Search NASA⌕ Search

Engineering topics

Poplawsky, Jonathan D.

Publications and source records attributed to Poplawsky, Jonathan D..

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A Mechanism for Carbon Depletion at Bondline of High-Frequency Electric-Resistance-Welded X70 Pipeline Steel

The bondline of electric-resistance-welded (ERW) linepipe steel, often etched white (i.e., ferrite) in optical microscopy, is generally believed to be carbon depleted. The mechanism for the carbon depletion, however, is not fully understood by researchers. To this end, here we used atom probe tomography (APT) to measure elemental segregation of the as-welded and post-weld heat-treated bondline regions of X70 linepipe welds. The thin vertical features at the bondline in the as-welded condition were identified as carbon-rich martensite-austenite (M-A) constituents, and the majority ferrite phase in the bondline was identified as carbon-depleted ferrite. Following the post-weld normalization, all alloying elements, except Nb and Mo, are homogenized across the bondline and heat-affected zone. The carbon depletion in the ERW bondline was accurately measured. A new mechanism for carbon depletion has been proposed using Scheil calculations of elemental partitioning during weld formation. Segregation of elements in the heat-affected zone was shown to follow the negligible partitioning local equilibrium (NPLE) kinetics for bainite transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The role of Si in determining the stability of the θ; precipitate in Al-Cu-Mn-Zr alloys

Precipitate-strengthened Al-Cu-Mn-Zr (ACMZ) alloys demonstrate improved microstructural stability compared to conventional Al-Cu alloys. Si is typically considered an impurity in these alloys, but a systematic analysis of ACMZ alloys with a range of Si levels revealed that there is a Si content range (~0.05 wt. % < Si < ~0.10 wt. %) for achieving optimal high temperature microstructural stability. A combination of hardness testing, scanning electron microscopy, and atom probe tomography has been used to understand the relationship between Si content, aging response, and thermal stability in ACMZ alloys. It is shown that the optimum Si content range corresponds to a reduced as-aged hardness, but a greater hardness value retained by the alloy after thermal exposure to 350 °C for 200 hours. A mechanism is proposed in which optimum Si levels reduce the number density of nucleation sites for θ' precipitates, resulting in larger precipitates that, on average, provide a reduced as-aged strength but are more coarsening resistant. This inherent θ' coarsening resistance allows more time for slow-diffusing Mn and Zr to reach the θ' interface and further stabilize the precipitates. Designing the optimal as-aged microstructure for improved thermal stability of the alloy by controlling impurity levels is a concept that has implications beyond the investigated Al-Cu alloy system.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Atomic structures of interfacial solute gateways to θ' precipitates in Al-Cu alloys

Many materials employed in critical structural applications depend upon metastable strengthening precipitates that transform or dissolve at elevated temperatures. Herein, aberration-corrected scanning transmission electron microscopy and first-principles calculations are used to accurately determine the atomic structure of the highly mobile, semi-coherent precipitate interfaces that control this process in the classic θ' (Al 2 Cu) precipitate in the Al-Cu system. Semi-coherent {110} interfaces are found to be composed of an array of unexpected misfit dislocations that are arranged in two different structural units. Dislocations accommodate nearly all of the misfit between the Al matrix and strengthening phase. Cu is observed to segregate to the compressed edge of the dislocation cores at specific sites in this interface. First-principles calculations revealed the energetic landscape that facilitates these sites to become entry and exit gateways of Cu atoms in this semi-coherent interface. In conclusion, this investigation reveals critical features within semi-coherent interfaces that determine the thermal stability of precipitation-hardened alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Examining the creep strengthening nanoprecipitation in novel highly reinforced heat resistant steels

Here we studied the creep strengthening nanoprecipitation in novel heat resistant steels strengthened by a high density of stable nanoprecipitates. The results show that the high number density of MX nanoprecipitates within the martensitic laths in these steels comes from the great amount of MX former elements present in their chemical compositions and the high dislocation density generated by the martensitic transformation that takes place during cooling after austenitization. These dislocations act as nucleation sites for these nanoprecipitates during the tempering applied after the austenitization and quenching. Atom probe tomography measurements show that these nanoprecipitates are rich in Nb, V, Cr and N for the HDSN1 and HDSN2 steels and V, Cr and N for the HDSN3 steel. The distribution of the nanoprecipitates within the martensitic laths suggests that the creep strengthening produced by the Nb, V, Cr and N nanoprecipitates in the HDSN1 and HDSN2 steels is more effective at pinning dislocations at high temperature than that obtained in the HDSN3 steel by the V, Cr and N nanoprecipitates. However, the high amount of W in the HDSN3 steel enhances the solid solution strengthening at high temperatures, resulting in a similar high temperature strength for all HDSN steels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Effects of niobium and tantalum on the microstructure and strength of ferritic-martensitic steels

Herein, detailed investigations of two ferritic-martensitic steels, i.e., Nb- and Ta-steel, indicate that the higher Nb diffusivity and the lower nucleation driving force of Nb-carbide promote preferential nucleation of Nb-carbides at grain boundaries and thus a higher boundary occupancy than Ta-carbides, which favored greater creep resistance of Nb-steel than that of Ta-steel despite their similar yield strength.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Irradiation-induced segregation at dislocation loops in CoCrFeMnNi high entropy alloy

To understand the redistribution of alloying elements in high entropy alloys under irradiation, we irradiated a CoCrFeMnNi alloy with 1 MeV Kr ions at room temperature and at 500°C, and characterized with atom probe tomography and transmission electron microscopy. At 500°C, Co and Ni were enriched around the interstitial, faulted and perfect, dislocation loops resulted from the ion irradiation. In contrast, no segregation was observed at room temperature. The inverse Kirkendall effect through vacancy flux, as opposed to the interstitial binding mechanism, was the primary underlying process attributing to the observed segregation. In addition, a ring-shaped segregation pattern was observed at the faulted dislocation loops, indicating a non-equilibrium nature of the defect clustering and solute segregation process in CoCrFeMnNi under irradiation at high temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Lattice-Distortion-Enhanced Yield Strength in a Refractory High-Entropy Alloy

Severe distortion is one of the four core effects in single-phase high-entropy alloys (HEAs) and contributes significantly to the yield strength. However, the connection between the atomic-scale lattice distortion and macro-scale mechanical properties through experimental verification has yet to be fully achieved, owing to two critical challenges: 1) the difficulty in the development of homogeneous single-phase solid-solution HEAs and 2) the ambiguity in describing the lattice distortion and related measurements and calculations. Here, a single-phase body-centered-cubic (BCC) refractory HEA, NbTaTiVZr, using thermodynamic modeling coupled with experimental verifications, is developed. Compared to the previously developed single-phase NbTaTiV HEA, the NbTaTiVZr HEA shows a higher yield strength and comparable plasticity. The increase in yield strength is systematically and quantitatively studied in terms of lattice distortion using a theoretical model, first-principles calculations, synchrotron X-ray/neutron diffraction, atom-probe tomography, and scanning transmission electron microscopy techniques. These results demonstrate that severe lattice distortion is a core factor for developing high strengths in refractory HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Fabrication and Characterization of Composite Membranes for the Concentration of Lithium Containing Solutions Using Forward Osmosis

In this study, an energy and highly time efficient, cost effective, and scalable forward osmosis (FO) composite polyvinylidene fluoride (PVDF) membrane is developed to concentrate lithium chloride recovered from naturally occurring geothermal brine resources. Dense thin robust defect-free Kynar-PVDF membranes are fabricated on porous PVDF hollow fiber supports. Various membrane fabrication parameters such as membrane thickness, coating solution concentration, cross-linker concentration, and curing temperature are studied to develop a defect-free dense membrane. Advanced characterization tools such as FIB-SEM, Raman, FTIR spectroscopy, and XRD are used to study the surface and cross-sectional morphology, chemistry of crosslinking, crystallinity and chemical structure of the dense PVDF membrane. FO is utilized to concentrate LiCl in the solution from 36 to 175 g L -1 with an average water transfer rate of 0.450 L m -2 h -1 (LMH) at 85 °C. Furthermore, the membrane showed stable performance for more than 550 h while maintaining the purity of the concentrated lithium chloride solution of >99.99 wt%. Overall, the results suggest that the FO-based technology is an innovative, time and energy efficient approach compared to the conventional technologies for concentration of battery grade LiCl for application in lithium ion batteries and other clean energy technologies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Perspectives on Quenching and Tempering 4340 Steel

Steels are ubiquitous due to their affordability and the landscape of useful properties that can be generated for engineering applications. But to further expand the performance envelope, one must be able to understand and control microstructure development by alloying and processing. In this paper we use multiscale, advanced characterization to better understand the structural and chemical evolution of AISI 4340 steel after quenching and tempering (Q&T), including the role of quench rate and short-time, isothermal tempering below 573 K (300 °C), with an emphasis on carbide formation. We compare the microstructure and/or property changes produced by conventional tempering to those produced by higher temperature, short-time “rapid” tempering. We underscore that no single characterization technique can fully capture the subtle microstructure changes like carbon redistribution, transition carbide and/or cementite formation, and retained austenite decomposition that occur during Q&T. Only the use of multiple techniques begins to unravel these complexities. After controlled fast or slow quenching, η transition carbides clearly exist in the microstructure, likely associated with autotempering of this high martensite start temperature (Ms) steel. Isothermal tempering below 598 K (325 °C) results in the relief of carbon supersaturation in the martensite, primarily by the formation of η transition carbides that exhibit a range of carbon levels, seemingly without substitutional element partitioning between the carbide and matrix phases. Hägg transition carbide is present between 300 °C and 325 °C. After conventional tempering at or above 598 K (325 °C) for 2 h, cementite is predominant, but small amounts of cementite are also present in other conditions, even after quenching. Previous work has indicated that silicon (Si) and substitutional elements partition between the cementite, which initially forms under paraequilibrium conditions, and the matrix. Phosphorous (P) may also be preferentially located at cementite/matrix interfaces after high temperature tempering. Slower quench rates result in greater amounts of retained austenite compared to those after fast quenching, which we attribute to increased austenite stability resulting from “autopartitioning”. Rapid, high temperature tempering is also found to diminish tempered martensite embrittlement (TME) believed to be associated with the extent of austenite decomposition, resulting in mechanical properties not attainable by conventional tempering, which may have important implications with respect to industrial heat treatment processes like induction tempering. Controlling the amount and stability of retained austenite is not only relevant to the properties of Q&T steels, but also next-generation advanced high strength steels (AHSS) with austenite/martensite mixtures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Nitrogen effects on radiation response in 12Cr ferritic/martensitic alloys

Ferritic/martensitic steels are one of the best candidates for structural materials for high dose applications in next generation nuclear reactors. The composition of structural materials must be optimized for reliable service during irradiation. This study reports the effect of interstitial nitrogen on radiation response in 12Cr ferritic/martensitic HT9 steels having a controlled nitrogen concentration. Results show that a high amount of ‘free’ nitrogen in the matrix stabilizes the interstitial clusters which leads to (i) larger loop sizes (ii) lower loop density and (iii) slightly reduced radiation induced hardening. It also affects diffusion mechanism of Ni and formation of Ni/Si-rich precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Partitioning of tramp elements Cu and Si in a Ni-based superalloy and their effect on creep properties

An alloy's processing history, including melting, remelting or the choice of stock material, affects its purity and eventually involves tramp element pickup or retention. Herein, variants of a novel Ni-based superalloy were manufactured with different levels of purity. The so-called low purity alloys contained 0.138 wt. % Cu and 0.019 wt. % Si while the Cu and Si levels were below x-ray fluorescence (XRF) detection limits of 0.003 and 0.010 wt. %, respectively, in the high purity ingots. Atom-probe tomography (APT) was carried out and revealed Si partitioning at the following interfaces: grain boundaries, MC carbide/γ, M 3 B 2 boride/$γ$ and M 3 B 2 boride/$γ$'. Copper was found to primarily segregate to the $γ$' precipitates. An average of 2.4 × decrease in creep life and 4.3 × decrease in creep ductility was measured in the low purity alloys, which was attributed to the embrittlement caused by Si segregation to grain boundaries. Furthermore, the positive effect of B on the creep properties was mitigated by the presence of Si. Thermodynamic predictions for the matrix and γ' precipitate compositions represented the trends observed experimentally although the extent of preferential partitioning lacks accuracy. Monte Carlo simulations were performed to describe the partitioning of Cu and Si atoms to either $γ$ or $γ$' phases.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupling computational thermodynamics with density-function-theory based calculations to design L12 precipitates in Fe Ni based alloys

Achieving a high-volume fraction of thermodynamically stable L12-type precipitates that are resistant to coarsening is of great importance for the development of low-cost FeNi based austenitic steels. With the aid of computational thermodynamics, this work designed two model alloys: Fe-37.4Ni-6.1Al-2.9Ti (FNAT) and Fe-45.2Ni-5.9Al-8.5Si (FNAS). Both alloys were designed to contain a similar amount of L1 2 precipitate in Fe-Ni matrix without forming other precipitates. Density-Function-Theory (DFT) calculation was coupled with computational thermodynamics to predict the critical radius at which the precipitates change shape from spherical to cuboidal. The calculation results suggest that critical radius for the FNAT alloy is about two orders of magnitude larger than that for the FeNiAlSi alloy. Phase stability and morphology of the L1 2 precipitates in these two alloys were experimentally investigated through X-ray diffraction, atom probe tomography, and scanning and transmission electron microscopy. The L1 2 precipitates in the FeNiAlSi system were found to be cuboidal and rod shaped, with much larger size than the spherical ones in the FeNiAlTi system, agreeing with the calculation results. This work suggested that coupling computational thermodynamics with DFT calculations can be reliably used to design L1 2 precipitates in FeNi based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The synergistic role of Mn and Zr/Ti in producing θ'/L12 co-precipitates in Al-Cu alloys

Microstructural stability is a critical factor to consider when designing new alloys for high-temperature applications. An Al-Cu alloy with Mn and Zr additions has recently been developed to withstand extended exposures of up to 350 °C. The addition of Mn in combination with Zr and their segregation to precipitate interfaces play a significant role in stabilizing the metastable θ ' precipitates responsible for the alloy&#x27;s hardness; however, adding Zr and Mn separately only improves the stability to 200 °C and 300 °C, respectively. To this end, the effect of the synergistic additions on interfacial structure and chemistry was studied in detail using atom probe tomography (APT) and scanning transmission electron microscopy (STEM) for Al-Cu-Mn-Zr/Ti-containing alloys subjected to long-term annealing (up to 2,100 h) in the critical temperature range, 300 °C and 350 °C, to investigate the role of Zr/Ti in increasing the θ '-precipitate stability. The APT and STEM results reveal that Mn additions stabilize θ ' long enough for the slower diffusing Zr atoms to segregate to coherent θ ' interfaces that eventually create a θ '/ L1 2 -Al 3 (Zr x ,Ti 1-x ) co-precipitate structure. The co-precipitate is highly stable, as shown by density functional theory calculations, and is a key factor that governs microstructural stability beyond 300 °C. This study reveals how solute additions with different stabilization mechanisms can work in concert to stabilize a desired microstructure, and the results provide insights that can be applied to other high-temperature alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural damage and phase stability of Al 0.3 CoCrFeNi high entropy alloy under high temperature ion irradiation

In this study, an initially single phase high entropy alloy (HEA) Al 0.3 CoCrFeNi was irradiated by 3 MeV Au ions to a fluence of 6 × 10 15 cm –2 (~31 dpa at damage peak) at four different temperatures ranging from 250 °C to 650 °C. Transmission electron microscopy (TEM) and Atom probe tomography (APT) were employed to study the evolution of structural damage and phase stability with irradiation temperature. Al 0.3 CoCrFeNi exhibited a similar evolution of irradiation-induced defects with temperature as compared with conventional FCC alloys. At 250 °C and 350 °C, most of the visible irradiation-induced defects were faulted 1/3$\langle{111}\rangle$ dislocation loops. As the irradiation temperature increased to 500 °C, perfect 1/2$\langle{110}\rangle$ dislocation loops were observed along with the faulted loops. At the highest irradiation temperature 650 °C, only dislocation lines and networks could be observed. Regarding phase stability, the 3 MeV Au irradiation was observed to suppress the precipitation of (Ni, Al)-enriched nano clusters and the L12 ordered structure at irradiation temperatures 250 °C to 500 °C whereas precipitation of the B2 ordered structure was accelerated at 650 °C. This resulted in qualitatively opposite precipitation behavior between the ion irradiated damage region and unirradiated region at 500 °C and 650 °C. The opposite phase stability of the ion-irradiated damage region and unirradiated region at different temperatures is attributed to the competing effects of ballistic dissolution vs irradiation enhanced diffusion on precipitation.

36 MATERIALS SCIENCE↗