Engineering topics

Plotkowski, Alex

Publications and source records attributed to Plotkowski, Alex.

At least 19 records

DOE OSTI2024

A dynamic volumetric heat source model for laser additive manufacturing

Melt pool scale models of laser powder bed fusion (LPBF) offer insights into the process-structure-property relationships in additive manufacturing (AM). These models often neglect physical phenomena such as vapor cavity formation and fluid mechanics to reduce computational demands. Instead, volumetric heat source models are used to represent the effects that these phenomena have on the predicted melt pool dimensions. Generally, the dimensions and effective absorption of the volumetric heat source are calibrated to reproduce melt pool dimensions observed in metallographic cross sections taken from single-track experiments on bare plate. However, the transient nature of LPBF often deviates the melt pool dimensions from the assumed steady-state conditions of single-track experiments, motivating the need for a volumetric heat source model that more generally considers the dynamic relationship between melt pool shape and laser-material interactions. Here, we introduce a two-parameter volumetric heat source model that integrates several existing models into a generalized mathematical expression, providing independent control over the radial heat distribution via the parameter k and the volumetric shape of the heat source via the parameter m. This parameterization enables the calibration of melt pool shape predictions through simultaneous adjustment of these parameters, while keeping the radial heat source dimensions consistent with the experimental spot size (D4σ) and constraining the heat source depth and absorption to physically derived expressions for cavities. Consequently, the proposed volumetric heat source model adapts to changes in the local melt pool conditions due to scanning strategy and part geometry by dynamically adjusting the heat source depth and absorption. We demonstrate the capabilities of the proposed model through comparisons with a collection of experiments from the Additive Manufacturing Benchmark (AMBench).

36 MATERIALS SCIENCE↗

DOE OSTI2024

Phase Selection During Solidification and Solid-State Phase Transformations in an Al-10Ce-8Mn (wt pct) Alloy

In multicomponent Al-Ce alloys, and especially after additive manufacturing (AM), complex and metastable solidification microstructures are frequently observed. Here, in this research, the relationship between solidification conditions and phase selection are explored for an Al-10Ce-8Mn (wt pct) alloy using a systematic study of laser melting conditions. Three solidification modes were observed: primary Al 10 Mn 2 Ce; primary Al 20 Mn 2 Ce; and eutectic FCC Al + Al 20 Mn 2 Ce. These solidification modes were correlated to specific liquid-solid interface velocities using a simple thermal model, showing the change in primary solidification phase for low (< 6.8 × 10 −4 m/s), moderate (between 8.2 × 10 −4 and 5.9 × 10 −2 m/s) and high solidification velocities (> 6.2 x 10 −2 m/s) for the above three solidification microstructures, respectively. These results were rationalized by using interface response function (IRF) theory to describe the solidification undercooling for the possible primary intermetallic phases. The implication of the local phase selection from differing solidification conditions is summarized by a comparison of hardness which demonstrates the potential variance of Vickers hardness from 101 to 242 (VHV) by changing the laser velocity from 1 to 83 mm/s. Interestingly, on heat treatment at 400°C, the decomposition pathways of the solidification microstructure and hardness were also found to be different, thereby opening multiple pathways for spatial microstructure and property control within AM components.

Sisco, Kevin↗

DOE OSTI2024

Improving Additive Manufactured Component Performance through Multi-Scale Microstructure Simulation and Process Optimization

The purpose of this project was to utilize computational tools to understand the relationships between processing, microstructure, and properties for additively manufactured (AM) aluminum alloys for automotive applications, and to provide an engineering solution for helping to optimize process conditions. The project leverages ORNL developments in computational modeling, including AM process modeling, phase-field based microstructure evolution predictions, and data analytics techniques for mapping process conditions to material outcomes. The project utilized an Al-Cu-Mn-Zr alloy as a model material for studying formation of defects and microstructural features in response to variations in process conditions. Based on both pre-existing experimental data and simulation results, statistical process maps were constructed to identify regions of process space with minimal defect formation and advantageous microstructures and properties. The software tools used for this purpose were successful disseminated to GM, who were able to successful compile the relevant HPC codes within their own computing ecosystem and perform initial calculations to reproduce ORNL results.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Dual X-ray computed tomography-aided classification of melt pool boundaries and flaws in crept additively manufactured parts

In metal additive manufacturing (AM), understanding the process-structure-performance relationships requires a combination of multi-scale characterization techniques that allows for the measurement of the melt pool shape and boundary and classifying various defects and flaws in the AM parts. Such approaches can be destructive, only 2D in nature, or have a small field of view and can be complex to co-register and analyze. Here, in this work, we present a non-destructive 3D inspection technique that employs dual-energy X-ray computed tomography (XCT) along with a model-based iterative reconstruction (MBIR) and a new segmentation algorithm. The proposed approach and algorithm are not only capable of classifying and quantifying flaws such as pores, cracks, and inclusions, but they also allow for the extraction of microstructural features such as melt pool boundaries (MPB) and melt pool regions (MPR), that can help understand process-structure-performance relationships for alloys under study. As an exemplar application, we employed the method for characterization of an additively manufactured aluminum alloy crept under tensile stress at 300 °C for 1064 h. Our results demonstrate high quality segmentation and classification of various flaws and MPB and MPR, for the first time, using 3D X-ray CT inspection. The delineated MPB and MPR in the crept samples reveal the preferential growth paths of cracks that formed during creep deformation. The technique was used for successfully quantifying the characteristics (number of defects, their density, volume fraction, etc.) of the manufacturing-induced pores and creep-induced cracks, which is necessary to better understand the creep failure mechanisms of the material.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Equilipy: a python package for calculating phase equilibria

The CALPHAD (CALculation of PHAse Diagram) approach (Nigel Saunders & Miodownik, 1998) provides predictions for thermodynamically stable phases in multicomponent-multiphase materials across a wide range of temperatures. Consequently, the CALPHAD calculations became an essential tool in materials and process design (Luo, 2015). Such design tasks frequently require navigating a high-dimensional space due to multiple components involved in the system. This increasing complexity demands high-throughput CALPHAD calculations, especially in the rapidly evolving field of alloy design. In response to the need, we developed Equilipy an open-source Python package designed for calculating phase equilibria of multicomponent-multiphase systems. Equilipy is specifically tailored for high-throughput CALPHAD calculations, offering parallel computations across multiple processors and nodes with the given NPT input conditions namely elemental compositions (N), pressure (P), and temperature (T). Equilipy utilizes the program structure and Gibbs energy functions from the Fortran-based program, Thermochimica (Piro et al., 2013), with incorporating a new Gibbs energy minimization algorithm. This algorithm, originally developed by Capitani and Brown in 1987 (Capitani & Brown, 1987), has been revised and implemented to enhance the stability and performance of calculations. The Fortran codes are precompiled and interfaced with Python via F2PY, ensuring high computation speed. Benchmark tests shown in Figure 1 demonstrate that Equilipy’s computation speed is comparable to those of established commercial software, TC-Python and PanPython. This result highlights its efficiency and potential applications in various scientific and industrial fields.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2024

Preliminary Results on Process Modeling Tools for Determining Variability in Additively Manufactured Stainless Steel 316 Parts

The Advanced Materials and Manufacturing Technologies program aims to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy. However, the distinct characteristics of additive manufacturing (AM) materials, stemming from their unique processing history, microstructure, and properties, pose significant challenges for the qualification and certification of nuclear components. These challenges primarily arise from component-scale variations in microstructure and properties influenced by local process conditions and geometry, which affect thermal history, melt pool dynamics, and microstructure evolution. Computational modeling tools can play a crucial role in predicting and controlling this variability. This report presents preliminary results on process modeling tools designed to predict microstructure variability in additively manufactured stainless steel 316 parts. It details the software packages and physical modeling approaches employed to simulate an AM component within an automated process modeling workflow. Initial results are demonstrated through comparisons between predicted microstructures and experimental measurements across various representative processing conditions. The report concludes by discussing the challenges inherent in process modeling of AM components and outlines a plan for future development needs.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Effect of microalloying additions on microstructural evolution and thermal stability in cast Al-Ni alloys

Enhancement of thermal stability in Al-Ni alloys through microalloying with slow-diffusing elements, specifically Zr, has been previously reported which is attributed to Zr segregation at the Al/Al 3 Ni interface. In this study, we explore the influence of microalloying Al-Ni alloys with Zr, Ti, V, and Fe on microstructural evolution, hardness, and electrical and thermal conductivity across a range of heat-treatment temperatures from 300 to 450 °C. The distribution of microalloying elements and precipitates after heat treatment is characterized using atom probe tomography (APT). Our investigation confirms Zr segregation to the Al/Al 3 Ni interface, while similar interfacial segregation is absent with the addition of Ti, V, and Fe. Additionally, our analysis of the Al 3 Ni microfiber morphology reveals that their coarsening and spheroidization rates are similar with and without interfacial segregation; thus, retaining the fiber reinforcement through interfacial segregation of slow diffusing elements may not be an effective strategy. Precipitation of L1 2 nanoparticles was found to be the dominant mechanism affecting enhanced hardness and electrical conductivity in Al-Ni-Zr alloys, attributed to precipitation strengthening and solute depletion, respectively. Similar precipitation was not observed for additions of Ti, V, and Fe following heat treatment. We provide a thermodynamic explanation for this limitation. Furthermore, the findings of this study suggest that an effective approach for designing Al-Ni alloys should involve prioritizing microalloying elements to maximize L1 2 precipitation and minimize solute content in the FCC-Al matrix post heat treatment, rather than focusing on Al/Al3Ni interfacial segregation.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Creep deformation and cavitation in an additively manufactured Al-8.6Cu-0.4Mn-0.9Zr (wt%) alloy

Creep deformation and cavitation were investigated at 300 ºC in both tension and compression for an additively manufactured Al-8.6Cu-0.5Mn-0.9Zr (wt%) alloy in the as-fabricated state and after various aging treatments (aging at 300 °C/200 h or 350 °C/24 h and overaging at 400 °C/200 h). Creep mechanisms at 300 °C were determined by relating the measured creep response to corresponding microstructural and X-ray computed tomography observations. In compression, alloys in the as-fabricated and two aging conditions exhibited similarly high creep resistance. Overaging (400 °C/200 h) led to substantial coarsening of intragranular θ-Al2Cu precipitates and an expected drop in their Orowan strengthening contribution. In tension, minimum strain rates comparable to those in compression were obtained at any given stress; however, upon accumulation of some plastic strain in the matrix, creep cavities started to form, leading to accelerated tertiary stage creep deformation and rupture. Cavitation occurred exclusively along melt pool boundaries due to locally enhanced diffusion enabled by (i) large grain-boundary area in adjacent fine-grained zones and (ii) localization of creep strain in nearby heat-affected zones. Although cavity growth was initially diffusion-controlled, its rate was determined by matrix creep rate, consistent with constrained cavity growth mechanisms. This study reveals how microstructural complexities induced by the additive manufacturing process affect the creep and cavitation behavior of Al-Cu-Mn-Zr alloys. The underlying creep and cavitation mechanisms uncovered in this study point to pathways that improve the high-temperature properties of additively manufactured alloys.

36 MATERIALS SCIENCE↗

DOE OSTI2024

DECA: Discrete Event inspired Cellular Automata for grain structure prediction in additive manufacturing

Microstructure largely dictates macroscopic material properties and is strongly affected by processing. Therefore, the simulation of microstructure evolution in response to thermal fields during processing is of significant interest within the computational materials science community. Additive manufacturing (AM) has emerged as a technique for producing complex geometries and unique microstructures. Yet, complex and rapid thermal cycles in AM pose computational challenges for existing microstructure models. This work proposes a discrete event inspired cellular automata (CA) approach, titled DECA, to accelerate simulation of grain structure evolution in AM. In contrast to conventional time-stepped CA models, this model directly solves the times capture events would take place allowing for stepping in events rather than time (a technique also found in the field of discrete-event simulation). In comparison to purely serial discrete-event models, DECA allows for temporary violation of the causality constraint, but detects and corrects these violations, leading to an emergent phenomenon dubbed causality rippling, in which previously calculated capture events are overwritten. The amount of repeated calculations, defined by the capture ratio, is taken as a measure of computational inefficiency, and the model parameters that affect this ratio are evaluated. The new DECA approach was found to be more computationally efficient than conventional time-stepped CA models while guaranteeing an accurate solution, which can only be achieved in the conventional models for vanishingly small time steps. Finally, opportunities for parallelization and scaling of the new approach are discussed.

36 MATERIALS SCIENCE↗

DOE OSTI2024

An additively manufactured near-eutectic Al-Ce-Ni-Mn-Zr alloy with high creep resistance

A new additively manufactured (AM) Al-7.5Ce-4.5Ni-0.4Mn-0.7Zr (wt.%) near-eutectic alloy is reported, which shows unprecedented creep resistance up to 400 °C (a homologous temperature of 0.72). The eutectic solidification microstructure comprises ~ 27 vol% of coarsening-resistant second phase network with an ultrafine (<100 nm) inter-phase spacing. Both Mn and Zr contribute to creep resistance of the alloy. Small amount of Mn addition promotes selection of coarsening resistant phases without compromising the alloy processability. Zr not only improves hot-tearing resistance, but further enhances the second phase coarsening resistance resulting in improved creep resistance. Neutron diffraction performed during creep deformation reveals that the underlying mechanism for creep resistance in this alloy is impedance to dislocation motion stemming from the ultrafine eutectic solidification microstructure, whereas load transfer strengthening becomes less effective as the creep temperature increases. The second phase forms a continuous network in the as-fabricated condition, which is maintained during long-term creep at 300 °C. However, this network is fragmented into fine dispersoids at higher temperatures. It is proposed that the rate-limiting deformation mechanism at 300–400 °C is (i) dislocation climb for the alloy with fragmented second phase dispersoids and (ii) Orowan looping for the alloy with a continuous second phase network. In conclusion, the present design of an AM-processable multicomponent eutectic alloy with high creep resistance can be applied to other metallic systems exhibiting eutectic reactions, with expected extreme creep resistance.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Understanding solidification of near eutectic alloy using Cellular Automata (CA)

The solidification microstructure of an alloy strongly influences the mechanical properties. Dendritic and eutectic solidification are two important pathways of alloy solidification. The formation of phases, and their size and distribution depend on which pathway to take. In contrast to the Scheil model that has been widely used in describing the solidification pathways of alloys manufactured from conventional casting approach, more sophisticated solidification models are required to describe the state-of-the art manufacturing processes, such as additive manufacturing where distinctly different phase morphology, size and distribution than conventional casting can form, due to the vast difference in cooling conditions. Therefore, this work is to develop a computational Cellular Automata framework which includes the modeling of nucleation and growth of dendritic and eutectic solidification, as well as their competition as a function of alloy composition, undercooling and cooling rate. Further, after individual solidification models were validated against analytical solutions, the models were then combined to predict the competition between dendritic and eutectic solidification in alloys with off-eutectic compositions. This work predicts increased cooling rates suppress the dendritic solidification and promote eutectic solidification. Although quantitative validation is needed, this finding is consistent with qualitative observation in literature.

36 MATERIALS SCIENCE↗

DOE OSTI2024

High Strength Aluminum Additive Manufacturing

High-strength aluminum alloys for elevated temperature applications are desirable to replace heavier and more expensive titanium alloys. However, most aluminum alloys lose a large fraction of their strength at temperatures above approximately 200°C. ORNL has designed DuAlumin-3D, an alloy with nominal composition Al-9Ce-4Ni-0.5Mn-1Zr (wt.%), which utilizes the high cooling rates in additive manufacturing (AM) to achieve a refined microstructure, and thermally stable mechanical properties. DuAlumin-3D was fabricated by laser powder bed fusion and tested for its tensile mechanical properties across a range of temperature, and for its room temperature high-cycle fatigue resistance. The alloy was tested in both the as-printed and heat treated conditions, and both parallel and perpendicular to the AM build direction. The alloy was found to have anisotropic mechanical behavior in the as-printed state, but the anisotropy significantly decreased (both for tensile and fatigue properties) following heat treatment. The tensile properties significantly out-performed benchmark wrought 2219-T61 across a wide temperature range. The room temperature fatigue performance was approximately similar to 2219-T61.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Additively Manufacturing Nitinol Shape Memory Alloys for Advanced Actuator Designs

The objective of this research was to understand the role of feedstock production in the phase transformation behavior of additively manufactured Ni-Ti alloys for advanced actuator design. Industrial adoption of additively manufactured Ni-Ti alloys depends on the ability to produce repeatable phase transformation behavior, quantified here by the austenite to martensite transformation on heating. Small variations in the alloy composition may have a significant effect on the temperature at which this transformation occurs. This project showed that the powder characteristics play an important role in determining this behavior. Increases in the surface area per unit volume of the powder, either as a function of size distribution or morphology, have the effect of reducing the Ti content in the alloy through the formation of Ti-rich oxides on the powder surface, which has the effect of depressing the transformation temperature. Preferential Ni vaporization during additive manufacturing can partially offset this effect. To achieve repeatable results, it is important to understand the effect of powder oxidation, and to control the powder characteristics.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Grain Structure Evolution in Fe-6Si During Directed Energy Deposition

The purpose of this study is to explore the effect of additive manufacturing (AM) process variables on the grain structure of Fe-6Si, a soft-magnetic alloy used in electrical machine and grid applications. Samples were fabricated with laser engineered net shaping (LENS) with varying inter-pass timing and numbers of unidirectional passes. Here the results show that the grain structure was affected by both solidification and solid-state grain growth mechanisms. A model of the LENS process suggests that, although shorter inter-pass times encourage greater nucleation of new grains and therefore grain refinement during solidification, these conditions also help maintain high solid-state temperatures that allow for grain boundary motion to keep pace with the build rate. Grains formed under these conditions may span multiple layers, and the high-temperature gradient promotes directional growth. This new understanding of these microstructure evolution mechanisms will aid in using process conditions to control the competition between solidification and solid-state grain growth to create grain structures that may not be possible with conventional processing.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Microstructure and strengthening of Al-6Ce-3Ni-0.7Fe (wt%) alloy manufactured by laser powder-bed fusion

In this study, an Al-6Ce-3Ni-0.7Fe (wt%) alloy was fabricated via laser powder-bed fusion and its microstructure, thermal stability, tensile properties, and creep properties are investigated for two rapid-solidification rates with different eutectic spacings. For both faster- and slower-cooled states, the as-fabricated alloy mostly shows elongated grains with very fine eutectic networks (~40 nm lamellar width) comprising a high-volume fraction (~18 %) of intermetallic phases. Faster-cooled samples, however, display a less continuous eutectic network with finer spacing (~100 nm), leading to higher Orowan strengthening and therefore superior microhardness and yield stress up to ~350 °C. Upon aging (300 - 450 °C), micron-size Al 9 (Ni,Fe) 2 needle-like precipitates form within grains, and the Al 11 Ce 3 eutectic network spheroidizes, while retaining a submicron width and spacing, resulting in 33–37 % drop in microhardness after 144 h aging at 400 °C. Limited tensile ductility (~6 %) and creep ductility (~1-2 %) are measured for both faster- and slower-cooled alloys due to an inhomogeneous microstructure, where cavitation preferentially initiates at melt-pool boundaries, precipitate-free zones, and/or denuded zones, eventually leading to local fracture. Denuded zones, induced by stress, form due to diffusional flow with stress-dependent orientations, and are identified as microstructurally weak regions leading to strain localization. The present alloy does not show a significant difference in 300 °C creep resistance between: (i) tensile and compressive loading, (ii) faster- and slower-cooled samples, and (iii) continuous and spheroidized eutectics. Creep resistance at 300 °C is comparable to that of a Ce-richer Al-10.5Ce-3.1Ni-1.2Mn (wt%) alloy, despite the formation of denuded zones and needle-like Al 9 (Ni,Fe) 2 precipitates.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Leveraging the digital thread for physics-based prediction of microstructure heterogeneity in additively manufactured parts

A major limitation of additive manufacturing (AM) processes is that local conditions of material deposition frequently lead to unintentional heterogeneities in microstructure and properties within a single component, despite nominally uniform process conditions. Up to now, there has been no way to a priori determine the distribution of these heterogeneities, requiring expensive trial-and-error approaches to fabrication, testing, and characterization. Here, a physics-based framework for creating a digital representation of the laser powder bed fusion (PBF) process is proposed to predict the variation in solidification behavior that leads to heterogeneous microstructures in an as-built part. By leveraging in situ process data stored in the part’s digital thread, the scan path and process parameters were input into a heat transfer model which predicted solidification data at the melt pool scale. A two-step unsupervised clustering algorithm was used to first cluster the local solidification conditions (12.5µm 3 voxels) and then to cluster the regional behavior on the scale of multiple scan passes and print layers (250µm 3 super-voxels). This process was used to identify regions with similar solidification characteristics for multiple locations in a Stainless Steel 316-L component. The corresponding as-built part was sectioned and characterized using electron backscatter diffraction (EBSD). Quantitative analysis of the pole figures confirmed that the predicted regions of heterogeneity in the solidification conditions corresponded with differences in the observed microstructure. In conclusion, this work shows a viable path for estimating the microstructural heterogeneity for additively manufactured parts to either limit microstructural variation throughout a part or to enable functionality-based variation of the microstructure.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Local Modification of Cast Aluminum Alloys via the Cast-and-Print Process

Casting of aluminum alloys is a cost-effective way to mass manufacture bulk aluminum parts for automotive applications. However, the casting process requires filling of a mold, which imposes some limitations on the geometries that can be successfully cast and limits parts to be a uniform material. Therefore, we proposed that a hybrid casting plus additive manufacturing approach, Cast-and-Print, which could be used to locally modify the properties and geometry of cast parts to create difficult-to-cast, functional features. Here, we report the results of the properties of deposited materials on cast substrate, the properties of the interface of the deposited and cast material, and the application of the Cast-and-Print method to deposit rivet tabs on high-pressure die cast plates. Ultimately, the approach appears viable, but there are engineering challenges present to reliable additive processing of aluminum wires that need to be overcome for successful implementation of the technology.

42 ENGINEERING↗

DOE OSTI2023

Investigation of Form-and-Print Processing of Wrought Aluminum Alloys for Industrial Applications

Conventional manufacturing of wrought aluminum alloys generally involves rolling and forming of sheets of aluminum into the finished product. While these processes rapidly produce parts, produced parts are inherently limited to uniform thicknesses, specific geometries, and homogeneous material properties. Localized processing of formed parts could help overcome some of the geometric limitations imposed by forming, as well as allow for the possibility for localized property variation. Here, we present results from studies on the “Form-and-Print” process that uses additive manufacturing to locally deposit material where it is needed. In the context of these results, we discuss its viability for industrial applications and the key challenges facing the technology.

36 MATERIALS SCIENCE↗