Search NASA⌕ Search

Engineering topics

Qu, Jun

Publications and source records attributed to Qu, Jun.

153 records · Page 9

NEUTRON DIFFRACTION MEASUREMENT OF RESIDUAL STRESSES IN FRICTION STIR PROCESSED NANOCOMPOSITE SURFACE LAYER

Friction stir processing (FSP) was successfully used to stir and mix nano-sized Al2O3 particles into a Al6061-T6 aluminum plate to form a nanocomposite layer up to 3 mm thick. This nanocomposite surface has demonstrated significantly improved surface hardness, yield strength, and wear-resistance without sacrificing the substrate ductility and conductivity. Neutron diffraction analysis was conducted to determine the residual stress distribution in the nanocomposite surface layer. For comparison, the residual stress of the aluminum surface that was processed similarly but had no particle involved was also measured. Results showed that the macro-level residual stresses in the FSP zone without particles are low due to the annealing effect induced by the long heating time and large heat input. The macro-level residual stresses in the FSP-processed Al-Al2O3 nanocomposite zone are tensile up to 100 MPa in all three directions. The details of the results will be further discussed in the paper.

36 MATERIALS SCIENCE↗

Ionic Liquids as Novel Lubricants and Additives for Diesel Engine Applications

The lubricating properties of two ionic liquids with the same anion but different cations, one ammonium IL [C8H17]3NH.Tf2N and one imidazolium IL C10mim.Tf2N, were evaluated both in neat form and as oil additives. Experiments were conducted using a standardized reciprocating sliding test using a segment of a Cr-plated diesel engine piston ring against a grey cast iron flat specimen with simulated honing marks as on the engine cylinder liner. The selected ionic liquids were benchmarked against conventional hydrocarbon oils. Substantial friction and wear reductions, up to 55% and 34%, respectively, were achieved for the neat ionic liquids compared to a fully-formulated 15W40 engine oil. Adding 5 vol% ILs into mineral oil has demonstrated significant improvement in the lubricity. One blend even outperformed the 15W40 engine oil with 9% lower friction and 34% less wear. Lubrication regime modeling, worn surface morphology examination, and surface chemical analysis were conducted to help understand the lubricating mechanisms for ionic liquids. Results suggest great potential for using ionic liquids as base lubricants or lubricant additives for diesel engine applications.

33 ADVANCED PROPULSION SYSTEMS↗

Oxygen Diffusion Enables Anti-Wear Boundary Film Formation on Titanium Surfaces in Zinc-Dialkyl-Dithiophosphate (ZDDP)-Containing Lubricants

This paper reports a wear reduction by up to six orders of magnitude for Ti-6Al-4V alloy when treated by an oxygen diffusion (OD) process and subsequently tested in a zinc-dialkyl-dithiophosphate (ZDDP)-containing lubricant. In addition to case hardening, it is discovered that OD enables the formation of an anti-wear boundary film on the titanium surface. Transmission electron microscopy and surface chemical analyses revealed that this boundary film has a two-layer structure comprising an amorphous oxide interlayer and a ZDDP-based top film with complex compounds.

36 MATERIALS SCIENCE↗

Use of Multiple Criteria to Map the High-Temperature Scuffing Behaviorof Co-Based Superalloys

The goal of thisworkwas to rank, as quantitatively as possible, the high-temperature scuffing characteristics of a series of Co-based materials, including coatings, for possible use inwear-critical components like those in diesel engine exhaust systems and emission-controls. A cylinder pivoting on its side against a flat tilewas used as the testing geometry. All testswere performed at 600 C in air. The time-dependent torque response was recorded for each 60 min test to investigate trends in friction as surfaces roughened and debris deposits built up. Candidate materials included Stellite 6B, Pleuco 33 (a white cast iron), nitrided stainless steel Type 310, IDM 5399 (a high-silicon, molybdenum iron), and coatings of both Tribaloy T-400 and Stellite 3 on stainless steel. Measurements of the damaged areas on the scuffed tiles were used to calculate a specific normal load and plot it versus the roughness of the worn tiles to map experimental results in a way that indicated the severity of scuffing for each material combination. Data on the map were annotated to reflect visual observations of the extent of damage as well. Using this test method and the foregoing criteria, nitrided type 310 stainless steel against T-400 gave the best overall performance.

33 ADVANCED PROPULSION SYSTEMS↗

Tribological characteristics of aluminum alloys against steel lubricated by ammonium and imidazolium ionic liquids

Sliding friction and wear characteristics of aluminum alloys against AISI 52100 steel lubricated by ionic liquids (ILs) were investigated at both room and elevated temperatures. The tested aluminum alloys include a commercially pure aluminum Al 1100, a wrought alloy Al 6061-T6511, and a cast alloy Al 319-T6. The lubricating performance of two ILs with the same anion, one ammonium-based [C8H17]3NH.Tf2N and one imidazolium-based C10mim.Tf2N, were compared each other and benchmarked against that of a conventional fully-formulated engine oil. Significant friction (up to 35%) and wear (up to 55%) reductions were achieved by the ammonium IL when lubricating the three aluminum alloys compared to the engine oil. The imidazolium IL performed better than the oil but not as well as the ammonium IL for Al 1100 and 319 alloys. However, accelerated wear was unexpectedly observed for Al 6061 alloy when lubricated by C10mim.Tf2N. Surface chemical analyses implied complex tribochemical reactions between the aluminum surfaces and ILs during the wear testing, which has been demonstrated either beneficial by forming a protective boundary film or detrimental by causing severe tribo-corrosion. The effects of the IL cation structure, aluminum alloy composition, and tribo-testing condition on the friction and wear results have been discussed.

36 MATERIALS SCIENCE↗

Oxygen-Diffused Titanium as a Candidate Brake Rotor Material

Titanium alloys are one of several candidate materials for the next generation of truck disk brake rotors. Despite their advantages of lightweight relative to cast iron and good strength and corrosion resistance, titanium alloys are unlikely to be satisfactory brake rotor materials unless their friction and wear behavior can be significantly improved. In this study, a surface engineering process oxygen diffusion was applied to titanium rotors and has shown very encouraging results. The oxygen diffused Ti-6Al-4V (OD-Ti) was tested on a sub-scale brake tester against a flat block of commercial brake lining material and benchmarked against several other Ti-based materials, including untreated Ti-6Al-4V, ceramic particle-reinforced Ti composites (MMCs), and a thermal-spray-coated Ti alloy. With respect to friction, the OD-Ti outperformed all other candidate materials under the imposed test conditions with the friction coefficient remaining within a desirable range of 0.35-0.50, even under the harshest conditions when the disk surface temperature reached nearly 600 C. In addition, the OD-Ti showed significantly improved wear-resistance over the non-treated one and was even better than the Ti-based composite materials.

36 MATERIALS SCIENCE↗

FORMING Al-Al2O3 NANOCOMPOSITE SURFACES USING FRICTION STIR PROCESSING

This study presents a solid state surface engineering process to form a nanocomposite layer on aluminum surface. Friction stir processing (FSP) was used to stir and mix nano-sized Al2O3 particles into a commercially pure aluminum surface to form an Al-Al2O3 nanocomposite layer of up to several millimeters thick. Compared with a non-processed aluminum surface, a nanocomposite surface with 15 vol% nano-particles has demonstrated increased hardness (by 3X) and yield strength (by 10X), and reduced friction coefficient (by 55%) and wear rate (by 100X). Transmission electron microscopy (TEM) has revealed high matrix dislocation density in the nanocomposite surface that is believed to be largely responsible to such significant property improvements. Neutron diffraction measurements suggested tensile residual stress in the aluminum matrix. The stress was mainly induced by thermal-expansion-mismatch between aluminum and alumina.

36 MATERIALS SCIENCE↗

Wear of Spheroidal Graphite Cast Irons for Tractor Drive Train Components

The study was prompted by a desire to improve the wear resistance of power transmission components in rear axle drives on commercial farm tractors. Reciprocating wear tests were conducted under lubricated and non-lubricated conditions on three spheroidal cast irons which varied in strength and hardness (designated GGG450, GGG600, and GGG700). Hemispherically-tipped steel pins (designed 42CrMoS4/ 41CrS4) were used as the sliders. Except for the test duration, test procedures were similar to those described in ASTM Standard Test Method G133 for linearly-reciprocating sliding. Among the three cast irons tested, the harder and stronger the alloy, the lower was its wear rate. Wear factors were approximately four orders of magnitude lower for experiments lubricated in fresh, fully-formulated lubricating oil. There was a linear relationship between Brinell hardness of the alloys and the negative logarithm of the wear factors that were expressed in (mm3/N-m). Wear of lubricated test pins was not measurable due to the presence of deposits; however under non-lubricated sliding, the ratio of the wear of the flat specimen to that of the pin decreased as the hardness of the flat specimens approached that of the pin specimen.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Tribological studies of a Zr-based bulk metallic glass with different states

The tribological characteristics of a bulk-metallic glass (BMG) Zr52.5Cu17.9Ni14.6Al10.0Ti5.0 (Vit 105) with different states have been studied. Friction and wear tests were conducted using a ball-on-flat reciprocating sliding apparatus against AISI E52100 bearing steel under dry condition. The observed wear resistance in an ascending order is deformed, crept, relaxed, and as-cast. Results suggested that the wear process of BMG alloys involved abrasion, adhesion, and oxidation. The differences in hardness, free volume, and embrittlement at different states significantly affected the friction and wear behaviors of the BMG alloys.

36 MATERIALS SCIENCE↗