compositions, with efficiency up to 17.7% ( V OC = 836 mV, fill factor = 69%, J SC = 30.6 mA cm −2 ) at atomic compositions of Mg/(Mg + Zn) ≈18% and average Se/(Se + Te) ≈4%. These performance trends among >100 devices are explained by >100 ns lifetime of photoexcited charge carriers at the Mg x Zn 1− x O/CdSe y Te 1− y interface where strong Se accumulation is also observed. This study reports the optimal compositions of the commercially relevant Mg x Zn 1− x O/CdSe y Te 1− y solar cells and demonstrates a general approach to codesigning performance of alloyed thin‐film solar cells and other optoelectronic devices.

14 SOLAR ENERGY↗
DOE OSTI2022

Large-Area (Ag,Cu)(In,Ga)Se 2 Thin-Film Solar Cells with Increased Bandgap and Reduced Voltage Losses Realized with Bulk Defect Reduction and Front-Grading of the Absorber Bandgap

The 1.24 eV bandgap, 18.8% power conversion efficiency Ag-alloyed chalcopyrite (Ag,Cu)(In,Ga)Se 2 (ACIGS) solar cells are characterized to relate voltage and efficiency improvements to electro-optical (EO) characteristics. Shockley-Read-Hall recombination center defect density, identified and characterized through deep level transient spectroscopy and time-resolved photoluminescence (TRPL), is reduced through potassium and copper treatment optimization. Concomitantly, longer minority carrier lifetimes are achieved, which increases open-circuit voltage (V OC ). Near-conduction band defects associated in earlier studies with light-induced current instability are also mitigated. Analysis of charge-carrier dynamics after single- and two-photon excitation is used to separate recombination at the front interface and in the absorber bulk. From TRPL decay simulations, the authors estimate ranges of key solar cell material characteristics: bulk carrier lifetime T bulk = 110-210 ns, charge-carrier mobility u = 110-160 cm 2 V -1 s -1 , and front interface recombination velocity S front = 700-1050 cm s -1 . This lowest-reported S front for ACIGS absorbers originates from the notched conduction band grading, which also makes the impact of the back interface recombination negligible. It is suggested in the results that solar cell performance enhancements can be made most readily with two distinct strategies: improving device architecture and reducing semiconductor defect densities. Using these approaches, power conversion efficiency in large-area solar cells is improved by 1.1% absolute.

14 SOLAR ENERGY↗
DOE OSTI2022

Boron Phosphide Films by Reactive Sputtering: Searching for a P‐Type Transparent Conductor

Abstract With an indirect band gap in the visible and a direct band gap at a much higher energy, boron phosphide (BP) holds promise as an unconventional p‐type transparent conductor. This work reports on reactive sputtering of amorphous BP films, their partial crystallization in a P‐containing annealing atmosphere, and extrinsic doping by C and Si. The highest hole concentration to date for p‐type BP (5 × 10 20 cm −3 ) is achieved using C doping under B‐rich conditions. Furthermore, bipolar doping is confirmed to be feasible in BP. An anneal temperature of at least 1000 °C is necessary for crystallization and dopant activation. Hole mobilities are low and indirect optical transitions are stronger than that predicted by theory. Low crystalline quality probably plays a role in both cases. High figures of merit for transparent conductors might be achievable in extrinsically doped BP films with improved crystalline quality.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Synthesis of LaWN 3 nitride perovskite with polar symmetry

Perovskite structured materials have a variety of uses as photovoltaics, capacitors, and micromechanical actuators, along with other applications. Oxides, halides, and chalcogenides all have large numbers of perovskite structured materials. Examples of perovskite nitrides are conspicuously absent, but Talley et al managed to synthesize one (see the Perspective by Hong). Lanthanum tungsten nitride in the perovskite structure turns out to be piezoelectric, which is ideal for a variety of applications. Perovskite structured nitrides are very attractive because they could easily integrate with the large number of nitride-based semiconducting devices already in use.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Exceeding 200 ns Lifetimes in Polycrystalline CdTe Solar Cells

CdTe photovoltaics has achieved one of the lowest levelized costs of electricity among all energy sources. However, for decades, carrier lifetimes have been inferior to those of other prevalent solar cell materials. This quality has inhibited common methods to improve solar cell efficiency such as back-surface fields, electron reflectors, or bifacial solar cells. In this work, a significant increase in carrier lifetime to values exceeding 200 ns in fully functional CdTe solar cells is demonstrated. The increased lifetime is achieved by large CdSeTe grains at the absorber/emitter interface, intragrain passivation in the absorber layer, and chemical passivation by forming nanoscale oxidized tellurium species at the transparent conducting oxide interface. The carrier lifetime is correlated to the open-circuit voltage and enables paths for back-surface manipulation and novel cell architectures to further improve CdTe photovoltaic performance.

14 SOLAR ENERGY↗
DOE OSTI2021

Mechanisms for long carrier lifetime in Cd(Se)Te double heterostructures

II–VI semiconductors are used in numerous electro-optical applications. For example, CdTe-based solar technology is cost competitive with other electricity generation sources, yet there is still significant room to improve. Carrier lifetime has historically been well below the radiative recombination limit. Lifetimes reaching beyond 100 ns can significantly enhance performance and enable novel device structures. Here, double heterostructures (DHs) with passivated interfaces demonstrate lifetimes exceeding 1 µs, yet this appears only for CdSeTe and not for CdTe DHs. We compare the passivation mechanisms in CdTe and CdSeTe DHs. CdSeTe lifetimes on the order of 1 µs correspond to a combination of superior intragrain lifetime, extremely low grain boundary recombination and greater Te4+ interfacial presence compared to CdTe.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Influence of Protection Layers on Thermal Stability of Nitride Thin Films

Nitrides are commonly studied for their properties relevant to numerous coating applications, and have been recently used to synthesize newly predicted materials in thin film form. However, thermodynamic stability of such nitride materials is difficult to experimentally evaluate, due to limited thermal budget of thin films. Here we show that thermal stability of nitride films can be extended using protection layers. Specifically, we find that zirconium nitride (ZrN) thin films are stable up to at least 1200°C annealing temperature in N2 atmosphere, if aluminum nitride (AlN) diffusion barriers and capping layers are used. X-ray diffraction (XRD) measurements show the expected thermodynamically stable rocksalt structure of ZrN, and scanning electron microscopy (SEM) confirms compact microstructure of these ZrN films. Without such protection layers, transient bixbyite Zr2ON2 phase and high-temperature ZrSi2 phase are observed after annealing by XRD, SEM, and auger electron spectroscopy (AES), due to side reaction with native surface oxide (ZrOx) and substrate (Si) respectively. These results demonstrate that protection layers are beneficial to increase the thermal budget of nitride thin films, for evaluating thermodynamic stability of new nitride materials, for capturing transient metastable phases during crystallization, and for using functional nitride coatings in extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ Al 2 O 3 incorporation enhances the efficiency of CuIn(S,Se) 2 solar cells prepared from molecular-ink solutions

Here, we report an efficiency enhancement of solution-processed CuIn(S,Se) 2 (CISSe) thin film solar cells via in situ incorporation of Al 2 O 3 . These films were produced using inks containing CuCl, InCl 3 , AlNO 3 (Al/Al + In: 0.1) and thiourea dissolved in methanol. After spin coating of these solutions in air, samples were subjected to a selenization process. Auger electron spectroscopy depth-profiling analysis showed that Al is evenly distributed throughout the bulk of the film. Transmission electron microscopy revealed that AlNO 3 precursor reacted with oxygen to form nanosized amorphous Al 2 O 3 grains located within the bulk and grain boundaries of CISSe, as well as at both the top and bottom interfaces. Power conversion efficiency (PCE) as high as 11.6% (JS C : 35.8 mA cm –2 , V OC : 518 mV, FF: 62.2%, no anti-reflection coating) was achieved with Al–CISSe solar cell devices integrated with CdS (chemical bath deposition, thickness: 80 nm) and ZnO/ITO bilayers (sputtered, thickness: 300 nm). The average PCE (10.1%, $\langle$J SC $\rangle$: 34.5 mA cm –2 , $\langle$V OC $\rangle$: 491 mV, $\langle$FF$\rangle$: 59.8%) was nearly 4% (absolute) higher than that measured on CISSe baseline cells fabricated from solutions without Al ($\langle$PCE$\rangle$ = 6.4%, $\langle$J SC $\rangle$: 32.8 mA cm –2 , $\langle$V OC $\rangle$: 410 mV, $\langle$FF$\rangle$: 47.3%). This in situ Al 2 O 3 incorporation is speculated to play a role in the enhancement of the VOC and FF of the devices through passivation of defects in CISSe reducing interface and bulk recombination, as evidenced by a reduced defect density and an increased activation energy of the dominant recombination mechanism from capacitance and temperature-dependent VOC measurements, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗