Search NASA⌕ Search

Engineering topics

Qu, Jun

Publications and source records attributed to Qu, Jun.

At least 55 records · Page 3

Impact of Primary and Secondary ZDDP and Ionic Liquid as Lubricant Oil Additives on the Performance and Physicochemical Properties of Pd-Based Three-Way Catalysts

In the present study, two industry primary and secondary zinc dialkyldithiophosphate standards, ZDDP1 and ZDDP2, respectively, are evaluated for their impact on the performance of Pd-based three-way catalyst and bench-marked against two mixed lubricant additives formed from either ZDDP1 or ZDDP2 with a second-generation oil-miscible phosphoric-containing ionic liquid (IL). The three-way catalysts (TWCs) are exposed to the lubricant additives in an engine bench under four different scenarios: a base case with no additive (NA), ZDDP1, IL+ZDDP1, ZDDP2, and IL+ZDDP2. The engine-aged TWC samples are characterized through a variety of analytical techniques, including evaluation of catalyst reactivity in a bench-flow reactor. With respect to the water–gas shift reaction and the oxygen storage capacity, the ZDDP2- and IL+ZDDP2-aged TWC samples are more degraded than the ZDDP1- and IL+ZDDP1-aged TWC samples. X-ray diffraction (XRD) patterns indicate that phosphorus in the form of CePO4 was found to be present in the washcoat of all TWC samples, with the highest amount found in the ZDDP2-aged TWC sample. The results obtained from XRD are further confirmed by those from inductively coupled plasma-optical emission spectroscopy (ICP-OES), which show that more phosphorus is detected in the washcoat of ZDDP2- and IL+ZDDP2-aged TWC samples than in the ZDDP1- and IL+ZDDP1-aged TWC samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Using Ionic Liquid Additive to Enhance Lubricating Performance for Low-Viscosity Engine Oil

Energy efficient lubricants are essential for sustainable transportation, and the trend is to develop and implement lower viscosity lubricants with more effective additives. Ionic liquids (ILs) have been reported as candidate additives with superior friction and wear reducing capabilities. Unlike most literature relying on bench-scale testing of simple oil–IL blends, this study produced low-viscosity (SAE 0W-12) fully formulated engine oils using a phosphonium-organophosphate IL as an antiwear additive and evaluated them in both bench-scale tribological testing and full-scale fired engine dynamometer testing. The experimental formulation containing a combination of ZDDP and IL outperformed the formulations using either ZDDP or IL alone, as well as a commercial SAE 0W-20 engine oil in terms of mitigating boundary friction, wear, and contact fatigue-induced micropitting. Furthermore, racing engine dynamometer tests demonstrated 3–4 °C lower oil temperature, 4–5 ft-lbs higher horsepower output, and up to 9.9% better fuel economy for the IL-containing SAE 0W-12 experimental oil compared with selected commercial SAE 5W-30 and 0W-20 engine oils.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Corrosion and Chemical Characterization of Bio-Oils from Biomass with Varying Ash and Moisture Contents

As part of the Feedstock Conversion Interface Consortium four samples of pine chips (all combinations of low and high moisture and ash content) were collected and processed for fast pyrolysis. The prepared biomass samples were liquefied at the National Renewable Energy Laboratory (NREL) using the fast pyrolysis process. Following some characterization of the bio-oils at NREL, the bio-oils were shipped to Oak Ridge National Laboratory (ORNL) for corrosion testing and further characterization.The content and composition of ash in each bio-oil was determined. Corrosion testing consisted of exposing selected metallic and elastomer samples for 1000 hr at 50°C and for longer times at room temperature as well as electrochemical impedance spectroscopy measurements to assess relative corrosivity of the bio-oils. Chemical characterization was conducted to identify the corrosive component of the bio-oils as well as to define the chemical differences among the oils. It was hypothesized that there could be a catalytic effect from the higher ash content in two of the biomass sources. Results of these characterization and corrosion studies will be reported.

Keiser, Jim↗

Wear penalty for steel rubbing against hard coatings in reactive lubricants due to tribochemical interactions

Hard coatings and surface adsorptive/reactive lubricants are two common strategies for improving wear protection, but what if they are used together? In this study, steel-steel and steel-coating sliding was investigated in boundary lubrication of polar and non-polar oils containing a ZDDP or an ionic liquid. Two hard coatings, diamond-like-carbon (DLC) and chromium nitride (CrN), were used. Furthermore, for a steel-steel contact, wear was effectively reduced by using a more surface reactive lubricant, as expected. However, the steel ball wear was increased against a hard coating and further worsened with a more polar oil and/or a more surface reactive additive. The wear mechanism is proposed as a combined effect of physicochemical interactions with the lubricant, mechanical polishing by the counterface, and material adhesion.

36 MATERIALS SCIENCE↗

Tribological behavior of ceramic-alloy bearing contacts in molten salt lubrication for concentrating solar power

Molten salts are considered as candidate heat transfer fluids and thermal energy storage media for next generation concentrating solar power (CSP). A molten salt circulates inside the piping and heat exchanger and also functions as a lubricant for the sleeve bearings of the CSP pump. Furthermore, wear- and corrosion-resistant high-temperature bearing materials are critical for the pump efficiency and durability. This study evaluated the tribological performance of candidate bearing materials in lubrication of a molten chloride salt mixture (20% NaCl + 40% MgCl 2 + 40% KCl) at 750 °C in an inert argon gas (a simulative CSP pump environment). Six ceramic-alloy pairs were tested, zirconia and silicon nitride against Haynes 244, Hastelloy C276, and Tribaloy T900 alloy, and ranked by the friction coefficient and wear loss. Characterization of worn surfaces suggested the wear mechanism as a combination of abrasion, adhesion, and tribocorrosion. Results from this study provide fundamental insight for the development and selection of bearing materials for molten salt powered CSP pumps.

14 SOLAR ENERGY↗

Effects of Particle Size and Concentration of Magnesium Oxide on the Lubricating Performance of a Chloride Molten Salt for Concentrating Solar Power

One engineering challenge for the next-generation concentrating solar power (CSP) is to identify appropriate heat transfer and thermal energy storage media. A chloride salt mixture (20 wt % NaCl + 40 wt % MgCl 2 + 40 wt % KCl) in a molten phase is proposed as a potential fluid for carrying the heat as well as lubricating the CSP pump bearings. Due to the hygroscopic nature of MgCl 2 , the presence of magnesium oxide (MgO) particles is inevitable. In order to understand the impact of MgO particles, this study investigated the tribological behavior of the molten chloride salt mixture containing MgO of various particle sizes and concentrations. Tests were conducted at 750 °C in a dry Ar environment using a zirconia ball sliding against a Haynes 244 alloy disc lubricated by the molten salt. There was a clear trend of the increased friction coefficient and wear loss for a larger particle size and/or a higher concentration of MgO. Distinct wear mechanisms were identified for the ceramic ball and alloy disc. Results provide fundamental insights for this new research avenue of molten salt lubrication for CSP.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Why does a phosphonium-phosphinate ionic liquid protect the contact surfaces from wear and micropitting but increase vibration when used as an additive in rolling-sliding lubrication?

A phosphonium-phosphinate ionic liquid (IL) was studied as a lubricant additive for rolling-sliding contacts. The bench-scale test was designed to simulate automotive rear axle operation during cold start, highway towing, and overload conditions. Adding such an IL (2%) into a base oil significantly reduced wear loss and rolling contact fatigue, e.g., microcracking and micropitting, but made the vibrational noise notably higher under a low (-1.5%) sliding roll ratio (SRR). Additionally, worn surface characterization revealed an interesting texture pattern with alternating smoother plateaus and rougher valleys, which is believed to cause the high vibration. No increased vibration was observed at a high (-30%) SRR, possibly because the more aggressive sliding abrasion prevented such a surface texture from forming.

36 MATERIALS SCIENCE↗

Surface-modified and oven-dried microfibrillated cellulose reinforced biocomposites: Cellulose network enabled high performance

Microfibrillated cellulose (MFC) is widely used as a reinforcement filler for biocomposites due to its unique properties. However, the challenge of drying MFC and the incompatibility between nanocellulose and polymer matrix still limits the mechanical performance of MFC-reinforced biocomposites. In this study, we used a water-based transesterification reaction to functionalize MFC and explored the capability of oven-dried MFC as a reinforcement filler for polylactic acid (PLA). Remarkably, this oven-dried, vinyl laurate–modified MFC improved the tensile strength by 38 % and Young’s modulus by 71 % compared with neat PLA. Our results suggested improved compatibility and dispersion of the fibrils in PLA after modification. This study demonstrated that scalable water-based surface modification and subsequent straightforward oven drying could be a facile method for effectively drying cellulose nanomaterials. We find that the method helps significantly disperse fibrils in polymers and enhances the mechanical properties of microfibrillar cellulose-reinforced biocomposites.

36 MATERIALS SCIENCE↗

Autoclave grid-to-rod fretting wear evaluation of a candidate cladding coating for accident-tolerant fuel

In pressurized water reactors (PWRs), water flow induced vibrations cause contact and rubbing between the fuel rods and the supporting grid, a phenomenon known as Grid-to-Rod-Fretting (GTRF). GTRF may produce progressive wear damage on the fuel claddings leading to subsequent leakage of radioactive fission products. Various accident-tolerant fuel (ATF) concepts are being developed for higher resistance to the high temperature steam and one approach is to apply a cladding coating. Here, fretting wear behavior of a candidate Cr-coating was investigated using a unique bench-scale autoclave testing rig mimicking the environment in an industrial full-assembly PWR simulator. The contact was under a realistically low load (~0.5 N) lubricated by deionized water at a temperature of 204 °C under a pressure of 20-23 bars. Results demonstrated that the Cr-coating significantly improved the cladding's wear resistance when tested against a commercial ZIRLO grid with or without pre-oxidization. In addition, the Cr-coating also reduced wear on the non-oxidized ZIRLO grid but slightly increased the wear on the pre-oxidized grid.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Oil miscible phosphonium-phosphate ionic liquid as novel antiwear and antipitting additive for low-viscosity rear axle lubricants

Here we explored the feasibility of using a phosphonium phosphate ionic liquid as a candidate anti-wear and anti-pitting additive for rear axle lubricant. This particular IL was first added to a VHVI8 base oil at 2–3% concentration and demonstrated effective surface protection for wear and micro-cracking under rolling-sliding contacts. The promising results directed to a step further to produce a series of IL-containing low-viscosity (about a half of SAE 75W-90) fully formulated gear oils. Selected IL-containing experimental oils showed superior mitigation of rolling contact fatigue to a commercial SAE 75W-90 gear oil in bench-scale rolling-sliding tests. Full-scale hub dynamometer tests were then conducted and demonstrated more than 3% power output and torque generation for an IL-containing low-viscosity gear oil benchmarked against commercial baselines.

36 MATERIALS SCIENCE↗

Development of Ionic Liquid-Additized, GF-5/6 Compatible Low-Viscosity Oils for Automotive Engine and Rear Axle Lubrication for 4% Improved Fuel Economy

This joint project among ORNL, GM, and DRO successfully developed ionic liquid-additized low viscosity lubricants, SAE 0W-12 and 70W-80, for both IC engine and rear axle lubrication, respectively, and demonstrated combined vehicle fuel economy improvement (FEI). Phosphonium-alkylphosphate ILs have been found to be the most effective among the candidates in protecting surface damage from both sliding wear and rolling contact fatigue, and optimal IL concentrations have been determined. The IL’s impact on three-way catalyst seems to be significantly less adverse than the conventional ZDDP. Oil formulations were optimized for both energy efficiency and wear protection. Tribological bench testing of the IL-additized low-viscosity oils showed at least 40% lower boundary friction, more than 60% lower elastohydrodynamic friction, and greater than 50% less wear compared with commercial baselines. IL-additized lubricants have demonstrated FEI by 9.9% in engine dynamometer tests under extreme conditions and 6.9% increased power output in gear rig tests. Prototype IL-additized engine oil and rear axle fluid exhibited combined FEI of 1.39% and 3.24% benchmarked against the state-of-the-art baselines in vehicle testing of fresh oils under the Federal Test Procedure (FTP) city cycle and Highway Fuel Economy Driving Schedule (HWFET), respectively. Used oil analysis suggested that the IL-additized low-viscosity oils produced less wear than the commercial baselines. The gained fundamental understanding and demonstrated FEI in this work pave the way for future development and implementation of the ionic liquid technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Competitive Adsorption of Lubricant Base Oil and Ionic Liquid Additives at Air/Liquid and Solid/Liquid Interfaces

Oil-soluble ionic liquids (ILs) have been proved as effective additives in lubricant oils through tribological experiments and post-test analytical analyses. Here, surface structures of lubricant base oil, oil-soluble ILs, and their mixtures at the air/liquid and solid/liquid interfaces have been studied using sum frequency generation (SFG) vibrational spectroscopy. At the air/base oil and air/IL interfaces, the alkyl chains of the studied compounds were shown to be conformationally disordered and their terminal methyl groups point outward at the liquid surface. The base oil dominates the air/(base oil + IL) interface due to its higher surface excess propensity and larger bulk concentration. At the solid (silica) surface, ILs adopt a structure with their charged headgroups in contact with the silica surface, while their alkyl chains are more conformationally ordered or packed compared to the air/IL interface. At the interface between silica and (base oil + IL) mixtures, ILs also preferentially adsorb to the silica surface with their layer structures somewhat different from those of ILs alone. These results showed that ILs can adsorb onto the solid surface even before tribological contacts are made. The insights obtained from this SFG study provide a better understanding of the role of ionic liquids in lubrication.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Advanced Engine and Fuel Technologies Annual Progress Report (FY2019)

On behalf of the Vehicle Technologies Office of the U.S. Department of Energy, we are pleased to introduce the Fiscal Year (FY) 2019 Annual Progress Report for the Advanced Engine and Fuel Technologies Program. In support of the Vehicle Technology Office’s goal for future U.S. economic growth, the Program focuses on early-stage research and development to improve understanding of combustion processes, fuel properties, and emissions control technologies, generating knowledge and insight necessary for industry to cost-effectively develop the next generation of engines and fuels. One of the most promising and cost-effective approaches to improving the fuel economy of the U.S. vehicle fleet is to introduce the next generation of higher-efficiency, very-low-emission combustion engines that meet future federal emissions regulations into the passenger and commercial vehicle markets. Advanced fuel formulations that can incorporate non-petroleum-based blending agents could further enhance engine efficiency, reduce greenhouse gas emissions, and provide fuel diversification. Also, innovations in combustion, fuels, emissions control, air control, turbomachinery, and energy recovery could potentially increase fuel economy considerably compared to today’s vehicles. The expected national economic, environmental, and energy security benefits from these next-generation engines and fuels would be significant inasmuch as the majority of vehicles sold over the next several decades will still include an engine. The Program has set the following goals for passenger and commercial vehicle fuel economy improvements. By 2030, increase light-duty engine efficiency to demonstrate 35% improvement in passenger vehicle fuel economy (25% improvement from engine efficiency and 10% from fuel co-optimization) relative to a 2015 baseline vehicle, while meeting the U.S. Environmental Protection Agency Tier 3 Emission and Fuel Standards. By 2030, improve heavy-duty engine efficiency by 35% relative to a 2009 baseline vehicle and identify cost-effective high-performance fuels that can further increase efficiency up to an additional 4%, while meeting prevailing U.S. Environmental Protection Agency emissions standards. The Program utilized advanced combustion processes to increase engine efficiency, resulting in a modeled passenger vehicle fuel economy improvement of 19.4% (over a Model Year 2015 baseline) in FY 2019. This report highlights progress achieved by the Advanced Engine and Fuel Technologies Program during FY 2019. The nature, current focus, and recent progress of the Program are described together with summaries of National Laboratory, industry, and university projects that provide an overview of the exciting work being conducted to address critical technical barriers and challenges to commercializing the next generation of higher-efficiency engine, emissions control, and fuel technologies for passenger and commercial vehicles.

33 ADVANCED PROPULSION SYSTEMS↗

Cryo-quenched Fe–Ni–Cr alloy decorative steel single crystals II: Alloy phases, structure, hardness, tensile, tribological, magnetic and electronic properties

We have previously reported (Boatner et al., J. Alloys Compd. 691 (2017) 666–671) on the discovery, formation, processing, and application of a new decorative ternary steel alloy and on its use in a wide range of practical applications including: custom and commercial knives, art objects, jewelry, electronics, and furniture. This decorative property results when polished single crystals of the 70 wt%Fe-15 wt%Ni-15 wt% Cr austenitic alloy are cryo-quenched into the martensitic phase resulting in the formation of a three-dimensional raised pattern of mixed austenitic/martensitic laths. These laths propagate across large dimensions of the material due to the absence of grain boundaries in the single crystal. The macroscopic optically reflective 3-D decorative pattern reproduces the structural symmetry inherent in the single-crystal orientation. This pattern results solely from the metallurgical phase properties of the ternary alloy and is completely distinct from the properties of Damascus steels or more modern so-called pattern-welded steels. Here we use X-ray diffraction, nanoindentation, hardness measurements/scratch testing, tribological measurements, and alloy resistivity and magnetization methods to obtain a more fundamental and comprehensive study of the effects of the austenitic/martensitic phase transition on the structural and physical properties of the 70 wt%Fe-15 wt%Ni-15 wt% Cr alloy. These results reveal new insight into irreversible phenomena that are associated with the inhibited phase transition on heating of the two-phase, mixed austenitic/martensitic structure that is formed subsequent to cryo-quenching the alloy crystal to 77 K.

36 MATERIALS SCIENCE↗

Ultralow Boundary Lubrication Friction by Three-Way Synergistic Interactions among Ionic Liquid, Friction Modifier, and Dispersant

Interactions among antiwear additives (AWs), friction modifiers (FMs), and dispersant in a lubricating oil are critical for tribological performance. This study investigates compatibilities of three oil-soluble ionic liquids (ILs, candidate AWs) with an FM, molybdenum dithiocarbamate (MoDTC), and a dispersant, polyisobutene succinimide (PIBSI) under boundary lubrication. Either synergistic or antagonistic effects were observed depending on the IL’s chemistry. Adding an aprotic phosphonium–alkylphosphate or phosphonium–alkylphosphinate IL into the oil containing MoDTC and PIBSI had detrimental impact on the friction and wear behavior. PIBSI was found to preferably interact/react with the aprotic IL to lose its ability of suspending MoDTC and to partially consume or even deplete the IL. In contrast, a protic ammonium–alkylphosphate IL seemed to be able to coexist with PIBSI and work synergistically with MoDTC, yielding a sustainable, ultralow boundary friction. A three-stage tribochemical process is proposed to explain how this IL + MoDTC pair interacts with the contact surface to form a chemically reacted, wear-protective tribofilm supporting a physically adsorbed, friction-reducing film on top. We report this study provides fundamental insights of the compatibilities among three common lubricant components, antiwear, friction modifier, and dispersant, which can be used to guide future lubricant development.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Material Characterization-Based Wear Mechanism Investigation for Biomass Hammer Mills

Biomass, as harvested, is composed of inorganic compounds both intrinsically and extrinsically and can be abrasive. The present study investigates the wear modes and mechanisms of two types of blades of hammer mills used in biomass size reduction (impacting the particle size and distribution) and densification (impacting the size, shape, and density). The dominant wear modes for the stage 1 steel blades are determined to be erosive and polishing wear. For the stage 2 blades with a carbide weld overlay, the main wear mechanisms are erosion and fracture. Partial replacement of Co by Fe in the outer layer of the carbide grits, likely induced by diffusion during high-temperature welding, has been correlated to the observed microcracking. Finally, the microcracking is believed to weaken the grit strength and fracture toughness to make the overlay prone to fracture and erosion due to repetitive contact with the inorganic contents in chopping biomass.

42 ENGINEERING↗

Material-Dependent Antagonistic Effects between Soot and ZDDP

While soot in engine oil is known to accelerate the wear of diesel and gasoline direct-injection compression-ignition engines, there is a lack of consensus on the wear mechanism though various hypotheses have been proposed in the literature. Particularly, some recently observed antagonistic effects between soot and a common lubricant antiwear additive, zinc dialkyldithiophosphate (ZDDP), while others did not. The discrepancy is, in part, explained by the strong alloy dependence of such antagonism discovered in this study. Specifically, four alloys, 52100 steel and M2, M50, and A2 tool steels, are tested in lubricants containing carbon black (CB, a soot surrogate) with and without ZDDP present. Adding the CB alone to the oil increases the wear rate for all steel alloys as expected. However, distinct wear performance is observed for the four steel alloys when ZDDP is introduced to the CB-containing oil: while the 52100 steel has notable wear reduction, the three tool steels suffer significant wear increase. Comprehensive tribofilm characterization suggests that the Mo content in the steel alloy and the sulfur from ZDDP strongly influence wear behavior. The combination of CB/Mo-catalyzed sulfidation and CB-accelerated abrasion is hypothesized to be responsible for the high wear of the Mo-alloyed tool steels.

36 MATERIALS SCIENCE↗

Composition-Preserving Extraction and Characterization of Biomass Extrinsic and Intrinsic Inorganic Compounds

The inorganic content of biomass impairs size reduction tool life and the conversion process. Conventional ash extraction relies on furnace combustion that inevitably alters the inorganic compounds due to oxidation and decomposition. This study developed composition-preserving methods for extracting and analyzing extrinsic and intrinsic inorganic compounds. Comprehensive characterization was carried out on selected biomass feedstocks, including corn stover, pine residue, and pine anatomical fractions, to reveal their inorganic species and morphology. The extrinsic inorganic compounds were found to be dominated by quartz, along with other minor minerals, such as albite, microcline, and gehlenite, and have particle sizes ranging from tens to hundreds of micrometers. Among the pine anatomical fractions, the needles contain the highest intrinsic silicon content while the bark trapped the most extrinsic minerals. By correlation of the total ash and extrinsic inorganic contents to the wear behavior, both the extrinsic and intrinsic inorganic compounds were concluded to have made significant contributions to the wear process. Finally, the results here validated a new approach to characterize inorganic compounds in biomass and provided fundamental insights for their potential impact on preprocessing tool wear.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗