Search NASA⌕ Search

Engineering topics

Qu, Jun

Publications and source records attributed to Qu, Jun.

At least 37 records · Page 2

Tribocorrosion of stainless steel sliding against graphite in FLiNaK molten salt

The molten salt reactor (MSR) concept recently gained renewed interest in developing Generation IV nuclear reactors. One MSR design uses fluoride molten salts to cool tri-structural isotropic particle fuel encapsulated by a carbon matrix into spherical pebbles, which would inevitably contact the reactor's stainless steel container wall during salt circulation. Characterizing this interaction is crucial for reactor safety. Here, in this work, we report the tribocorrosion behavior of graphite sliding against Type 316H stainless steel lubricated by a FLiNaK (LiF:NaF:KF; 46.5:11.5:42 mol %) molten salt in an argon environment. Accelerated wear loss was observed at a higher temperature because of a lower molten salt viscosity and a higher corrosion rate. The graphite had a more rapid material loss at a higher sliding speed than stainless steel because of its higher vulnerability to vibration-induced microfracture. The salt-starved condition caused more material loss than either the no-salt or the salt-flooded condition because neither a graphite transfer film nor stable boundary lubrication could be established at salt starvation. An interesting dual-layer surface film was discovered on the stainless steel worn surface: a chromium-rich top film and a nickel-accumulated but chromium-depleted interlayer. The film composition and structure provide fundamental insights to the mechanochemical interactions between stainless steel and graphite in a molten salt environment.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Improving knife milling performance for biomass preprocessing by using advanced blade materials

Mechanical preprocessing of biomass, including size reduction, is a crucial step in converting biomass into biofuel. However, feedstock inevitably contains abrasive intrinsic and extrinsic inorganics that may cause excessive tool wear in preprocessing. Here, this work demonstrates that performance of a knife mill can be significantly improved by applying a more wear-resistant blade material. A series of full-scale knife mill tests were performed for size reduction of forest residue using blades of tungsten carbide (WC–Co), iron-borided tool steel, and diamond-like carbon (DLC) coated tool steel. Blade material loss was quantified in correlation to the amount of feedstock processed and wear mechanisms were investigated via worn surface characterization. While the thin DLC coating was removed quickly, the WC-Co and iron-borided blades improved the tool life by 8X and 3X compared with the M2 tool steel blades (baseline), respectively. The in-situ throughput and power consumption measurements provided additional insights. The WC-Co and iron-borided blades had ~3X higher throughput than the baseline blades by the end of the test with lower normalized power consumption. The experimental results were then used as input for a techno-economic analysis, which suggested that the more wear resistant blades could cut the knife milling cost by $2–3 per ton of biomass processed with downtime reduced by 65–85%.

36 MATERIALS SCIENCE↗

Impact of Boron-Containing Lubricant Additive on Three-Way Catalyst Reactivity and Physicochemical Properties

Boron-containing compounds are one of the lubricant additive options due to their suitable properties for additives and have been used as commercial lubricant additives. In the present study, the impact of a boron-containing lubricant oil additive, AR9100 (BR), on Pd/Rh-based three-way catalyst (TWC) performance is investigated, and the results are compared with the baseline no-additive (NA) case and the industry standard zinc dialkyl-dithiophosphate (ZDDP) results. Accelerated engine aging is performed using a genset to expose the catalysts to lubricant additives at high temperatures. All aged TWC samples are investigated for reactivity in a bench-flow reactor and characterized using a variety of analytical techniques. Compared with the no-additive case, the temperatures of 90% conversion (T 90 ) of NO, CO, C 3 H 6 , and C 3 H 8 for the ZDDP-aged TWC sample increased by 34, 30, 37, and 48 °C. However, the T 90 of all gas species for the BR-aged TWC sample are similar to the NA-aged TWC sample. Additionally, a significant decrease in water–gas shift reactivity and oxygen storage capacity is observed in the ZDDP-aged sample, but not in the BR-aged sample. Inductively coupled plasma-optical emission spectrometry (ICP-OES) analysis and electron probe microanalysis (EPMA) maps of accelerated engine aging samples show the presence of phosphorus and boron in ZDDP- and BR-aged TWC samples, respectively. However, no boron-related peaks are observed in the X-ray diffraction (XRD) pattern of the BR-aged TWC sample, which may exist in the form of an amorphous phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Macroscale superlubricity by a sacrificial carbon nanotube coating

Superlubricity, i.e., coefficient of friction (COF) below 0.01, was earlier limited to microscale in controlled environments in the earlier literature and more recently realized for macroscale sliding of ceramic or carbon surfaces lubricated by water or other polar fluids. However, there is lack of report of superlubricity for the most common bearing system, i.e., steel-steel contact in non-polar oil lubrication. Here, in this work, we present ultra-low COF of 0.001–0.007 by using a sacrificial coating composed of vertically-aligned carbon nanotubes (CNTs) for macroscale steel-steel sliding under minimum quantity lubrication (MQL) of a polyalphaolefin (PAO) oil in the ambient environment. Raman spectroscopy and electron microscopy analyses detected graphene-containing tribofilms on both the steel surfaces, which was produced by the fractured CNT flakes and metallic wear debris during running-in. The in situ formed graphene-graphene contact interface presumably possesses a low shear resistance leading to superlubricity. The presence of oil, despite as little as one droplet, has proven to be crucial. Such a superlubricity performance has shown good sustainability in extended testing of more than 500,000 cycles and strong ability of accommodating changes in sliding conditions. Results here demonstrate feasibility with fundamental insights for achieving ambient environment macroscale superlubricity.

36 MATERIALS SCIENCE↗

Analysis of Cutter Blade Wear in Rotary Shear Mills

Following development of an analytical abrasive wear model to predict wear of components in a rotary shear mill, the team used a finite element analysis (FEA) approach to calculate forces and loads acting on particles responsible for abrasive wear. The analytical model related critical rotary shear process parameters (shear geometry and rotational speed) to critical material attributes of inorganic mineral species in feedstock (density, size, and aspect ratio) and substrate (hardness and elastic modulus) that enabled us to model the wear of shear cutters in a rotary shear milling system developed by Forest Concepts. With proper knowledge of the forces acting between abrasive particles and cutter components built into it, the model can accurately predict wear of the cutters and provides a quality by design (QbD) approach to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches. During this reporting period, researchers at Oak Ridge National Laboratory applied an FEA package to simulate the local stresses and forces between an abrasive silica particle and two rotary shear cutters as the distance between the cutters decreases. The output of the FEA was used to provide more accurate projections of the loads applied to the particles in the analytical wear model. Comparison of the FEA force calculations are in good agreement with the loads assumed in the analytical predictions.

36 MATERIALS SCIENCE↗

A Comparative Tribo-Mechanical Behavior Analysis of Laser Cladded Nitronic 60 Coating Against Wrought Nitronic 60 Alloy

In this study the tribological and mechanical behavior of a laser cladded Nitronic 60 coating on maraging steel is compared to that of a wrought Nitronic 60 alloy. A multi-layer Nitronic 60 coating was deposited using laser directed energy deposition, and its microstructure, porosity, and microhardness were characterized. The microhardness of the coated region in the laser cladded Nitronic 60 varied between 270-300 HV whereas that for wrought form was 230 HV. Controlled tribological tests under motor oil lubricated conditions were conducted at both room and elevated temperatures. The laser cladded Nitronic coating exhibited poorer wear resistance at room temperature but higher wear resistance at elevated temperature as compared to the wrought Nitronic alloy. Severe plastic deformation and fracture was observed on the laser cladded coating after the wear tests at both temperatures. Wear mechanisms were investigated based on the morphological and compositional characterization of the wear tracks.

36 MATERIALS SCIENCE↗

X-ray photoelectron spectroscopy of morpholinium ionic liquids: impact of a long alkyl side substituent on the cation–anion interactions

In this study, X-ray photoelectron spectroscopy is used to analyse nine morpholinium ionic liquids, which are of great interest in green chemistry because of their low toxicity and high recyclability. Here, the effect of the alkyl chain length on the aliphatic C 1s binding energy and the impact of the anion basicity on the cationic N 1s and O 1s binding energies are investigated. It is concluded that by changing the basicity of the anion, there is a more notable change in the electronic environment of the oxygen centre. The impact of a long alkyl side substituent on the cation–anion interactions is also discussed. It is observed that there is an intense charge shielding effect of the alkyl side chain in the cases of octyl and dodecyl substituents, which is reflected in the reduced Br 3d 5/2 binding energy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tribological Evaluation of Candidate Coatings

This SPP project with Novus was to investigate tribological properties of candidate ceramic composites. Systematic tribological bench tests and surface characterization were performed to determine composition-property relationships of several Zr-Ti-B based ceramic composites of different compositions. The lowest friction coefficient was measured with Ti0.6Zr0.4B2 composition tested in the hydraulic oil. Surface characterization suggests a formation of ZDDP tribofilm in the worn region when tested with a hydraulic oil. In all experiments, the ceramic composites did not have measurable wear, but caused material loss of the steel countersurface.

36 MATERIALS SCIENCE↗

Material Selection and Corrosion Studies of Candidate Bearing Materials for Use in Molten Chloride Salt

Molten chloride salts are being given strong consideration for use in heat transfer and storage in concentrating solar power (CSP) systems as well as in some nuclear reactor applications. Containment of the molten salt, particularly at the highest temperatures, is a major material concern and has received considerable study. Another material issue is the pumps that will be required to move the molten salt along with the bearing materials that will be required to have sufficient corrosion resistance as well as wear resistance in the high temperature salt. A pair of coordinated studies in our laboratory has addressed the corrosion, and the wear issues of candidate bearing materials including the selection of candidate materials as well as their performance in a molten sodium chloride-potassium chloride-magnesium chloride salt environment. This work addresses the selection of candidate materials and their chemical compatibility with the molten salt. The studies have identified material pairs that have suitable properties for use as bearings that would be immersed in molten chloride salt.

14 SOLAR ENERGY↗

Metal nanoparticles as lubricant additives

A lubricant composition comprising: (i) silver or gold nanoparticles, each of which is encapsulated by a layer of alkylthiol or alkylamine molecules; (ii) palladium or platinum nanoparticles, each of which is encapsulated by a layer of alkylthiol or alkylamine molecules; and (iii) a fluid in which components (i) and (ii) are present. Further described are methods for applying the lubricant composition onto a mechanical device for which lubrication is beneficial, with resulting improvement in friction and wear reduction and/or corrosion inhibition.

Ihala Gamaralalage, Chanaka Kapila Kumara↗

An antibody-free platform for multiplexed, sensitive quantification of protein biomarkers in complex biomatrices

Sensitive, multiplexed protein quantification remains challenging despite recent advancements in LC-MS assays for targeted protein biomarker quantification. High-sensitivity protein biomarker measurements usually require immuno-affinity enrichment of target protein; a process which is highly dependent on capture reagent and limited in capability to measure multiple analytes. Herein, we report a novel antibody-free platform, which measures multiple biomarkers from complex matrices employing a strategically optimized solid-phase extraction cleanup and orthogonal multidimensional LC-MS. Eight human protein biomarkers with different specifications were spiked into canine plasma as a model investigation system. The developed strategy achieved the desired sensitivity, robustness, and throughput via the following steps: (1) post digestion mixed-mode cation exchange-reverse phase SPE enrichment cleaned up the sample initially; (2) rapid, high-pH peptide fractionation further eliminated background components efficiently while selectively enriched signature peptides (SP) to provide sufficient sensitivity for multiple targets; and (3) trapping-micro-LC-MS analysis delivered high sensitivity comparable to a nano-LC-MS method but with much better robustness and throughput for the final analysis. Compared with a conventional LC-MS assay with direct protein digestion and limited clean-up, analysis with this antibody-free platform improved the LLOQ by 1–2 orders of magnitude for the eight protein biomarkers, reaching as low as 5 ng/mL in plasma, with feasible robustness and throughput. In conclusion, this platform was applied for the quantification of biomarkers of respiratory conditions in patients with various lung diseases, demonstrating real-world applicability.

59 BASIC BIOLOGICAL SCIENCES↗

Atomistic investigation of calcium sulfonate and lithium complex grease tribofilms under severe sliding conditions

We report innovative grease chemistries and additives are continuously developed to meet challenging applications such as wind energy bearings and offshore/underwater applications. The non-equilibrium and transient structures within interfacial tribofilms play an influential role in the service life of a component. Atom probe tomography and transmission electron microscopy studies were performed to investigate the tribofilms formed by lithium complex and calcium sulfonate grease thickeners. The study reveals that morphology, amorphicity, nanostructure, and atomic layering play an influential role in the exceptional wear and corrosion performance of calcium sulfonate thickeners.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of Cutter–Woodchip Contact Pressure in a New Biomass Comminution System

A Crumbler ® rotary shear system was recently developed to process fuel-grade woodchips into feedstocks having more uniform particle sizes for improved flowability and higher thermochemical output yield than a traditional hammer mill. It represents a significant innovation in the state of the art of biomass comminution equipment. However, the milling unit has experienced significant abrasive wear of the feeding teeth and cutters when processing hard and dusty feedstocks, such as logging residue and corn stover. Here, we present initial simulation results from a finite-element stress analysis of the rotary shear, which is used to investigate the dynamics of interaction between the cutters and woodchips. This is the first step for optimizing the cutter design to improve the system lifetime and processing efficiency, thus reducing downtime and improving overall productivity.

42 ENGINEERING↗

Grid-to-rod fretting wear study of SiC/SiC composite accident-tolerant fuel claddings using an autoclave fretting bench test

Grid-to-rod-fretting (GTRF) in pressurized water reactors (PWRs) is known to cause wear and surface damage on the fuel claddings, potentially leading to radioactive leakage. One of the accident-tolerant fuel (ATF) concepts is to use advanced cladding materials that could withstand higher temperatures. Here, we investigated the wear behavior of candidate silicon carbide (SiC)-based composite claddings with different levels of surface finish in fretting against a commercial ZIRLO alloy grid using a unique bench-scale autoclave GTRF rig. The experiments mimicked the environment in an industrial full-assembly PWR simulator. Fretting tests were conducted with a realistic load (~0.5 N) in deionized water under a pressure of 20–23 bar at 204 °C for 100 h. While the SiC/SiC composite claddings showed significantly higher wear resistance than the commercial ZIRLO alloy cladding as expected, the smoother versions experienced surprisingly higher wear than the much softer counterface, ZIRLO grid. The wear mechanism of the SiC/SiC cladding was attributed to the SiC wear debris that was trapped at the fretting interface causing both 3-body and 2-body (embedded into the grid surface) abrasion of the cladding. Rougher SiC/SiC claddings had less material loss but caused more wear on the ZIRLO grid. Finally, pre-oxidized ZIRLO grid showed better compatibility with the SiC/SiC cladding to protect both the cladding and grid as a result of reduced wear debris trapping.

36 MATERIALS SCIENCE↗

Post weld heat treatment and operating temperature effect on tribological behavior of laser cladded stellite 21 coating

This study intends to investigate the feasibility of using laser cladding as a potential process to repair hot working tools by a hardfacing process. A Stellite 21 alloy coating was printed on a 350 maraging steel via laser cladding and the coating microstructure and tribological performance were characterized in as printed conditions and after heat treatment. Such a laser-processed coating showed a high integrity with little porosity and good bonding with the substrate. The Stellite coating produced substantially lower friction and a smoother contact area but had inferior wear resistance compared with the maraging steel substrate. Post process heat treatment at 650 °C for 20 h led to significant amount of strain-induced FCC to HCP phase transformation but had little improvement in wear resistance. Detailed materials characterization using X-ray diffraction and electron microscopy provided fundamental insights to the underlying mechanisms. This study opens the door for future R&D for tool surface repair by laser cladding.

36 MATERIALS SCIENCE↗

Progress Report on Graphite-Salt Interaction Studies (FY21)

This report summarizes the activities performed in FY21 to investigate the interactions between nuclear graphite and molten salts, such as FLiNaK. First, building on last year’s achievements, the team improved the procedure for measurements on pressurized salt intrusion in nuclear graphite and performed new experiments at variable pressures with specimens of different sizes and shapes. Additionally, the team actively provided suggestions and comments for ASTM D8091, Standard Guide for Impregnation of Graphite with Molten Salts , which came up for periodic revision in 2021. Second, the team expanded its capabilities to further characterize salt-impregnated graphite by procuring and installing a laser-induced breakdown spectroscopy (LIBS) instrument capable of producing a 3D chemical composition of a surface and subsurface region of specimens. A methodology for accurately analyzing information was developed, and a manuscript was submitted for publication. The LIBS instrument sample cell is sealed in controlled inert atmosphere, which is an advantage for using humidity-sensitive samples and Be-contaminated samples. This aligns with the team’s effort to expand the capabilities of handling FLiBe and Becontaining materials in two newly installed glovebox units. Third, the team performed preliminary tribology tests for pebble graphite wear in contact with stainless steel in dry state and in molten salt at high temperature. These tests are needed to establish the baseline for the wear of pebble graphite by friction against metallic walls. The friction and wear of pebbles in the fluoride salt-cooled hightemperature reactor are expected to generate dust, which is a concern for other components’ properties and safe reactor operation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Wear Mechanism Analysis of a New Rotary Shear Biomass Comminution System

A new biomass comminution system, Crumbler rotary shear, was developed to process fuel-grade biomass. The rotary shear is more efficient than the traditional hammer mill in comminuting high-moisture biomass and producing more uniform particles with minimal fines. However, the milling unit experiences significant wear in processing dirty woodchips. This study investigated the wear mechanisms of the rotary shear system based on analysis of the minerals carried by woodchips and characterization of actual worn components. Abrasive wear was found to be the dominant effect, and localized adhesive wear (material transfer), microfracture (chipping), and plastic deformation were additional effects. Connections have been made between the wear progression of key cutting components and the particle size change of biomass extrinsic minerals. On the basis of the wear mechanism understanding, mitigations based on advanced tool materials and optimized tool geometric designs are being developed for improving the tool life and cutting efficiency.

09 BIOMASS FUELS↗