Search NASA⌕ Search

Engineering topics

Reece, Charles

Publications and source records attributed to Reece, Charles.

61 records · Page 4

Energetic Condensation Growth of Nb Thin-Films for SRF Applications

AASC, JLab and NSU conduct research into SRF thin-film coatings by first characterizing properties such as morphology, grain size, crystalline structure, defects, and impurities, then measuring Tc and RRR, and following this with ?in-cavity? RF measurements of the Surface Impedance of the films at cryogenic temperatures. These progressive steps are essential to eventual design and measurement of SRF accelerator structures at high fields. We have recently produced Nb superconducting thin-films with crystal grain sizes ~50?m using our proprietary CED^TM cathodic arc technique. RRR of ~129 at Tc of 9.2K was measured in a film grown on a-plane sapphire heated to 400oC. At 20oC, the RRR dropped to ~4. Energetic condensation using cathodic arcs produces non-equilibrium fast ions (~50-100eV). These ion energies are much higher than typical sputtering energies. When such energetic condensation is complemented by substrate biasing (to ~200-300eV) the incident ion energy is further increased, allowing growth modes that would otherwise require much higher substrate temperatures. Data are presented for pure Nb films using SEM, EBSD, XRD and a Surface Impedance Characterization RF cavity.

Krishnan, Mahadevan↗

Analysis of the topographic transformation of Nb surface under controlled EP conditions

As the field requirements of niobium SRF cavities approach fundamental material limits, there is increased interest in understanding the details of topographical influences on realized performance limitations. In this study, a set of samples representing 24 different starting conditions used in cavity processing has been assembled. This set includes fine grain, large grain, and single crystal Nb samples under electron beam welding (EBW), hand grinding, and centrifugal barrel polishing (CBP) with a variety of stones, the latter provided by KEK colleagues. Sample topography has been carefully characterized in both the initial condition and after removal of 30 microns via well-controlled EP. A power spectral density (PSD) approach based on Fourier analysis of surface topography, stylus profilometry (SP) and atomic force microscopy (AFM) is used to distinguish the scale-dependent smoothing effects. The detailed topographic transformation of Nb surface with the varied starting state Nb surface is reported. This study will help to identify optimum EP parameter sets for controlled and reproducible surface levelling of Nb for cavity production. References: [1] ?Surface Roughness Characterization of Niobium Subjected to Incremental BCP and EP Processing Steps? , Hui Tian, G. Ribeill, Charles E. Reece, and Michael J. Kelley. Proceedings of 13th Workshop on RF Superconductivity, Beijing, China (Oct. 2007). This work was authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177

Tian, Hui↗

Energetic Condensation Growth of MgB2 Thin-Films for SRF Applications

We report single-step vacuum growth of a stoichiometric superconducting thin film of MgB2, using AASC?s cathodic arc deposition process. Energetic condensation using cathodic arcs produces non-equilibrium fast ions (~50-100eV) that allow growth modes on relatively low temperature substrates. We have demonstrated a film Tc of 34K with MgB2 by depositing at 275 °C in a single step, from a stoichiometric, solid MgB2 source. In a subsequent experiment, the single-step coated samples (on c-plane sapphire) were ex-situ annealed. Post-deposition anneal temperature ranged from 825?900K, for 15 minutes. The annealed film also showed a transition at 30K. An MgB2 film was also deposited over a 50mm diameter circle on a Buffered Chemically Polished Niobium substrate for future RF evaluation in a cavity. The depositions spanned a range of substrate temperatures from 550-675 K. The films began to change in appearance form silver to black as substrate temperature was increased, indicating a decreasing magnesium content in the films. Future plans are to reduce oxygen contamination and to use our filtered cathodic arc to deposit smoother films.

Krishnan, Mahadevan↗

X-ray Pole Figure Analysis on Fiber Textured Epitaxial Niobium Films for SRF Cavities

Single and large grain Nb films are of interest to reduce the cost of SRF cavities. The structural properties and SRF potential of Nb films obtained by coaxial energetic deposition (CEDTM) in an ultra-high vacuum process are compared and discussed. The CEDTM is a hybrid technique with both energetic ion deposition and implantation phases based on cathodic arc plasma sources, which are copious generators of condensable energetic (20-200 eV), multiply charged ions from metal or alloy cathodes. The X-ray pole figure of the thin films revealed grain orientations on Nb films grown at different substrate temperatures that indicate good structural and electrical properties. Single crystalline 110 epilayers of Nb films are grown on a-plane sapphire substrates at 400 degreeC, but at lower temperature, there are two kinds of twins in which the grains are rotated by ~45 degree about the film normal. RRR of ~129 and Tc=9.2K were measured on a Nb film on a-plane sapphire substrate at 400 degreeC, dropping to ~4 on a room temperature substrate.

Seo, Kang↗

Development of SIMS Standards for Measurement of H, C, O, N in Nb

Performance of SRF cavities is strongly dependent on the interior surface due to its shallow RF penetration depth. Therefore it is important to study Nb surface characteristics and identify elemental contamination which could affect the performance of the SRF Nb cavity. C, N, and O are of particular interest as interstitial contaminants and earlier work suggested very high H concentration [1]. Secondary Ion Mass Spectrometry (SIMS) has the depth resolution and sensitivity to quantitatively measure these species in the region of interest. However, standards for quantitative SIMS analysis of these elements in Nb did not exist. Initial attempts to develop an ion implanted standard were unsuccessful because of the roughness of the Nb surface and the inability to polish the soft metal Nb surface with traditional methods. In this study, Nb samples were specially chemical mechanical polished and then subsequently treated with a light buffered chemical polish (BCP). The result is a surface finish suitable for SIMS analysis and implantation standards. Ion implants of C, N, O, and deuterium (D) were obtained in Nb (and simultaneously in Si for dose verification). D was implanted to characterize H, and to avoid the high H background. The results show that D is apparently very mobile in Nb, and another approach will be required to quantify this element. This multi-element standard has already been of great benefit in characterization of C, O, and N in polycrystalline and large grain Nb [2]. [1] A. D. Batchelor, D. N. Leonard, P. E. Russell, F. A. Stevie, D. P. Griffis, G. R. Myneni, Proceedings of Single Crystal Niobium Technology Workshop, Brazil, AIP Conference Proceedings, Melville, NY (2007) 72-83. [2] P. Maheshwari, H. Tian, C. E. Reece, M. J. Kelley, D. P. Griffis, G. R. Myneni, F. A. Stevie, J. M. Rigsbee, A. D. Bachelor, Surface and Interface Analysis (in press) This work was authored by Jefferson Science Associates, LLC under U.S. DOE Contract No. DE-AC05-06OR23177

43 PARTICLE ACCELERATORS↗

HOM Survey of the First CEBAF Upgrade Style Cavity Pair

The planned upgrade of the Continuous Electron Beam Accelerator Facility (CEBAF) at the Thomas Jefferson National Accelerator Laboratory (JLab) requires ten new superconducting rf (SRF) cavity cryomodules to double the beam energy to the envisaged 12 GeV. Adequate cavity Higher Order Mode (HOM) suppression is essential to avoid multipass, multibunch beam break-up (BBU) instabilities of the recirculating beam. We report on detailed HOM surveys performed for the first two upgrade style cavities tested in a dedicated cavity pair cryomodule at 2K. The safety margin to the BBU threshold budget at 12 GeV has been assessed.

43 PARTICLE ACCELERATORS↗