Search NASA⌕ Search

Engineering topics

Qin, Yan

Publications and source records attributed to Qin, Yan.

At least 19 records

The Intraplate Stress Field of West Africa

West Africa continues to host a growing number of low and intermediate-magnitude earthquakes (M2-5) along its passive margins, and its continental interior. Earthquake activity in these regions raises the need to comprehend the causes and the tectonic controls of the seismicity. Unfortunately, such studies are rare. Here, we apply single-station inversion techniques to constrain fourteen focal mechanisms, computed after compiling a set of high-quality waveforms. We describe the connection between seismicity, the contemporary stress field, anthropogenic activity and Holocene fault scarps in the region. Our results indicate transpressive stresses acting on the inherited brittle structures in the passive margins. We also observe a compressive regime in the intracontinental failed rifts. We attribute the seismicity to the reactivation of “weak” faults in the Neoproterozoic and Mesozoic failed rifts, the passive transform structures, and the intracratonic Precambrian brittle shear zones.

58 GEOSCIENCES↗

Suppressing strain propagation in ultrahigh-Ni cathodes during fast charging via epitaxial entropy-assisted coating

Surface reconstruction and the associated severe strain propagation have long been reported as the major cause of cathode failure during fast charging and long-term cycling. Despite tremendous attempts, no known strategies can simultaneously address the electro-chemomechanical instability without sacrificing energy and power density. Here we report an epitaxial entropy-assisted coating strategy for ultrahigh-Ni LiNi x Co y Mn 1-x-y O 2 (x ≥ 0.9) cathodes via an oriented attachment-driven reaction between Wadsley-Roth phase-based oxides and the layered-oxide cathodes. Further, the high anti-cracking and anti-corrosion tolerances as well as the fast ionic transport of the entropy-assisted surface effectively improved the fast charging/discharging capability, wide temperature tolerance and thermal stability of the ultrahigh-Ni cathodes. Comprehensive analysis from the primary and secondary particle level to the electrode level using multi-scale in situ synchrotron X-ray probes reveals greatly reduced lattice dislocations, anisotropic lattice strain and oxygen release as well as improved bulk/local structural stability, even when charging beyond the threshold state of charge (75%) of layered cathodes. Layered Ni-rich oxide cathodes are susceptible to challenges with surface reconstruction and strain propagation, limiting their cyclability. The authors propose a solution involving oriented attachment-driven reactions, utilizing Wadsley-Roth nanocrystals and layered oxide to induce an epitaxial entropy-assisted coating, effectively addressing these issues.

25 ENERGY STORAGE↗

Critical Contribution of Imbalanced Charge Loss to Performance Deterioration of Si-Based Lithium-Ion Cells during Calendar Aging

Increasing the energy density of lithium-ion batteries, and thereby reducing costs, is a major target for industry and academic research. One of the best opportunities is to replace the traditional graphite anode with a high-capacity anode material, such as silicon. However, Si-based lithium-ion batteries have been widely reported to suffer from a limited calendar life for automobile applications. Heretofore, there lacks a fundamental understanding of calendar aging for rationally developing mitigation strategies. Both open-circuit voltage and voltage-hold aging protocols were utilized to characterize the aging behavior of Si-based cells. Particularly, a high-precision leakage current measurement was applied to quantitatively measure the rate of parasitic reactions at the electrode/electrolyte interface. The rate of parasitic reactions at the Si anode was found 5 times and 15 times faster than those of LiNi 0.8 Mn 0.1 Co 0.1 O 2 and LiFePO 4 cathodes, respectively. Here, the imbalanced charge loss from parasitic reactions plays a critical role in exacerbating performance deterioration. In addition, a linear relationship between capacity loss and charge consumption from parasitic reactions provides fundamental support to assess calendar life through voltage-hold tests. These new findings imply that longer calendar life can be achieved by suppressing parasitic reactions at the Si anode to balance charge consumption during calendar aging.

25 ENERGY STORAGE↗

A Li-rich layered oxide cathode with negligible voltage decay

With high capacity at low cost, Li- and Mn-rich (LMR) layered oxides are a promising class of cathodes for next generation Li-ion batteries. However, substantial voltage decay during cycling, due to the unstable Li 2 MnO 3 honeycomb structure, is still an obstacle for their practical deployment. Here we report a Co-free LMR Li-ion battery cathode without voltage decay. The material has a composite structure consisting of layered LiTMO 2 and various stacked Li 2 MnO 3 components, where transition metal (TM) ions partially reside in the Li layers of Li 2 MnO 3 , serving as a “cap” to strengthen the stability of the honeycomb structure. This unique capped-honeycomb structure is persistent after high-voltage cycling and prevents TM migration and oxygen loss, as shown by experimental and computational results. Furthermore, this work demonstrates that the long-standing voltage decay problem in LMRs can be effectively eliminated by internally pinning the honeycomb structure, which opens an avenue to developing nextgeneration high-energy cathode materials.

25 ENERGY STORAGE↗

Microseismic Monitoring at the Farnsworth CO 2 -EOR Field

The Farnsworth Unit in northern Texas is a field site for studying geologic carbon storage during enhanced oil recovery (EOR) using CO 2 . Microseismic monitoring is essential for risk assessment by detecting fluid leakage and fractures. We analyzed borehole microseismic data acquired during CO 2 injection and migration, including data denoising, event detection, event location, magnitude estimation, moment tensor inversion, and stress field inversion. We detected and located two shallow clusters, which occurred during increasing injection pressure. The two shallow clusters were also featured by large b values and tensile cracking moment tensors that are obtained based on a newly developed moment tensor inversion method using single-borehole data. The inverted stress fields at the two clusters showed large deviations from the regional stress field. The results provide evidence for microseismic responses to CO 2 /fluid injection and migration.

02 PETROLEUM↗

Improving Subsurface Stress Characterization for Carbon Dioxide Storage Projects by Incorporating Machine Learning Techniques

The overall objective of this project is to develop a framework for reliable characterization and prediction of the state of stress in the overburden and underburden (including the basement) in CO 2 storage reservoirs using machine learning and integrated geomechanics and geophysical methods. Specifically, we propose to develop workflow encompassing of technologies and/or methods to predict stress and pressure changes due to CO 2 injection in an active tertiary recovery site and their impacts on subtle fault activation, fractures and occurrence of microseismic events and compare responses to field observations. In this project, we anticipate using dataset from the Farnsworth field Unit (FWU) which is operated by Purdure Petroleum. A novel elastic-waveform VSP inversion technique will be used to estimate high-resolution spatial and temporal changes of elastic moduli in CO 2 storage reservoirs, which will be combined with velocity-stress relationship derived from laboratory tests to obtain subsurface pressure and stress. Clustered microseismic data will be jointly inverted for improved focal mechanisms. Least-squares reverse-time migration of microseismic waveform data will be performed to directly image fracture/fault zones. Additionally, a deep neural network machine learning technique with convolutional and recurrent layers will be used for learning the spectro-temporal structures in microseismic waveforms. The results of this geotechnical data analysis will be integrated to develop a high-resolution 3D mechanical earth model extending from the overburden sealing formations to the underburden including the basement. Mechanical properties will be derived through integration of mechanical logs, tests, available results from chemo-mechanical laboratory tests, and elastic inversion of seismic data using a combination of Bayesian and stochastic methods as well as machine learning technique. Failure features (faults/fractures) will be represented and/or modeled based on seismic and core data analysis. A transient hydrodynamic-geomechanical model will be developed through coupling with the calibrated FWU reservoir simulation model. The full physics coupled model will be used to train a reduced order proxy model using machine learning algorithm for estimating stress which will then be used with appropriate constitutive relationships and forward seismological models to simulate pressure changes and induced microseismicity. An advanced optimization framework will be developed to perform a history match to minimize error between field observations and simulated. The history matched proxy model will be verified against the full-physics equivalent. The field observations that will be used in the coupled model calibration process include pressure/stress inverted from VSP, moment magnitude from microseismic analysis, real time downhole pressure measurements, production and injection data. Parameter sensitivity and uncertainty analysis will be performed to characterize the impact of model parameter uncertainty on stress estimates. The proposed project will have significant impact on future field implementation of the proposed technology. Because the project field site is an ongoing CO 2 EOR development, the value of the new technology will be demonstrated in an operational context and evaluated as a viable risk mitigation strategy. Cost/benefit will be evaluated together with the various commercial incentives for CO 2 sequestration available to oil and gas operators. The extensive available dataset and ongoing data acquisition under the SWP Phase III work plan provides flexibility for investigation of multiple approaches and reduces technical risk.

58 GEOSCIENCES↗

Influence of Fault Architecture on Induced Earthquake Sequence Evolution Revealed by High-Resolution Focal Mechanism Solutions

The increasing seismicity and improved seismic observation network in recent years provide an opportunity to explore factors that influence the triggering processes, spatiotemporal evolution, and maximum magnitude of induced sequences. We map the fault architecture and stress state of four induced sequences in Oklahoma to determine their influence on the seismicity. We systematically relocate the earthquakes and compute hundreds of focal mechanisms of small to medium events (1.0 < M < 5.1) using various techniques, including machine learning, for the Guthrie, Woodward, Cushing, and Fairview sequences. The detailed fault geometry and spatiotemporal evolution of seismicity and stress states reveal different dominant driving forces for each sequence. In Cushing and Fairview (largest event ≥M5.0), the main fault structures are near-vertical narrow strike-slip faults, with most of the small earthquake fault planes optimally oriented. The two sequences exhibit discontinuous temporal migration but strong earthquake self-driven rupture growth. In Guthrie and Woodward (largest event <M5.0), the two sequences show more complex diffuse fault structures with varying dipping angles along depth. The inverted focal mechanisms show a mix of strike-slip faulting and normal faulting in both sequences, and the normal faulting events are less optimally oriented than strike-slip events. The two sequences are dominated by continuous diffusive migration in time driven by pore pressure propagation. The above results suggest that fault architecture and stress state influence sequence evolution, major driving forces, and possibly maximum magnitude.

58 GEOSCIENCES↗

Enable High-Energy LiNi0.5Co0.2Mn0.3O2 by Ultra-Thin Coating through Wet Impregnation

A high cut-off voltage is required for nickel-rich layered oxide LiNixCoyMnzO2 (NCM) to meet the high energy density requirement of lithium-ion batteries in electric vehicles. However, such a high voltage application leads to an unstable interface between NCM and liquid electrolytes. To stabilize the interface, the facile wet impregnation method has been developed to apply an ultra-thin Al2O3 coating layer on the NCM particles. This coating layer was found to have a strong interaction with the NCM and resulted in Al-doped NCM at the surface structure of NCM. The change of surface structure can not only reduce the surface resistance of lithium diffusion of LiNi0.5Co0.2Mn0.3O2 (NCM523), but also stabilize the solid electrolyte interface between NCM523 and the electrolyte with the cut-off voltage of 4.5 V vs. Li/Li+. Compared to other coating methods, wet impregnation coating can provide an ultra-thin and uniform coating with surface doping on NCM particles. Furthermore, this scalable coating method can be applied to various electrode materials without adding much additional cost.

25 ENERGY STORAGE↗

Forecasting induced seismicity in Oklahoma using machine learning methods

Oklahoma earthquakes in the past decade have been mostly associated with wastewater injection. Here we use a machine learning technique—the Random Forest to forecast induced seismicity rate in Oklahoma based on injection-related parameters. We split the data into training (2011.01–2015.05) and test (2015.06–2020.12) periods. The model forecasts seismicity rate during the test period based on input features, including operational parameters (injection rate and pressure), geological information (depth to basement), and modeled pore pressure and poroelastic stress. The results show overall good match with observed seismicity rate (adjusted R 2 of 0.75). The model shows that pore pressure rate and poroelastic stressing rates are the two most important features in forecasting. The absolute values of pore pressure and poroelastic stress, and the injection rate itself, are less important than the stressing rates. These findings further emphasize that temporal changes of stressing rates would lead to significant changes in seismicity rates.

58 GEOSCIENCES↗

Research Introduction [Slides]

In the topic of Reverse Time Imaging, we proposed a new IC to reduce computation cost but reserve image resolution for distributed sensor networks. For Induced Seismicity in Oklahoma, we analyzed fault stress state analysis at state scale, and we applied machine learning techniques to polarity picking and seismicity rate forecasting. The results provide better understanding of fault properties, stress field, and the relationships among fault, stress state, injections, and potential seismic hazards. Lastly, for Microseismic Monitoring, we detected and located 770 low-frequency events (5-50 Hz): (1) Shallow events are highly clustered, consistent with the pathway from injection well 13-10A to monitoring well; moment tensor inversion shows dominant tensile cracking; (2) Deep events are scattered and show migration pattern to the basement; moment tensors show that most events are shear cracks.

58 GEOSCIENCES↗

Probing Thermal Stability of Li-Ion Battery Ni-Rich Layered Oxide Cathodes by means of Operando Gas Analysis and Neutron Diffraction

Thermal stability is a crucial parameter that must be considered within the overall performance metrics of Ni-rich layered oxide cathodes. While the intrinsic structural stability of the cathode materials under thermal conditions is important, it is also critical to consider their reaction with electrolytes. In this study, operando gas analysis, ex situ neutron diffraction, and differential scanning calorimetry were combined to give a broader picture of the thermal stability of Ni-rich NMC cathodes. Li 1– x Ni 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) composite materials with four different states of charge were investigated with and without the presence of an electrolyte. It has been found that electrolyte can greatly accelerate both the structural and thermal decomposition of the cathode materials. A higher state of charge will also make cathode materials more susceptible to thermal shock. Without an electrolyte, O 2 release inducing a structural change from layered to rock salt was the major observation during thermal runaway. However, all samples retained some levels of layered structure after annealing up to 300 °C without the electrolyte. In comparison, almost all the O3-type layered phase transformed to the rock-salt phase for the cathode materials heated with the electrolyte at the same experimental conditions. Moreover, the amount of CO 2 increased by nearly two orders of magnitude when annealing cathode materials with electrolyte in operando gas analysis experiments. More delithiated NMC811 samples released larger amounts of CO 2 at earlier onset temperatures, resonating well with the differential scanning calorimetry (DSC) results showing that more delithiated samples release more heat during thermal shock.

25 ENERGY STORAGE↗

Advanced electrolytes for fast-charging high-voltage lithium-ion batteries in wide-temperature range

LiNixMnyCo1-x-yO2 (NMC) cathode materials with Ni=0.8 have attracted great interest for application in high energy-density lithium (Li)-ion batteries (LIBs) because of their high specific capacities at high voltages. However, the practical application of Ni-rich NMC in LIBs under high charge voltages (e.g. 4.4 V and above) still faces big challenges due to the severe capacity fading, which is directly related to the instability of the cathode/electrolyte interface. In this work, we develop new localized high-concentration electrolytes (LHCEs) based on carbonate solvents, which are compatible with graphite (Gr) anode and have a high oxidation potential over 4.9 V vs. Li/Li+. The optimal LHCE enables the Gr||NMC811 cells with 2.8 mAh cm-2 cathode areal capacity loading to achieve an excellent cycling stability over 600 cycles with a capacity retention of 94.2 % under a charge cut-off voltage of 4.4 V at 25 ?C, good rate capabilities under fast charging or discharging up to 3C rate, and superior low-temperature discharge performance down to -30 ?C with a capacity retention of 85.6% at C/5 rate. The findings in this work shed light a very promising strategy to develop new electrolytes for practical high-energy LIBs with Ni-rich NMC cathodes.

Zhang, Xianhui↗

Optimization of Graphite–SiO blend electrodes for lithium-ion batteries: Stable cycling enabled by single-walled carbon nanotube conductive additive

Lithium-alloying materials are of great interest to improve the gravimetric and volumetric energy density of lithium-ion batteries, though their associated volume fluctuation with cycling often leads to poor cycling performance. Active-inactive alloys and blending alloys with carbon materials are common strategies to accommodate volume fluctuation. Herein we set out to optimize graphite-SiO blend electrode formulations to eliminate rapid capacity fade. Electrodes with highly stable cycling were prepared by simple planetary mixing procedures, enabled by the use of just a fraction of a weight percent of commercial SWCNTs as the only conductive additive, and by the appropriate choice of binder/stabilizing agent. In fact, the use of SWCNTs allowed for graphite-free SiO electrodes with approximately 74% higher volumetric energy density relative to traditional graphite electrodes, and superior capacity retention in coin-type full-cell testing versus NMC532 cathodes.

25 ENERGY STORAGE↗

Deciphering the Stress State of Seismogenic Faults in Oklahoma and Southern Kansas Based on an Improved Stress Map

Fault location and geometry are prime considerations in the reactivation of preexisting faults. Here, we combine relocated earthquake catalogs and focal mechanisms to delineate seismogenic faults in Oklahoma and southern Kansas and analyze their stress state. Initially, we identify and map seismogenic faults based on earthquake clustering. We then obtain an improved stress map using 2,047 high-quality focal mechanisms. The regional stress map shows a gradual transition from oblique normal faulting in western Oklahoma to strike-slip faulting in central and eastern Oklahoma. Stress amplitude ratio shows a strong correlation with pore pressure from hydrogeologic models, suggesting that pore pressure exhibits a measurable influence on stress patterns. Finally, we assess fault stress state via 3-D Mohr circles; a parameter understress is used to quantify the level of fault criticality (with 0 meaning critically stressed faults and 1 meaning faults with no applied shear stress). Our findings suggest that most active faults have near vertical planes (planarity >0.8 and dip >70°), and there is a strong correlation between fault length and maximum magnitude on each fault. The fault trends show prominent conjugate sets that strike [55–75°] and [105–125°]. A comparison with mapped sedimentary faults and basement fractures reveals common tectonic control. Based on 3-D Mohr circles, we find that 78% of the faults are critically stressed (understress ≤0.2), while several seismogenic faults are misoriented with high understress (>0.4). Fault geometry and local stress fields may be used to evaluate potential seismic hazard, as the largest earthquakes tend to occur on long, critically stressed faults.

58 GEOSCIENCES↗

Exploring the charge reactions in a Li–O 2 system with lithium oxide cathodes and nonaqueous electrolytes

Nonaqueous lithium–oxygen batteries have attracted considerable attention due to their high energy density. Huge efforts have been made to unravel the fundamentals of Li–O 2 battery chemistry. However, current Li–O 2 batteries still suffer from several unresolved problems such as the instability of electrolytes and sluggish oxidation of lithium oxides during the charging process. In this paper, we propose a detailed study to investigate the charge mechanism of lithium oxide materials in different electrolytes. Commercially available lithium peroxide and lithium oxide have been employed as cathodes to determine how lithium oxides (both lithium oxide and lithium peroxide) and electrolytes change during charge. Lastly, the result shows that Li 2 O 2 decomposed to lithium and oxygen; meanwhile, the electrolyte has a significant influence on Li 2 O 2 decomposition. Furthermore, while most of the Li 2 O material participates in side reactions with the electrolyte, some of it is found to delithiate and crumble in structure.

36 MATERIALS SCIENCE↗