Search NASA⌕ Search

Engineering topics

Qu, Jun

Publications and source records attributed to Qu, Jun.

At least 145 records · Page 8

Oil-Miscible and Non-Corrosive Phosphonium Ionic Liquids as Candidate Lubricant Additives

Ionic liquids (ILs) have been receiving considerable attention from the lubricants industry as potential friction and wear-reducing additives, but their solubility in oils is an issue. Unlike most ionic liquids that are insoluble in non-polar hydrocarbon oils, this study reports phosphonium-based ILs (PP-ILs) that are fully miscible with both mineral oil-based and synthetic lubricants. Both the cation and anion in quaternary structures, long alkyl chains, and capability of pairing the cation and the anion via a H-O bond are hypothesized to improve the compatibility between ions and neutral oil molecules. The measured viscosities of the oil-IL blends agree well with the Refutas equation that is for solutions containing multiple components. High thermal stability and non-corrosiveness were observed for the PP-ILs. Effective friction reduction and anti-wear functionality have been demonstrated in tribological tests when adding 5 wt% of a PP-IL into a base oil, suggesting potential applications for using the oil-miscible PP-ILs as lubricant additives.

36 MATERIALS SCIENCE↗

Anti-Wear Performance and Mechanism of an Oil-Miscible Ionic Liquid as a Lubricant Additive

An ionic liquid (IL) trihexyltetradecylphosphonium bis(2-ethylhexyl) phosphate has been investigated as a potential anti-wear lubricant additive. Unlike most other ILs that have very low solubility in non-polar fluids, this IL is fully miscible with various hydrocarbon oils. In addition, it is thermally stable up to 347 oC, showed no corrosive attack to cast iron in ambient environment, and has excellent wettability on solid surfaces (e.g., contact angle on cast iron <8o). Most importantly, this phosphonium-based IL has demonstrated effective anti-scuffing and anti-wear characteristics when blended with lubricating oils. For example, a 5 wt.% addition into a synthetic base oil eliminated the scuffing failure experienced by the neat oil and, as a result, reduced the friction coefficient by 60% and the wear rate by three orders of magnitude. A synergistic effect on wear protection was observed with the current anti-wear additive when added into a fully-formulated engine oil. Nanostructure examination and composition analysis revealed a tribo-boundary film and subsurface plastic deformation zone for the metallic surface lubricated by the IL-containing lubricants. This protective boundary film is believed to be responsible for the IL s anti-scuffing and anti-wear functionality.

36 MATERIALS SCIENCE↗

DIESEL FUEL LUBRICATION

The diesel fuel injector and pump systems contain many sliding interfaces that rely for lubrication upon the fuels. The combination of the poor fuel lubricity and extremely tight geometric clearance between the plunger and bore makes the diesel fuel injector vulnerable to scuffing damage that severely limits the engine life. In order to meet the upcoming stricter diesel emission regulations and higher engine efficiency requirements, further fuel refinements that will result in even lower fuel lubricity due to the removal of essential lubricating compounds, more stringent operation conditions, and tighter geometric clearances are needed. These are expected to increase the scuffing and wear vulnerability of the diesel fuel injection and pump systems. In this chapter, two approaches are discussed to address this issue: (1) increasing fuel lubricity by introducing effective lubricity additives or alternative fuels, such as biodiesel, and (2) improving the fuel injector scuffing-resistance by using advanced materials and/or surface engineering processes. The developing status of the fuel modification approach is reviewed to cover topics including fuel lubricity origins, lubricity improvers, alternative fuels, and standard fuel lubricity tests. The discussion of the materials approach is focused on the methodology development for detection of the onset of scuffing and evaluation of the material scuffing characteristics.

Qu, Jun↗

ULTRACOATINGS - Enabling Energy and Power Solutions in High Contact Stress Environments Through Next Generation Nanocoatings

This work was a portion of a larger DOE/ITP Grand Challenge project led by Eaton Corporation and which included Ames Lab, Borg Warner Morse, and Pratt and Whitney Rocketdyne. The current report summarizes work done under a CRADA between ORNL and Eaton. Tests of two types were performed at ORNL during the course of this work: (1) simulations of timing chain wear and friction under reciprocating conditions, and (2) pin-on-disk screening tests for bearings undergoing unidirectional sliding. The four materials supplied for evaluation in a timing chain link simulation were hardened type 440B stainless steel, nitrided type 440B stainless steel, VC-coated type 52100 bearing steel, and (ZrTi)B-coated type 52100 bearing steel. Reciprocating wear tests revealed that the VC coating was by far the most wear resistant. In friction, the nitrided stainless steel did slightly better than the other materials. The results will also be included in the overall project report by Eaton Corp.

coatings↗

Nanocoatings for High-Efficiency Industrial and Tooling Systems

This industry-driven project was the result of a successful response by Eaton Corporation to a DOE/ITP Program industry call. It consisted of three phases in which ORNL participated. In addition to Eaton Corporation and ORNL (CRADA), the project team included Ames Laboratory, who developed the underlying concept for aluminum-magnesium-boron based nanocomposite coatings, and Greenleaf, a small tooling manufacturer in western Pennsylvania. This report focuses on the portion of this work that was conducted by ORNL in a CRADA with Eaton Corporation. A comprehensive final report for the entire effort, which ended in September 2010, has been prepared by Eaton Corporation.

friction↗

Nanostructure and Composition of Tribo-Boundary Films Formed in Ionic Liquid Lubrication

Since the idea of using ionic liquids (ILs) as lubricants was raised in 2001, many studies have been conducted in this area and results have demonstrated superior lubricating performance for a variety of ionic liquids. It is widely believed that tribochemical reactions occur between the metal surface and the IL during the wear process to form a protective tribo-boundary film on the contact area that reduces friction and wear. However, the study of this critical boundary film has been limited to top surface two-dimensional topography examination and chemical analysis in the literature. A more comprehensive characterization is needed to help understand the film formation process and the lubricating mechanism. This study demonstrated a multi-technique three-dimensional approach to characterize the IL-formed boundary films, including top surface morphology examination, cross section nanostructure characterization, and layered chemical analysis. Characterization was carried out on both ferrous and aluminum surfaces lubricated by an ammonium IL. The focused-ion-beam (FIB) technique enabled TEM/EDS examination on the cross section of the boundary film to provide direct measurement of the film thickness, visualization of the nanostructure, and analysis of composition. In addition, composition-depth profiles were generated using XPS aided by ion-sputtering to reveal the composition change at different levels of the boundary film to investigate the film formation process.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Scuffing initiation in metals sliding against copper under non-lubricated conditions

Metallic components in sliding contact are sometimes subjected to high-loads with little or no lubrication. Such starved conditions can lead to a phenomenon called scuffing. Various definitions exist for this term, but in the present case, three criteria were used to signal its onset: changes in friction, vibrations, and noise, coupled with surface examination. On this basis, scuffing initiation was determined for seven technically pure metals (Al, Mo, Nb, Ta, Ti, W, Cu) and stainless steel, all rubbing against Cu. A flat-ended pin-on-disk test configuration was used with normal loads of 1-3 N, and with step-wise increases in sliding speed from 0.16 to 2.56 m/s. Al was only weakly resistant to scuffing, presumably due to its solubility in Cu, its high ductility and its relatively low elastic modulus. Niobium provided satisfactory sliding behavior at low speeds and loads, presumably due to protective oxides; however, it scuffed at higher loads when the oxide broke through. Stainless steel, Mo, and Ta had higher friction coefficients than Al and Nb, presumably because the relatively high strengths of the former prevented severe wear even when their oxide films failed. Like Al, Ti scuffs on Cu, probably because of its high relative solubility; however, Ti's higher elastic modulus resists the more severe forms of surface damage than does Al. Of all the materials slid against Cu, W displayed the least scuffing, even under maximum speed and load. Tungsten's negligible solubility in Cu may have reduced its adhesion, and W's high elastic modulus resisted shear-deformation, even at high frictional heating. Self-mated Cu couple scuffed when the speed was increased. The oxides on the Cu surface serve as solid lubricant avoiding scuffing at lower speeds.

36 MATERIALS SCIENCE↗

Aluminum nanocomposites having wear resistance better than stainless steel

Tribological behavior of alumina-particle-reinforced aluminum composites made by powder metallurgy process has been investigated. The nanocomposite containing 15 vol% of Al2O3 nanoparticles exhibits excellent wear resistance by showing significantly low wear rate and abrasive wear mode. The wear rate of the nanocomposite is even lower than stainless steel. We have also demonstrated that such excellent wear resistance only occurred in the composite reinforced with the high volume fraction of nanosized reinforcing particles. The results were discussed in terms of the microstructure of the nanocomposite.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

CHARACTERIZATION AND TRIBOLOGICAL EVALUATION OF 1-BENZYL-3-METHYLIMIDAZOLIUM BIS(TRIFLUOROMETHYLSULFONYL)IMIDE AS NEAT LUBRICANT AND OIL ADDITIVE

Selected physical and chemical properties and tribological data for a newly-developed, imidazolium-based ionic liquid (IL) are presented. The IL is soluble in the SAE 5W-30 oil up to a certain weight percentage, and is as a promising candidate for use in lubrication applications, either in its neat version or as an oil additive. Characterization of the IL included dynamic viscosity at different temperatures, corrosion effects on cast iron cylinder liners, and thermal stability analysis. The tribological performance was evaluated using a reciprocating ring-on-liner test arrangement. When used in neat version this IL demonstrated friction coefficient comparable to a fully formulated engine oil, and when used as an oil additive it produced less wear.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Lubricants or lubricant additives composed of ionic liquids containing ammonium cations

A lubricant or lubricant additive is an ionic liquid alkylammonium salt. The alkylammonium salt has the structure R.sub.xNH.sub.(4-x).sup.+,[F.sub.3C(CF.sub.2).sub.yS(O).sub.2].sub.2N.sup- .- where x is 1 to 3, R is independently C.sub.1 to C.sub.12 straight chain alkyl, branched chain alkyl, cycloalkyl, alkyl substituted cycloalkyl, cycloalkyl substituted alkyl, or, optionally, when x is greater than 1, two R groups comprise a cyclic structure including the nitrogen atom and 4 to 12 carbon atoms, and y is independently 0 to 11. The lubricant is effective for the lubrication of many surfaces including aluminum and ceramics surfaces.

Qu, Jun↗

Wear Analysis of Wind Turbine Gearbox Bearings

The objective of this effort was to investigate and characterize the nature of surface damage and wear to wind turbine gearbox bearings returned from service in the field. Bearings were supplied for examination by S. Butterfield and J. Johnson of the National Wind Technology Center (NREL), Boulder, Colorado. Studies consisted of visual examination, optical and electron microscopy, dimensional measurements of wear-induced macro-scale and micro-scale features, measurements of macro- and micro-scale hardness, 3D imaging of surface damage, studies of elemental distributions on fracture surfaces, and examinations of polished cross-sections of surfaces under various etched and non-etched conditions.

14 SOLAR ENERGY↗

Analysis of Wear Mechanisms in Low Friction, Nanocomposite AlMgB14-TiB2 Coatings

Recent developments in coating science and technology offer new opportunities to enhance the energy-efficiency and performance of industrial machinery such as hydraulic fluid pumps and motors. The lubricated friction and wear characteristics of two wear-resistant coatings, diamond-like carbon and a nanocomposite material based on AlMgB{sub 14}-50 vol.% TiB{sub 2}, were compared in pin-on-disk tribotests using Mobil DTE-24{trademark} oil as the lubricant. In each case, the pins were fixed 9.53 mm diameter spheres of AISI 52100 steel, the load was 10 N, and the speed 0.5 m/s in all tests. Average steady-state friction coefficient values of 0.10 and 0.08 were measured for the DLC and nanocomposite, respectively. The coatings and their 52100 steel counterfaces were analyzed after the tests by X-ray photoelectron and Auger spectroscopy for evidence of material transfer or tribo-chemical reactions. The low-friction behavior of the boride nanocomposite coating is due to the formation of lubricative boric acid, B(OH){sub 3}. In contrast, the low-friction behavior of the DLC coating is related to the relatively low dielectric constant of the oil-based lubricant, leading to desorption of surface hydrogen from the coating.

08 HYDROGEN↗