Search NASA⌕ Search

Engineering topics

Qu, Jun

Publications and source records attributed to Qu, Jun.

At least 73 records · Page 4

Understanding the Impact of Lignocellulosic Biomass Variability on the Size Reduction Process: A Review

The importance of size reduction to the commercial deployment of biomass utilization technologies cannot be overemphasized. Size reduction is necessary to create good flowing, easily digestible lignocellulosic biomass. However, inefficiencies and inconsistencies have not been well addressed for the process of size reduction. This has motivated quite a few research studies, some of which have reported the influence of process variables and pretreatment on the size reduction performance as well as the development of novel size reduction equipment and empirical mathematical models. In this Perspective, we present a systematic and critical evaluation of the state of lignocellulosic biomass size reduction research to provide insights for engineers and scientists for future development and investigation. We first briefly discuss the structural biology and failure mode of lignocellulosic biomass. Then, we present a comprehensive, data-driven picture of the interactions among lignocellulosic biomass attributes, size reduction process variables, pretreatment processes, and size reduction process performance (as defined by product characteristics and size reduction energy consumption). The sizing equipment tool wear issues are also summarized. Finally, we highlight some existing gaps and future research opportunities for lignocellulosic biomass size reduction to inform the development of newer technologies that could effectively produce high-value lignocellulosic biomass particles.

09 BIOMASS FUELS↗

Ionic liquids containing symmetric quaternary phosphonium cations and phosphorus-containing anions, and their use as lubricant additives

An ionic liquid composition having the following generic structural formula: wherein R1, R2, R3, and R4 are equivalent and selected from hydrocarbon groups containing at least three carbon atoms, and X− is a phosphorus-containing anion, particularly an organophosphate, organophosphonate, or organophosphinate anion, or a thio-substituted analog thereof containing hydrocarbon groups with at least three carbon atoms. Also described are lubricant compositions comprising the above ionic liquid and a base oil, wherein the ionic liquid is dissolved in the base oil. Further described are methods for applying the ionic liquid or lubricant composition onto a mechanical device for which lubrication is beneficial, with resulting improvement in friction reduction, wear rate, and/or corrosion inhibition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Impact of Lubricant Oil Additives on the Performance of Pd-Based Three-Way Catalysts

As alternative lubricant anti-wear additives are sought to reduce friction and improve overall fuel economy, it is important that these additives are also compatible with current emissions control catalysts. In the present work, a second-generation oil-miscible phosphorous-containing ionic liquid (IL), is evaluated for its impact on Pd-based three-way catalyst (TWC) reactivity and benchmarked against the industry standard zinc dialkyl-dithio-phosphate (ZDDP). The TWCs are exposed to the lubricant additives in an engine bench under four different scenarios: base case with no additive (NA), ZDDP-only, IL-only, and IL + ZDDP. The engine-aged TWC samples, along with the as-received TWC, are characterized through various analytical techniques including catalyst reactivity evaluation in a bench-flow reactor. The temperature of 50% conversion (T 50 ) for the ZDDP-aged TWC increases by 11, 21, and 36 °C for CO, C 3 H 6 , and C 3 H 8 , respectively, as compared with the no-additive case. Similarly, the T50 for IL-only and IL + ZDDP-aged TWCs also increase as compared with the no-additive case. Even though the water-gas-shift (WGS) reactivity is similar for all engine-aged samples, the IL-aged TWC had higher oxygen storage capacity than the ZDDP-aged TWC. EPMA analysis reveals penetration of phosphorus deep into the washcoat for all engine-aged TWCs. Results from XRD indicate the presence of CePO 4 and AlPO 4 on the washcoat of IL, ZDDP, and IL + ZDDP-aged TWC samples but not on the fresh and NA TWC samples. Additionally, ICP-OES results show a large amount of phosphorus in the washcoat of IL, ZDDP and IL + ZDDP-aged TWC samples and a lesser amount in NA TWC samples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

New Functionality of Ionic Liquids as Lubricant Additives: Mitigating Rolling Contact Fatigue

Oil-soluble ionic liquids (ILs) have recently been demonstrated as effective lubricant additives of friction reduction and wear protection for sliding contacts. However, their functionality in mitigating rolling contact fatigue (RCF) is little known. Because of the distinct surface damage modes, different types of surface protective additives often are used in lubricants for sliding and rolling contacts. Therefore, the lubricating characteristics and mechanisms of ILs learned in sliding contacts from the earlier work may not be translatable to rolling contacts. This study explores the feasibility of using phosphonium-phosphate, ammonium-phosphate, and phosphonium-carboxylate ILs as candidate additives in rolling–sliding boundary lubrication, and results suggested that an IL could be either beneficial or detrimental on RCF depending on its chemistry. Particularly, the best-performing phosphonium-phosphate IL at 2% addition made a low-viscosity base oil significantly outperform a more viscous commercial gear oil in reducing the RCF surface damage and associated vibration noise. This IL generated a thicker, smoother, and more homogeneous tribofilm compared with commercial additives, which is likely responsible for the superior RCF protection. Results here suggest good potential for using appropriate IL additives to allow the use of low-viscosity gear and axle fluids for improved efficiency and durability.

36 MATERIALS SCIENCE↗

Synergistic Interactions Between Silver and Palladium Nanoparticles in Lubrication

The reactivity and functionality of nanoparticles (NPs) are determined by the material- and size-dependent physicochemical properties at nanoscale. While single-type metallic NPs have been extensively studied for many potential applications, combination of multitype NPs and the interactions among them have received less attention. Here, an interesting synergistic effect between silver and palladium NPs is presented for using them together as lubricant additives. Dodecanethiol-modified Ag and Pd NPs were discovered to interact actively in a solution, changing their sizes, shapes, and electronic structures. A mixture of these two NPs was able to form a stable suspension in a lubricating oil and effectively improve tribological performance in the concentration range of 0.1–1 wt %. The Ag–Pd NP blend further reduced the friction and wear by >30% and >80%, respectively, compared with either NP alone at the same total NP concentration. The NPs and worn surfaces were characterized using a set of comprehensive analytical tools and the superior lubricating behavior was attributed to the formation of two types of protective tribofilms on the contact surfaces.

36 MATERIALS SCIENCE↗

Is more always better? Tribofilm evolution and tribological behavior impacted by the concentration of ZDDP, ionic liquid, and ZDDP-Ionic liquid combination

Anti-wear additives (AWs), like zinc dialkyldithiophosphates (ZDDPs), have been used in lubricants for more than a half-century, and more effective candidate AWs, like oil-soluble ionic liquids (ILs), are emerging. However, there is a lack of fundamental understanding of how the AW concentration impacts the tribochemical activities at the contact interface. This study systematically investigated the friction and wear behavior in correlation to the tribofilm morphology and composition as a function of the concentration of a ZDDP, a phosphonium-alkylphosphate IL, and an IL+ZDDP combination. The ZDDP concentration rising from 0.4 to 6.4 wt% caused a proportionally increased friction coefficient, which was well correlated to a thicker, rougher, and more brittle tribofilm. This was further understood by the decreasing phosphates but increasing sulfur compounds in the ZDDP tribofilm. In contrast, the IL and IL+ZDDP maintained a low and stable friction coefficient at 0.5 wt% or above. There was no sulfur in the IL tribofilm, and the sulfur compounds were maintained at a low level in the tribofilm for IL+ZDDP even at high concentrations. Results suggested minimizing the sulfur content in the tribofilm would be an effective way to control the friction. An interesting V-shape relationship between the AW concentration and the wear loss was observed for both the IL-containing AWs, with an optimum at 2 wt% for the IL alone and 0.46–0.92 wt% for the IL+ZDDP, respectively. A unique heat map was created using the phosphorus binding energy distribution to reveal the phosphate polymerization at different depths of the tribofilms, which provided additional insight for the tribofilm evolution.

36 MATERIALS SCIENCE↗

Wear and Why? How Ash Elements Can Help Define Wear Profiles of Biomass Feedstocks

Biomass feedstocks have been shown to cause high wear rates on biomass processing equipment, including grinders, pneumatic conveyance systems, and screw feeders. Previously, wear rates were positively correlated with ash concentrations. Physical and chemical properties, including ash content, vary across the anatomy of plants in biomass feedstocks. To better understand biomass tissues that cause the most wear, anatomical fractions of pine forest residues were tested for wear properties. Fractions were tested in the Accelerated Wear Testing Apparatus using steel coupon mass loss to evaluate wear rates. Extrinsic ash was extracted and characterized. Total ash content of the forest residue was 0.80wt%. Anatomical fractions showed varied amounts of ash with highest concentrations in bark and needles (2.33wt%, 3.52wt%, respectively). The wear rate of the forest residue was 2.36mg loss per kg biomass. Low ash fractions, including whitewood and cambium, caused little wear. Bark had lower ash than the needles but resulted in more wear (8.63 vs 5.57mg loss per kg biomass). Bark contained the most extrinsic ash and largest ash particle size, while needles contained the least extrinsic ash and smallest ash particle size. These findings indicate that total ash content (intrinsic plus extrinsic), soil contamination, and elemental analysis can provide information related to wear properties of biomass materials; however, these analyses do not fully explain the differences observed in the wear rates of bark and needles. Additional testing is to determine other parameters of importance.

Lacey, Jeffrey A.↗

Ionic liquids as oil additives for lubricating oxygen-diffusion case-hardened titanium

This study attempts to use ionic liquids (ILs) as oil additives to lubricate oxygen-diffusion (OD) case-hardened titanium for improved friction and wear behavior. Four oil-soluble ILs were used as additives in a base oil for boundary lubrication of an OD-treated Ti-6Al-4V surface sliding against a bearing steel ball. The ILs improved the friction behavior to various extents and the two phosphate ILs clearly outperformed the conventional ZDDP. Unlike ZDDP that adversely caused a higher material loss, ILs exhibited excellent wear protection suggesting good material-chemical compatibility. Particularly, the carboxylate IL protected the OD-Ti surface from any measurable wear. As a result, the morphology and chemical composition of the worn surfaces and tribofilms were examined to gain insights of the anti-wear mechanism.

36 MATERIALS SCIENCE↗

Shape-preserving machining produces gradient nanolaminate medium entropy alloys with high strain hardening capability

A high density of grain boundaries can potentially increase structural materials' strength, but at the expense of losing the materials' strain hardening ability at high flow stress levels. However, endowing materials with grain size gradients and a high density of internal interfaces can simultaneously increase the strength and strain hardening ability. This applies particularly for through-thickness gradients of nanoscale interface structures. In this work, we apply a machining method that produces metals with nanoscale interface gradients. Conventional bulk plastic deformation such as rolling, a process applied annually to about 2 billion tons of material, aims to reduce the metal thickness. We have modified this process by introducing severe strain path changes, realized by leading the sheet through a U-turn while preserving its shape, an approach known as ‘hard turning’. Furthermore, we applied this process at both room temperature and 77 K to a NiCrCo medium entropy alloy. Micropillar compression was conducted to evaluate the mechanical response. After hard turning at room temperature, the surface microstructure obtained a ~50% increase in yield stress (0.9 GPa) over the original state with homogeneous grain size (0.4 GPa), but the initial strain hardening rate did not show significant improvement. However, after hard turning at 77 k, the gradient nanolaminate structure tripled in yield stress and more than doubled its initial strain hardening rate. The improvements were achieved by introducing a specific microstructure that consists of gradient nanolaminates in the form of nanospaced twins and martensite in the face center cubic (fcc) phase. This microstructure was formed only at cryogenic temperature. It was found after turning at room temperature that only nanospaced twins were present in the fcc phase inside nanolaminates that had formed at the surface. The origin of the enhanced strain hardening mechanism was studied. Joint density functional theory (DFT) and axial next nearest neighbor Ising (ANNNI) models were used to explain the temperature-dependent phase formation of the NiCrCo nanolaminate at the surface of the hard-turned material.

36 MATERIALS SCIENCE↗

HIGH-STRENGTH LIGHTWEIGHT ENGINES FOR HEAVY-DUTY DIESEL TRUCKS

This project with Cummins supports the development of next generation heavy duty diesel engines that can achieve a 50% or better Break Thermal Efficiency (BTE). The fuel efficiency roadmap for the 50% BTE engine considers six main areas for efficiency improvement in the baseline engine, several of which involve making more efficient use of thermal energy (heat) in the engine. Increased operating temperatures and improved thermal management are expected to enable significant increases in $power$ $density$, thus resulting in greater power output for the same sized engine or engine downsizing (or light weighting) for the same power output. However, it has become apparent that several key components will be exposed to temperatures beyond the capabilities of current engine and exhaust materials, requiring the availability of the next generation of high temperature materials to allow the engine to reach the targeted efficiencies, commercially viable durability, and emission targets. The objective of this project was to identify and/or develop key materials, and evaluate their critical properties to enable the design and development of a lightweight, higher efficiency engine, with enhanced temperature capability and reduced heat-loss to the atmosphere in order to facilitate waste heat recovery and improved efficiency. An increase in the temperature capability of exhaust manifold materials, and piston materials were identified as having a positive influence on the efficiency of the next generation diesel engines. Since the current materials (High SiMo cast irons used in exhaust manifolds, and 4140 steel in pistons) are already operating near their limits of their temperature and strength capabilities, it was determined that new materials with the right combination of properties are required for these components. Oxidation and constrained thermal fatigue tests were used to down-select CF8C plus (CF8CP), a cast austenitic stainless steel, for exhaust manifolds capable of operating at higher temperatures. A prototype exhaust manifold was fabricated using CF8CP and successfully tested in a marine engine. A functionally graded multiple-layer thermal barrier coating system was designed with four layers of mixed bondcoat alloy (NiCoCrAlYHfSi) and yttria stabilized zirconia (YSZ) and was shown to reduce the effective thermal conductivity of the coating-substrate (steel and Ti-6Al-4V) system. The graded alloy and YSZ mixture were intended to achieve better match of thermal expansion coefficient (CTE) and minimize thermal stresses. Such coatings can increase the temperature capability of pistons fabricated from steel and Ti-alloys. Effect of oil additives and friction conformal contact friction tests showed there was a 15-30% reduction in friction by the polymer-graphite composite coating compared to the uncoated steel piston. Standalone Mn-P coating had little beneficial impact. Changing the oil from CJ-4 to PC-11 had little impact on the friction behavior in boundary lubrication. Wear behavior was tested under a point contact configuration with a high contact pressure. The candidate CK-4 oil showed similar or slightly better lubricity compared to the CJ-4 oil while the candidate FA-4 oil decisively increased the piston skirt wear. Although both coatings prevented scuffing failure observed for the uncoated steel skirt in a base oil without an additive package, they surprisingly caused a higher piston wear rate when tested in any of the fully formulated engine oil. The detrimental impact was attributed to the Mn-P film, either as a standalone coating, or a coating interlayer. The porous and brittle Mn-P film was broken during the wear test and the released hard Mn-P grains are suspected to cause third-body abrasion to accelerate the wear process. This work also evaluated the feasibility of developing an improved high temperature, low mass, cost-neutral turbocharger compressor wheel for heavy-duty engine applications from TiAl using additive manufacturing, utilizing its unique ability to fabricate high strength, low weight structures. This work has shown that the phase transforming nature of the TiAl alloys enable obtaining equiaxed microstructures in the as-built state without the need for tedious beam parameter manipulations. The HIPed structures have good RT tensile properties that will enable them to be surface machined to the required tolerance that can 2 then be heat treated to obtain the desired microstructures. Additionally, the negligible residual stresses stemming from the high build chamber temperatures ensure the parts are formed without cracks (one of the major issues in traditional manufacturing of these intermetallics).

33 ADVANCED PROPULSION SYSTEMS↗

Palladium Nanoparticle-Enabled Ultrathick Tribofilm with Unique Composition

There is a consensus that savings of 1.0–1.4% of a country’s gross domestic product may be achieved through lubrication R&D. Recent studies have shown great potential for using surface-functionalized nanoparticles (NPs) as lubricant additives to enhance lubricating performance. NPs were reported with ability of producing a low-friction antiwear tribofilm, usually 20–200 nm in thickness, on the contact surface. In contrast, this study reports an unexpected 10 times thicker (2–3 μm) tribofilm formed by dodecanethiol-modified palladium NPs (core size: 2–4 nm) in boundary lubrication of a steel–cast iron contact. Adding 0.5–1.0 wt % such NPs to a lubricating oil resulted in significant reductions in friction and wear by up to 40 and 97%, respectively. Further investigation suggested that the PdNP core primarily was responsible for the improvement in both friction and wear, whereas the thiolate ligand only contributed to the wear protection but had little impact on the friction behavior. In addition, unlike most previously reported tribofilms that contain a substantial amount of metal oxides, this PdNP-induced tribofilm is clearly dominated by Pd/S compounds, as revealed by nanostructural examination and chemical analysis. Finally, such a ultrathick tribofilm with unique composition is believed to be responsible for the superior lubricating behavior.

36 MATERIALS SCIENCE↗

Compatibility between Various Ionic Liquids and an Organic Friction Modifier as Lubricant Additives

Tribological performance of a boundary lubrication contact is largely dominated by the friction modifier (FM) and antiwear (AW) additives in the lubricant. While oil-soluble ionic liquids (ILs) have recently demonstrated promising AW functionality, their compatibility with FMs is little known and even less understood for nonferrous alloys. Here in this paper, we report the latest results for several selected ILs when used together with an organic FM (OFM) in lubricating a steel–bronze contact. Depending on the IL chemistry, either synergistic or antagonistic effects were observed. The three aprotic ILs ([P 8888 ][DEHP], [P 66614 ][BTMPP], and [P 66614 ][C 17 H 35 COO]) seemed to degrade the OFM’s lubricating performance. In contrast, the protic IL [N 888 H][DEHP] exhibited a strong synergistic effect with the OFM, yielding an ultralow steady-state friction coefficient (0.02) and a low wear rate (<10 –8 mm 3 /(N m)), which significantly outperformed the IL or the OFM alone. Surface characterization found no chemically reacted tribofilm on the bronze worn surface. On the other hand, a unique physically adsorbed surface film as a result of interconnection between the IL and OFM molecules by hydrogen bonds is proposed on the basis of chemical analysis. Such an adsorption surface film is expected to be difficult to compress vertically but easy to shear horizontally, leading to low friction and wear.

36 MATERIALS SCIENCE↗

U.S. Department of Energy Fuels & Lubricants Project on Lubricant Technology - Innovation, Discovery, Design, and Engineering (Final Report)

In 2016, the Vehicle Technologies Office (VTO) of the Department of Energy (DOE) issued a solicitation for the AOP Lab Call research in FY2017 on a number of topics related to vehicles. Topic 6A of the Lab Call focused on research related to advanced lubricants: '...(in) support of the lubricants program goal to, by 2020, demonstrate novel formulations for powertrain and driveline lubricants, compatible with new and legacy vehicles, to achieve at least a 4 percent real-world fuel economy improvement.' Argonne National Laboratory (ANL) in collaboration with Oak Ridge National Laboratory (ORNL) and Pacific Northwest National Laboratory (PNNL) was awarded a 3-year multilab project on 'Lubricant Technology - Innovation, Discovery, Design, and Engineering.' Research on the project began in FY2017 at the three laboratories with industry participation; however, in FY2018, the project was terminated due to budgetary constraints. The following is the final report for the project and highlights progress made during the first year of research. The report is divided into sections that highlight the following: goals, objectives, milestones and deliverables; project highlights; outreach - publications, conferences, and reports; milestones accomplished; research progress.

30 DIRECT ENERGY CONVERSION↗

Investigating grid-to-rod fretting wear of nuclear fuel claddings using a unique autoclave fretting rig

Fuel rods in a pressurized water nuclear reactor (PWR) experience coolant flow-induced relative motion against the grid support features, a phenomenon called grid-to-rod fretting (GTRF), which may cause progressive fretting wear damage. Wear-through of the cladding on fuel rods will leak the radioactive fuel into the coolant loop to significantly increase the radiation level in PWR primary loop and often trigger expensive Post Irradiation Examination. In this work, a unique autoclave fretting test rig was designed and fabricated to allow studying GTRF using actual cladding and grid materials. Water temperature was up to 220 °C, which was designed to mimic the environment in an industry full-assembly reactor core simulator. The contact load (0.1–1 N), oscillation frequency (20–30 Hz) and stroke (50–150 µm), and work rate (1–3 mW) were defined based on simulations of GTRF in an actual reactor. Using this autoclave GTRF rig, tests were conducted to learn the effect of water temperature and to investigate the wear behavior of different cladding-grid material combinations currently used in actual PWRs, including Zr alloy claddings without and with pre-oxidation against Zr alloy and Inconel grids. Higher water temperature evidently increased the cladding wear, and pre-oxidation of the Zr alloy and/or using the Inconel grid effectively reduced the wear rate. In conclusion, results were correlated with the data of a full-size industry reactor core simulator in terms of both wear rate and wear scar morphology.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Benchscale Evaluation of Nanodiamond Oil Additives

This CRADA between Cool-X and ORNL was to investigate the impact of diamond nanoparticles as diesel engine oil additives on lubricating behavior and gain fundamental understanding of the friction and wear reduction mechanisms. Systematic tribological bench tests were used for evaluating the Cool-X diamond nanoparticles (ND) as candidate diesel engine oil additives, and surface characterization was carried out to reveal the friction reduction mechanisms. No significant micro-rolling effect or increased oil pressure-viscosity coefficient was observed. Instead, a faster running-in and moderate friction reduction were achieved by the ND in tests of used diesel engine components, which was attributed to the polishing effect. ND agglomeration seemed to a problem and could significantly impair the functionality and future research is needed to seek the mitigation.

33 ADVANCED PROPULSION SYSTEMS↗

Ionic liquids containing symmetric quaternary phosphonium cations and phosphorus-containing anions, and their use as lubricant additives

An ionic liquid composition having the following generic structural formula: ##STR00001## wherein R 1 , R 2 , R 3 , and R 4 are equivalent and selected from hydrocarbon groups containing at least three carbon atoms, and X - is a phosphorus-containing anion, particularly an organophosphate, organophosphonate, or organophosphinate anion, or a thio-substituted analog thereof containing hydrocarbon groups with at least three carbon atoms. Also described are lubricant compositions comprising the above ionic liquid and a base oil, wherein the ionic liquid is dissolved in the base oil. Further described are methods for applying the ionic liquid or lubricant composition onto a mechanical device for which lubrication is beneficial, with resulting improvement in friction reduction, wear rate, and/or corrosion inhibition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Improved Lubricating Performance by Combining Oil-Soluble Hairy Silica Nanoparticles and an Ionic Liquid as an Additive for a Synthetic Base Oil

This article reports on improved lubricating performance by combining oil-soluble poly(lauryl methacrylate) brush-grafted silica nanoparticles (hairy NPs or HNP) and an oil-miscible phosphonium-phosphate ionic liquid (IL) as a friction-reducing additive for a polyalphaolefin (PAO) oil. The HNP was synthesized by surface-initiated reversible addition–fragmentation chain transfer polymerization. At a total concentration of 2% and sufficiently high individual concentrations for HNP and IL in PAO, high-contact stress, ball-on-flat reciprocating tribological tests showed that the friction decreased by up to 23% compared with 2% HNP alone in PAO and by up to 35% compared to the PAO mixed with 2% IL. Scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy (XPS) analysis revealed that the tribofilm formed from the PAO containing 1% HNP + 1% IL was enriched with both Si and P, indicating that both hairy NPs and IL were involved in the tribochemical reactions. In addition, the O 1s and Si 2p peaks in the core-level XPS spectra exhibited significant shifts for the mixture of 1% HNP + 1% IL compared to those for 2% HNP, suggesting the possible formation of new covalent bonds. These results indicated that HNP and IL reacted with each other and also with the metal substrate during the rubbing process, which likely strengthened the tribofilm and its bonding with the substrate and thus further improved the lubrication.

36 MATERIALS SCIENCE↗

Hybrid Ionic-Nano-Additives for Engine Lubrication to Improve Fuel Efficiency

We developed a new class of hybrid organic-inorganic/metallic nanoparticles (NPs) as additives for polyalphaolefin (PAO) for friction and wear reduction to improve engine energy efficiency. The hybrid additives were synthesized by using polymers, ionic liquid (IL)-containing polymers, organic ligands, or ILs to functionalize NPs. The tribological properties of these hybrid NPs or mixtures of NPs and ILs were studied by high contact stress ball-on-flat reciprocating sliding tests at 100°C. Significant reductions in friction and wear were achieved compared to PAO base oil. The lubrication mechanisms were elucidated by both experimental and simulation studies.

36 MATERIALS SCIENCE↗