Search NASA⌕ Search

Engineering topics

Rand, J. L.

Publications and source records attributed to Rand, J. L..

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Biaxial Stress Limit for ULDB Film

The current ULDB design applies stress to the shell film biaxially to control creep in the latitudinal direction. The recent change in design paradigm, from a uniaxial to biaxial stress state basis, arose from a new perspective that the biaxial loading can control strain in both principal surface dimensions as discussed below. The current ULDB project path was thus enabled by a more thorough understanding of the nonlinear viscoelastic properties of the shell film material, linear low-density polyethylene (LLDPE). Although a very similar material is also used in NASA zero-pressure (ZPB) and long-duration balloons (LDB), the different stress state requires a new approach to shell material qualification.

Sterling, W. J.↗
NASA NTRS2004

A Constitutive Equation for Stratospheric Balloon Materials

The selection of a suitable material for use as a reliable stratospheric balloon gas barrier and structural component is based on a variety of properties. Due to a more desirable combination of properties, the low density polyethylene that has been used for the last half century has been replaced during the last decade by linear low density polyethylene (LLDPE). This paper describes the effort to characterize the time dependent properties of a 38 micron coextrusion of LLDPE. The nonlinear viscoelastic constitutive equation presented may be used to accurately describe the creep and/or relaxation of this film when subjected to a biaxial state of stress, such as might be required for an extended balloon flight. Recent laboratory data have been used to mod@ an existing model of LLDPE to account for differences caused by the coextrusion process. The new model will facilitate structural design optimization and reliability assessment, and may be further utilized as a predictive tool to benefit in-flight operations. Current structural analysis tech&ques based on linear elastic properties have predicted stresses in excess of those which would actually exist.

Rand, J. L.↗
NASA NTRS1985

Thin film strain transducer

A strain transducer system and process for making same is disclosed wherein a beryllium-copper ring having four strain gages disposed thereon is electrically connected in Wheatstone bridge fashion to output instrumentation. Tabs are bonded to a balloon or like surface with strain on the surface causing bending of the ring and providing an electrical signal through the gages proportional to the surface strain. A figure is provided which illustrates a pattern of a one-half ring segment as placed on a sheet of beryllium-copper for chem-mill etch formation, prior to bending and welding of a pair of the segments to form a ring structure.

Rand, J. L.↗
NASA NTRS1984

Thin film strain transducer

A strain transducer system and process for making the same is disclosed. A beryllium copper ring having four strain gages is electrically connected in Wheatstone bridge fashion to the output instrumentation. Tabs are bonded to a balloon or like surface with strain on the surface causing bending of a ring which provides an electrical signal through the gages proportional to the surface strain. A photographic pattern of a one half ring segment as placed on a sheet of beryllium copper for chem-mill etch formation is illustrated.

Rand, J. L.↗
NASA NTRS1983

Balloon film strain measurement

A discussion is presented of the results of a flight test program in which scientific research balloon material strain was measured in order to determine stress levels. Attention is given to material strain characteristics during the inflation, launch, ascent, and flight of a natural shape, zero-pressure scientific balloon. Measurements were conducted with a simple thin film strain transducer. Thermal, meridional and circumferential strain history data for the test flight are given.

Rand, J. L.↗
NASA NTRS1983

A thin film strain transducer

A device has been developed for the purpose of measuring longitudinal strain in thin polyethylene films. This paper describes the design, development, calibration, and application of this unique transducer in a variety of low temperature environments. This thin, ring-shaped device has a low effective modulus so as not to interfere with the strain that would naturally occur in a thin film. It has a standard 350 ohm impedance which is compatible with most available bridge balance, amplification, and telemetry instrumentation. This transducer has been successfully used for viscoelastic material characterization experiments in the laboratory, as well as in flight measurements of strain on the surface of scientific balloons during inflation, launch, ascent, and float.

Rand, J. L.↗
NASA NTRS1981

A balloon strain gage

This paper describes the development of a unique strain measuring device which is intended to monitor the state of strain in thin balloon films during flight. The gate is bonded directly to the film without significantly altering the state of strain or stress in the wall of the balloon. Results of a model balloon inflation are presented which indicate the gage to measure strain in a deployed balloon.

Rand, J. L.↗
NASA NTRS1981

Balloon material characterization

Experimental data are reviewed to study the state of stress and strain in a typical balloon fabricated from thin polyethylene film. Relaxation tests are conducted over a temperature range of -60 C to 140 C for a constant strain of 1%, and loads measured with the load cell are converted to values of the relaxation modulus. A log-log plot is made of the modulus as a function of time, and the maximum stress is found to occur at times of the order of one-half second. The film behaves as a nonlinear viscoelastic material, and by examining various theoretical relationships of stress and strain with temperature and time histories, a material testing program is developed which yields the necessary data to characterize the film.

Wilbeck, J. S.↗
NASA NTRS1981

Thin film strain transducer

Previous attempts to develop an appropriate sensor for measuring the stress or strain of high altitude balloons during flight are reviewed as well as the various conditions that must be met by such a device. The design, development and calibration of a transducer which promises to satisfy the necessary design constraints are described. The thin film strain transducer has a low effective modulus so as not to interfere with the strain that would naturally occur in the balloon. In addition, the transducer has a high sensitivity to longitudinal strain (7.216 mV/V/unit strain) which is constant for all temperature from room temperature to -80 C and all strains from 5 percent compression to 10 percent tensile strain. At the same time, the sensor is relatively insensitive (0.27 percent) to transverse forces. The device has a standard 350 ohm impedance which is compatible with available bridge balance, amplification and telemetry instrumentation now available for balloon flight. Recommendations are included for improved coatings to provide passive thermal control as well as model, tethered and full scale flight testing.

Rand, J. L.↗
NASA NTRS1979

Effects of soft foam insulation impact

High temperature reusable surface insulation (HTRSI) tiles were impacted by a variety of foam insulation materials typical of the debris expected to strike the shuttle orbiter during the initial phases of flight. Failure of the HIRSI coating was strongly dependent on the density and size of the projectile. The failure threshold was as low as 140 ft/sec for rubber and as high as 740 ft/sec for styrofoam. In addition, the impact pressure was measured for a variety of debris materials as a function of velocity.

Rand, J. L.↗
NASA NTRS1972

Optimization of a two stage light gas gun

Performance characteristics of the Texas A&M University light gas gun are presented along with a review of basic gun theory and popular prediction methods. A computer routine based on the simple isentropic compression method is discussed. Results from over 60 test shots are given which demonstrate an increase in gun muzzle velocity from 9.100 ft/sec. to 19,000 ft/sec. The data gathered indicated the Texas A&M light gas gun more closely resembles an isentropic compression gun rather than a shock compression gun.

Rynearson, R. J.↗
NASA NTRS1971

An analytical and experimental study of the behavior of semi-infinite metal targets under hypervelocity impact

The material strength and strain rate effects associated with the hypervelocity impact problem were considered. A yield criterion involving the second and third invariants of the stress deviator and a strain rate sensitive constitutive equation were developed. The part of total deformation which represents change in shape is attributable to the stress deviator. Constitutive equation is a means for analytically describing the mechanical response of a continuum under study. The accuracy of the yield criterion was verified utilizing the published two and three dimensional experimental data. The constants associated with the constitutive equation were determined from one dimensional quasistatic and dynamic experiments. Hypervelocity impact experiments were conducted on semi-infinite targets of 1100 aluminum, 6061 aluminum alloy, mild steel, and commercially pure lead using spherically shaped and normally incident pyrex projectiles.

Chakrapani, B.↗