Search NASA⌕ Search

Engineering topics

Repins, Ingrid

Publications and source records attributed to Repins, Ingrid.

43 records · Page 3

Comparative Study of the Defect Point Physics and Luminescence of the Kesterites Cu2ZnSnS4 and Cu2ZnSnSe4 and Chalcopyrite Cu(In,Ga)Se2: Preprint

In this contribution, we present a comparative study of the luminescence of the kesterites Cu2ZnSnS4 (CZTS) and Cu2ZnSnSe4 (CZTSe) and their related chalcopyrite Cu(In,Ga)Se2 (CIGSe). Luminescence spectroscopy suggests that the electronic properties of Zn-rich, Cu-poor kesterites (both CZTS and CZTSe) and Cu-poor CIGSe are dictated by fluctuations of the electrostatic and chemical potentials. Thelarge redshift in the luminescence of grain boundaries in CIGSe, associated with the formation of a neutral barrier is clearly observed in CZTSe, and, to some extent, in CZTS. Kesterites can therefore replicate the fundamental electronic properties of CIGSe.

14 SOLAR ENERGY↗

Correlations of Cu(In, Ga)Se2 Imaging with Device Performance, Defects, and Microstructural Properties

Camera imaging techniques have been used for the characterization of Cu(In,Ga)Se{sub 2} (CIGS) solar cells. Photoluminescence (PL) imaging shows brightness variations after the deposition of the CIGS layer that persist through CdS deposition and subsequent processing steps to finish the devices. PL and electroluminescence imaging on finished cells show a correlation to the devices corresponding efficiency and open-circuit voltage (V{sub OC}), and dark defect-related spots correspond to bright spots on images from illuminated lock-in thermography (LIT) and forward-bias dark LIT. These image-detected defect areas are weak diodes and shunts. Imaging provides locations of defects detrimental to solar cell performance. Some of these defects are analyzed in more detail by scanning electron microscopy using cross-sectional views.

14 SOLAR ENERGY↗

Co-Evaporated Cu2ZnSnSe4 Films and Devices

The use of vacuum co-evaporation to produce Cu2ZnSnSe4 photovoltaic devices with 9.15% total-area efficiency is described. These new results suggest that the early success of the atmospheric techniques for kesterite photovoltaics may be related to the ease with which one can control film composition and volatile phases, rather than a fundamental benefit of atmospheric conditions for film properties. The co-evaporation growth recipe is documented, as is the motivation for various features of the recipe. Characteristics of the resulting kesterite films and devices are shown in scanning electron micrographs, including photoluminescence, current-voltage, and quantum efficiency. Current-voltage curves demonstrate low series resistance without the light-dark cross-over seen in many devices in the literature. Band gap indicated by quantum efficiency and photoluminescence is roughly consistent with that expected from first principles calculation.

14 SOLAR ENERGY↗

Examination of Na-Doped Mo Sputtering for CIGS Devices (CRADA Final Report)

Na is an important ingredient in Cu(In,Ga)(Se,S) 2 (CIGS) photovoltaic devices, due to its ability to increase carrier density and passivate surfaces, grain boundaries, and Se vacancies. In the highest efficiency devices, Na is supplied to the growing CIGS film by diffusion through the Mo back contact from the sodalime glass substrate. This arrangement is problematic in that the Na content of the film is only indirectly controlled: deposition times, deposition temperatures, Mo morphology, and glass composition are coupled with the Na diffusion. Results in the literature show that the Mo, not the CIGS, is the primary barrier to Na diffusion. Alternatively, using a Na-free substrate or diffusion barrier, Na may be introduced by a NaF precursor deposited on top of the Mo. However, this forces a trade-off between carrier density and adhesion. If the NaF is not entirely consumed, the CIGS layer peels away from the Mo, encouraging the use of less NaF even though the best device properties tend to result from the thickest possible NaF layers. Furthermore, although early studies show that gross control of Na is sufficient to produce 12-14% small devices, the industry has reached this level and is ready to progress to higher performance. The sensitivity of NREL device efficiency (15 to 20%) to Mo morphology suggests that fine control of Na content is necessary for very high performance. This work has investigated the use of Na doped Mo (“MONA”) sputtering targets for use in preparing CIGS devices. The Mo:Na material is doped to about 3% Na by weight, implying that a 40 nm layer on top of the standard Mo contact validation of their product. contains sufficient Na to dope a 2.5 µm CIGS film. The ability to control Na doping independent of both CIGS processing conditions and adhesion is an important gain for industry and research. Manufacturers gain a route to increased manufacturability and performance, while NREL researchers gain a tightened performance distribution of devices and increased process flexibility. Our immediate partner in this work, the Climax Molybdenum Technology Center, gains validation of their product.

14 SOLAR ENERGY↗

Kesterites and Chalcopyrites: A Comparison of Close Cousins; Preprint

Chalcopyrite solar cells based on CuInSe2 and associated alloys have demonstrated high efficiencies, with current annual shipments in the hundreds of megawatts (MW) range and increasing. Largely due to concern over possible indium (In) scarcity, a related set of materials, the kesterites, which comprise Cu2ZnSnS4 and associated alloys, has received increasing attention. Similarities anddifferences between kesterites and chalcopyrites are discussed as drawn from theory, depositions, and materials characterization. In particular, we discuss predictions from density functional theory, results from vacuum co-evaporation, and characterization via x-ray diffraction, scanning electron microscopy, electron beam-induced current, quantum efficiency, secondary ion mass spectroscopy, andluminescence.

14 SOLAR ENERGY↗

Photovoltaic manufacturing: Present status, future prospects, and research needs

In May 2010 the United States National Science Foundation sponsored a two-day workshop to review the state-of-the-art and research challenges in photovoltaic (PV) manufacturing. This article summarizes the major conclusions and outcomes from this workshop, which was focused on identifying the science that needs to be done to help accelerate PV manufacturing. A significant portion of the article focuses on assessing the current status of and future opportunities in the major PV manufacturing technologies. These are solar cells based on crystalline silicon (c-Si), thin films of cadmium telluride (CdTe), thin films of copper indium gallium diselenide, and thin films of hydrogenated amorphous and nanocrystalline silicon. Current trends indicate that the cost per watt of c-Si and CdTe solar cells are being reduced to levels beyond the constraints commonly associated with these technologies. With a focus on TW/yr production capacity, the issue of material availability is discussed along with the emerging technologies of dye-sensitized solar cells and organic photovoltaics that are potentially less constrained by elemental abundance. Lastly, recommendations are made for research investment, with an emphasis on those areas that are expected to have cross-cutting impact.

14 SOLAR ENERGY↗