Search NASA⌕ Search

Engineering topics

Rockett, Angus

Publications and source records attributed to Rockett, Angus.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Stability of Cu(In x Ga 1− x )Se 2 Solar Cells Utilizing RbF Postdeposition Treatment under a Sulfur Atmosphere

Alkali halide postdeposition treatments (PDTs) have become a key tool to maximize efficiency in Cu(In x Ga 1− x )Se 2 (CIGS) photovoltaics. RbF PDTs have emerged as an alternative to the more common Na‐ and K‐based techniques. This study utilizes temperature‐dependent current–voltage ( JVT ) measurements to study a unique RbF PDT performed in a S atmosphere. The samples are measured before and after 6 months in a desiccator to study device stability. Both samples contain Na and K which diffuse from the soda–lime glass substrate. A reference sample and a RbF + S PDT sample both show the development of a rear contact barrier after aging. The contact barrier is higher for the RbF + S PDT sample, leading to decreased current in forward bias. Series resistance is also higher in the RbF + S PDT device which leads to lower fill factor. However, after aging the reference sample has a larger decrease in open‐circuit voltage ( V OC ). Ideality factor measurements suggest Shockley–Read–Hall recombination dominates both samples. V OC versus temperature and a temperature‐dependent activation energy model are used to calculate diode activation energies for each sample condition. Both techniques produce similar values that indicate recombination primarily occurs within the bulk absorber.

14 SOLAR ENERGY↗
DOE OSTI2023

Nonradiative Recombination Dominates Voltage Losses in Cu(In,Ga)Se 2 Solar Cells Fabricated using Different Methods

Voltage losses reduce the photovoltaic conversion efficiency of thin‐film solar cells and are a primary efficiency limitation in Cu(In,Ga)Se 2 . Herein, voltage loss analysis of Cu(In,Ga)Se 2 solar cells fabricated at three institutions with variation in process, bandgap, absorber structure, postdeposition treatment (PDT), and efficiency is presented. Nonradiative voltage losses due to Shockley–Read–Hall charge carrier recombination dominate and constitute >75% of the total compared to <25% from radiative voltage losses. The radiative voltage loss results from nonideal absorption and carriers in band tails that stem from local composition‐driven potential fluctuations. It is shown that significant bulk lifetime improvements are achieved for all alkali PDT processed absorbers, chiefly associated with reductions in nonradiative recombination. Primary voltage loss contributions (radiative and nonradiative) change little across fabrication processes, but variation in submechanisms (bulk lifetime, net acceptor concentration, and interface recombination) differentiate nonradiative loss pathways in this series of solar cells.

14 SOLAR ENERGY↗
DOE OSTI2023

Post-growth Recrystallization by Halides for High Throughput CIGS Photovoltaics

The objective of this project in broad terms was to address the capital equipment expense associated with Cu(In,Ga)Se 2 (CIGS) as a material for photovoltaic devices. This project has demonstrated a new method for processing CIGS using metal halides to recrystallize and enhance the quality of the final materials. A wide spectrum of metal halides were examined. Of these Cu and In chlorides and AgBr were found to be most effective; and, of these, AgBr was found to produce exemplary results. Cu and In chlorides were found to produce undesirable changes in film composition. The project demonstrated over 16% efficiency in a CIGS device deposited at 10x the standard rate of ~1 μm/hr and with a >100°C reduction in maximum temperature to 450°C. The entire deposition of the absorber layer including the recrystallization step required only 15 minutes, which is a 4x decrease in processing time.

14 SOLAR ENERGY↗
DOE OSTI2022

High-Rate and Low-Temperature Fabrication of Cu(In,Ga)Se 2 Solar Cells Using AgBr Induced Recrystallization

We present results demonstrating a three-stage, high-rate, low-temperature deposition process for Cu(In,Ga)Se 2 solar cells including a recrystallization step after the second stage, catalyzed by AgBr. The entire deposition and recrystallization process takes place below 450 °C in less than 15 min. Device results with efficiencies exceeding 16% are shown. Here, we achieve very high levels of grain growth and a greater than a 5% absolute increase in device performance because of the recrystallization step relative to an identical process not involving AgBr.

14 SOLAR ENERGY↗
DOE OSTI2022

Homogeneous CuGaSe 2 growth by the CuPRO process with In-Situ AgBr treatment

Homogeneous CuGaSe 2 thin film growth is limited by slow kinetics of formation. A modified growth process was previously developed to address this issue but requires two separate long, high temperature anneals. Here, we demonstrate that a short AgBr treatment can replace this modified growth process. The AgBr works as a transport agent to catalyze CuGaSe 2 formation and atomic mobility. Furthermore, this treatment results in large grains with homogeneous composition through the bulk. Solar cells made with this material show better performance.

14 SOLAR ENERGY↗
DOE OSTI2022

Evaluating Recombination Mechanisms in RbF Treated Cu(In${}_\mathrm{x}$Ga$_\mathrm{1-x}$)Se$_{2}$ Solar Cells

Rubidium fluoride (RbF) postdeposition treatment (PDT) has been shown to improve the performance of Cu(In x Ga 1-x )Se 2 (CIGS) photovoltaic devices. Here, in this study, temperature-dependent current voltage (JVT) and time-resolved photoluminescence (TRPL) experiments were combined with modeling using the solar cell capacitance simulator (SCAPS) computer code to investigate the effect of the RbF PDT. Two devices, one as-deposited and one with RbF PDT, were deposited by a three stage coevaporation process. JVT measurements suggest the dominant recombination mechanism may be tunneling-enhanced recombination via bandtail states, but that defect states in the bandgap can also be important. RbF PDT is shown to decrease the characteristic energy of the bandtails. TRPL data show an increase in the minority carrier lifetime after RbF PDT, leading to an improved open-circuit voltage. SCAPS modeling indicates that the dominant recombination mechanism is dependent on the specific defect makeup of a device, suggesting that small changes in processing conditions can impact device behavior. This explains the observation that, for some devices, defect states in the gap dominate while others, as is the case here, appear to be dominated by bandtails.

14 SOLAR ENERGY↗
DOE OSTI2022

A thermodynamic evaluation of metal halides for the recrystallization of Cu(In,Ga)Se 2

CdTe films are deposited at low temperatures and recrystallized to photovoltaic device quality using CdCl 2 treatments, leading to competitive manufacturing costs. Cu(In,Ga)Se 2 (CIGS) typically requires high-temperature, low-rate depositions to produce high-efficiency devices, resulting in higher costs. A similar metal halide treatment of CIGS has been demonstrated by us previously for some metal halide sources. To understand and optimize the process, a thermodynamic evaluation of candidate metal halides for such treatments is presented as a guide for their selection. By comparing bond dissociation energies, mono- and di-halide compounds are proposed to be ideal compounds to act as transport agents. Known recrystallization and temperature reduction benefits by Ag alloying suggests that Ag-halides should be used to aid transport of all species. The high vapor pressure and mobility of Ga compounds still poses a problem for metal halide treatment resulting in Ga etching and removal of intentional Ga gradients. Less severe but similar issues with In compounds may occur. As a result, Cu compounds have low vapor pressures which may limit transport, however, Cu is highly mobile in CIGS and recrystallization still occurs.

14 SOLAR ENERGY↗
DOE OSTI2022

Na Diffusion and Device Performance of AgBr Treated CuGaSe 2 Thin Films

Previous work demonstrated that uniform CuGaSe2 (CGS) thin films with large grains could be grown using a short AgBr vapor treatment during growth. Here, devices made with this treated CGS showed better performance compared to devices made with standard material. Here, it is shown that AgBr treated CGS device performance worsens over time and is attributed to the suppression of Na diffusion. A NaF post-deposition treatment is shown to effectively introduce Na into the AgBr treated CGS film and prevent device degradation.

14 SOLAR ENERGY↗
DOE OSTI2022

Grain Enhancement in Polycrystalline CuGaSe 2 by AgBr Vapor Treatment

Copper Gallium diselenide (CuGaSe 2 or CGS) thin film were deposited using a three-stage thermal co-evaporation process on molybdenum coated soda lime glass. Recrystallization was carried after the second stage by flashing AgBr for 2 mins. The change in morphology, structure and depth profile were studied after the treatment. SEM and XRD showed an increase in grain size and enhanced crystallinity. Here, a decrease in sodium profile after the treatment was observed through SIMS measurements. Overall, AgBr treatment of CGS seems to be promising for the improvement of film quality, which could help with enhanced device fabrication in the future.

14 SOLAR ENERGY↗
DOE OSTI2022

On the Effect of Indium Chloride Dose on the Recrystallization of Cu(In,Ga)Se 2 Thin Films and associated Devices

Cu(In,Ga)Se 2 thin films deposited by a single-stage co-evaporation process at 350 ºC on molybdenum coated soda lime glass substrate were annealed post-deposition in InCl 3 vapor. The amount of InCl 3 and Se was varied. Here, the annealing treatment was done at 450 ºC for 30 minutes. Increase in grain size was observed after the treatment in all cases by X-ray diffraction. Device performance was low, but improved slightly after KCN etching.

14 SOLAR ENERGY↗
DOE OSTI2022

Impact of Indium Chloride Treatment on the Properties of CuInSe 2 Thin Films

Copper Indium diselenide (CIS) semiconductor thin films were deposited by single-stage process. Following the deposition, annealing and recrystallization of CIS was carried out in the presence of InCl 3 at different temperatures. Increase in grain size was observed by SEM in all cases. Increase in peak intensity was observed by XRD after treatment, correlating well with the SEM results. Measurements of the composition by both XRF and EDS indicate significant changes, notably a decrease in copper content. Here, this will likely be an issue for device performance and will need to be addressed.

14 SOLAR ENERGY↗
DOE OSTI2022

Effect of Metal Halides Treatment on High Throughput Low Temperature CIGS Solar Cells

Copper indium gallium diselenide (CIGS) semiconductor thin films were deposited at high rate and low temperature using single-stage thermal co-evaporation process on molybdenum back contact. A post deposition treatment was done by flashing AgBr at 350 ºC to induce recrystallization. Changes in morphology were confirmed by SEM, with an observed increase in grain size, as well as by XRD measurements, with a decrease in FWHM. Device results show an improvement of the performance after the AgBr vapor treatment, as all the photovoltaic parameters enhanced. Altogether, AgBr seems to be a suitable transport agent and beneficial for device fabrication.

14 SOLAR ENERGY↗
DOE OSTI2022

Post-deposition Metal Halide Treatment of CuGaSe 2 for Photovoltaic Application

Copper gallium diselenide (CGS) semiconductor thin films were deposited by three-stage thermal co-evaporation process. Post-deposition treatments and recrystallization were performed at various AgBr doses of 40 mg, 60 mg, and 80 mg after the 2 nd stage. The changes in surface morphology were confirmed by SEM. The electrical properties were also modified, as the resistivity of the film decreases with increasing doses. Here, the device performance after the treatment did not change as expected, as the overall device performance only slightly increases in the case of 60 mg of AgBr. Substantial changes in the fabrication process will therefore be required for better device results.

14 SOLAR ENERGY↗
DOE OSTI2022

Large-Area (Ag,Cu)(In,Ga)Se 2 Thin-Film Solar Cells with Increased Bandgap and Reduced Voltage Losses Realized with Bulk Defect Reduction and Front-Grading of the Absorber Bandgap

The 1.24 eV bandgap, 18.8% power conversion efficiency Ag-alloyed chalcopyrite (Ag,Cu)(In,Ga)Se 2 (ACIGS) solar cells are characterized to relate voltage and efficiency improvements to electro-optical (EO) characteristics. Shockley-Read-Hall recombination center defect density, identified and characterized through deep level transient spectroscopy and time-resolved photoluminescence (TRPL), is reduced through potassium and copper treatment optimization. Concomitantly, longer minority carrier lifetimes are achieved, which increases open-circuit voltage (V OC ). Near-conduction band defects associated in earlier studies with light-induced current instability are also mitigated. Analysis of charge-carrier dynamics after single- and two-photon excitation is used to separate recombination at the front interface and in the absorber bulk. From TRPL decay simulations, the authors estimate ranges of key solar cell material characteristics: bulk carrier lifetime T bulk = 110-210 ns, charge-carrier mobility u = 110-160 cm 2 V -1 s -1 , and front interface recombination velocity S front = 700-1050 cm s -1 . This lowest-reported S front for ACIGS absorbers originates from the notched conduction band grading, which also makes the impact of the back interface recombination negligible. It is suggested in the results that solar cell performance enhancements can be made most readily with two distinct strategies: improving device architecture and reducing semiconductor defect densities. Using these approaches, power conversion efficiency in large-area solar cells is improved by 1.1% absolute.

14 SOLAR ENERGY↗
DOE OSTI2021

Computational design of passivants for CdTe grain boundaries

CdTe is the second most-widely deployed photovoltaic (PV) material due to its high efficiency and low manufacturing costs. Currently, polycrystalline CdTe (poly-CdTe) has a record efficiency of similar to 22%, which is still well below the theoretical limit (similar to 30%). Polycrystalline CdTe films that have incorporated Cl or Se show higher efficiency, possibly due to the segregation of these ions to the grain boundaries (GBs), where they may passivate the dangling bonds. However, the efficiency enhancement mechanisms of passivants in CdTe GBs, and the feasibility of employing alternative passivants, have not been well explored. Here, we present a systematic computational study of CdTe GBs with potential passivants, namely S, P, As, Se, and Sb on Te sites, and Na, Mg, Al, Sc, Cu, and Zn on Cd sites. Density functional theory (DFT) calculations were performed on GB dislocation core structures derived from scanning transmission electron microscopy (STEM) images of a model GB (bicrystal). We computed the segregation thermodynamics, electronic density of states, and charge variations near doped CdTe GBs. We find that segregation of impurities to GBs is thermodynamically favorable. For a Te-terminated core, Se, S, and P on Te sites effectively reduce midgap states. For both Cd-and Te-terminated dislocation cores, Sc and Al reduce midgap states when substituted for Cd atoms. Overall, the greatest improvement was achieved with co-doping, i.e. simultaneously substituting Te with Se and substituting Cd with Cu or Al. The elimination of midgap states is predicted to increase the photovoltaic efficiency of CdTe by reducing the recombination at grain boundaries.

14 SOLAR ENERGY↗
DOE OSTI2021

Study of Indium Chloride Vapor Treatment on Cu(In,Ga)Se 2 Semiconductor Thin Films

The recrystallization by indium chloride of Cu(In,Ga)Se 2 thin films deposited by co-evaporation at 350°C was studied. The process of recrystallization consists of the postdeposition treatment of CIGS sample by InCI3 vapor for 30 minutes with emphasis on grain growth. Here, the treatment resulted in uniform increased grain size and improved crystallinity. XRD measurements suggests the formation of indium rich phase. Dynamic SIMS were also performed to further understand the process, phase separation and the extent of gallium depletion.

14 SOLAR ENERGY↗