Phylogenetic tree of GAUT Protein Family and gene model, RNAi construct, and relative transcript abundance of GAUT4 in switchgrass, rice and poplar knockdown (KD) lines.

bio engineered↗

DOE OSTI2026

Glycosyl linkage analysis of fractionated cell walls from switchgrass WT and PvGAUT4-KD lines

bio engineered↗

DOE OSTI2026

Glycosyl linkage analysis of fractionated cell walls from P.deltoides WT and PdGAUT4-KD lines.

bio engineered↗

DOE OSTI2026

Higher_wood_density_lowers_feedstock_cost_and_has_minimal_impact_on_biomass_conversion_to_biofuels

Poplar and other woody feedstocks have the potential to provide up to 200 million tons of biomass per year that could be converted to liquid fuels. Most forestry strategies that aim at increasing biomass productivity per hectare rely on short rotation plantations of fast-growing varieties. The improvement of wood density as a key trait itself has largely been overlooked. We evaluated natural variation in wood density across a population of genetically diversePopulus trichocarpatrees grown in a common garden. Wood density varies greatly within this population but is heritable higher wood density was not systematically associated with reduced growth, challenging assumptions of a trade-off between wood density and biomass accumulation. Furthermore, denser wood led to significant improvements throughout the supply chain, including, lowering biomass production and transportation costs. Higher density not correlate to changes in biomass composition. Density did not impact bioconversion in the two feedstock-to-fuel pipelines tested (pretreatment by ionic liquids or soaking in aqueous ammonia, and fermentation to ethanol) on a representative subset of poplars. These findings highlight wood density as a promising breeding target for accelerating the development of high-yielding, conversion-efficient bioenergy crops and as an avenue for increasing land-use efficiency and reducing biomass transportation cost. This data set contain three datasets.

CBI↗

DOE OSTI2024

Elemental profiling and genome-wide association studies reveal genomic variants modulating ionomic composition in Populus trichocarpa leaves

The ionome represents elemental composition in plant tissues and can be an indicator of nutrient status as well as overall plant performance. Thus, identifying genetic determinants governing elemental uptake and storage is an important goal for breeding and engineering biomass feedstocks with improved performance. In this study, we coupled high-throughput ionome characterization of leaf tissues with high-resolution genome-wide association studies (GWAS) to uncover genetic loci that modulate ionomic composition in leaves of poplar ( Populus trichocarpa ). Significant agreement was observed across the three ionomic profiling platforms tested: inductively coupled plasma-mass spectrometry (ICP-MS), neutron activation analysis (NAA) and laser-induced breakdown spectroscopy (LIBS). Relative quantification of 20 elements using ICP-MS across a population of 584 genotypes, revealed larger variation in micro-nutrients and trace elements content than for macro-nutrients across genotypes. The GWAS performed using a set of high-density (>8.2 million) single nucleotide polymorphisms, identified over 600 loci significantly associated with variations in these mineral elements, pointing to numerous uncharacterized candidate genes. A significant enrichment for genes related to ion homeostasis and transport was observed, including several members of the cation-proton antiporters (CPA) family and MATE efflux transporters, previously reported to be critical for plant growth and fitness in other species. Our results also included a polymorphic copy of the high-affinity molybdenum transporter MOT1 found directly associated to molybdenum content. For the first time in a perennial plant, our results provide evidence of genetic control of mineral content in a model tree species.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

Studies of time resolution, light yield, and crosstalk using SiPM-on-tile calorimetry for the future Electron-Ion Collider

We recently proposed a high-granularity calorimeter insert for the Electron-Ion Collider (EIC) that is based on plastic scintillator tiles readout with silicon photomultipliers. In this work, we concretize its design by characterizing its building blocks with measurements of light yield, optical crosstalk, and timing resolutions using cosmic-rays, an LED, and a beta source. We also compared two approaches for the optical isolation of cells: "megatiles" with grooved boundaries between cells, and a 3D-printed plastic frame hosting individual cells. Further, we found that the latter suppresses optical crosstalk to negligible levels while providing an easier assembly method. Overall, these performance studies can help inform calorimeter design and realistic simulations of 5D showers (time, energy, position) for the EIC and other experiments.

47 OTHER INSTRUMENTATION↗

DOE OSTI2022

Relationships between Sphaerulina musiva Infection and the Populus Microbiome and Metabolome

Poplar ( Populus spp.) trees are ecologically and economically important trees throughout North America. However, many western North American poplar plantations are at risk due to the introduction of the nonnative fungal pathogen Sphaerulina musiva , which causes leaf spot and cankers, limiting their production.

16S rRNA↗

DOE OSTI2022

n-Butanol or isobutanol as a value-added fuel additive to inhibit microbial degradation of stored gasoline

Biofouling of gasoline can occur during fuel storage caused by bacteria and fungi that form a biofilm at a fuel/water interface and that produce organic acids and sulfides. Fuel additives are applied to gasoline to prevent biofouling but are relatively expensive, are not always effective against biofilms, and do not contribute to the combustibility of gasoline. Bio-isobutanol is an approved, certified advanced biofuel and is added up to 16% ( v/v ) in gasoline blends “iBut16”; n-butanol blends are currently under review. Microorganisms are inhibited by n-butanol or isobutanol when the aqueous concentration reaches >2-3% (w/ v ). We determined that n-butanol partitions into the aqueous phase of a model gasoline/water system reaching concentrations of 42 g/L and up to 48 g/L from gasoline blends at 10% and 24% ( v/v ), respectively. Likewise, isobutanol blended in gasoline at 10% and 24% ( v/v ) partitioned into an aqueous phase at 45 g/L and 53 g/L, respectively. Several bacterial and fungal strains that originate from fuel storage tanks, or are known to be solvent tolerant, were evaluated for their potential growth in a range of n- and isobutanol concentrations. Growth rates for all strains tested were reduced by 40–100% relative to untreated controls in n- and isobutanol concentrations of 1.5 and 2.0% ( v/v ). No observable growth occurred for any of the microorganisms in solvent concentrations at 3.0% ( v/v ). T amphiphilic and chaotropic properties of n- or isobutanol help them inhibit microbial growth and could serve as effective biocides during fuel storage as well as being valuable fuel additives.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2021

Stabilizing the Power System in 2035 and Beyond: Evolving from Grid-Following to Grid-Forming Distributed Inverter Controllers (Final Technical Report)

Under existing grid operations, large synchronous generators provide sufficient rotational inertia to form a rigid backbone for the bulk power system. With photovoltaics (PV) forecasted to provide more than 600 GW of generation by 2050 under the U.S. Department of Energy’s SunShot Initiative objectives, however, it is clear that power electronic inverters will play a dominant role in future systems, and low-inertia stability must be ensured to maintain system reliability. Today, the risks to system stability can be observed on geographically small islands, such as Hawaii, which contain a relatively large amount of installed PV. These risks stem from a fundamental shortcoming of contemporary control strategies—existing inverter controllers cannot guarantee grid stability. Given that future power systems driven by sustainable resources will be characterized by low inertia, locations such as Hawaii provide a glimpse into the obstacles facing future power systems. Considering these challenges, the aim of this project was to develop and demonstrate distributed inverter controllers that enable the reliable control of low-inertia power systems with hundreds of gigawatts of integrated PV.

14 SOLAR ENERGY↗

DOE OSTI2021

Green hydrogen from microalgal liquefaction byproducts with ammonia recovery and effluent recycle for developing circular processes

Hydrothermal liquefaction is a promising technology for microalgae-based biofuel production. However, hydrothermal liquefaction’s aqueous wastes have little established reuse, and contain significant fractions of toxic ammoniacal nitrogen. Careful reuse of this waste can assure microalgae-based biofuels are produced with less environmental impact and larger energy efficiency. Microbial electrolysis cells were investigated to valorize this waste product by converting the leftover organics into hydrogen and remove ammonia. Waste hydrothermal liquefaction aqueous phase from two microalgal strains, Tetraselmis sp. and Chlorella sp. were used as feedstocks for hydrogen production in microbial electrolysis cells. Chlorella and Tetraselmis aqueous phase-fed microbial electrolysis cells reach an average current density of 5.1 ± 0.19 A/m 2 and 3.8 ± 0.08 A/m 2 . Compound removal rates and mass removal percentages were also investigated for each feedstock. Additionally, acetic acid, propionic acid, ethanol, and glycerol were effectively removed from the aqueous byproduct. Further, microbial electrolysis cells separated up to 34.3% of ammoniacal nitrogen present in the aqueous phase. Charge transfer analysis indicated that proton transfer, not ammonium transfer, contributed to the majority of the hydrogen production in the cathode. Finally, the microbial electrolysis cell effluent was reused to grow the same microalgal strains, leading to the development of a circular biofuel production system. Microalgae regrowth studies using microbial electrolysis cell effluent showed nearly complete removal of total organic carbon, but significantly less removal of total nitrogen. Tetraselmis sp. growth occurred with the Tetraselmis-derived MEC effluent, however, the control medium without effluent produced the most growth. These findings support the possibility of a circular biofuel framework using MECs, but additional constraints, including the removal of inorganic contaminants, are necessary to realize the circular processes.

09 BIOMASS FUELS↗

DOE OSTI2020

Modular scalable power conversion

A cascaded architecture composed of interconnected blocks that are each designed to process constant power and eliminate bulk energy storage are provided. Further, local controls within each block natively achieve both block- and system-level aims, making the system modular and scalable. Further methods of providing power conversion using such interconnected clocks are also provided.

Maksimovic, Dragan↗

DOE OSTI2020

Tensile properties of 3D-printed wood-filled PLA materials using poplar trees

Fabrication of renewable materials through additive manufacturing using wood-filled polylactic acid (PLA) is an emerging field of study. The variability in the tensile properties of 3D-printed materials due to the variability in woody biomass properties has not been studied. Biomass size reduction, filament extrusion, and 3D-printing methods were investigated to determine the conditions that resulted in consistent printing. Using 20% ball-milled poplar reinforcement in PLA, 210 °C filament extrusion temperature and 230 °C printing temperature were found to be the best conditions. Subsequently, seventy poplar samples from a common garden were used to test the tensile properties of the printed materials. The median tensile strength at yield was 50 MPa, with 5–95 percentiles ranged in 37–54 MPa. Strain% at break had a median value of 2.1%, and 5–95 percentiles were 1.7–2.7%. The median Young's modulus was 3.65 GPa, and 5–95 percentiles ranged in 2.9–4.1 GPa. Biomass density was correlated to composite density. Median particle size of ball-milled poplar was negatively correlated with tensile strength. Composite density affected tensile strength of the composite. β-glycosidic bond of polysaccharides in biomass affected Young's modulus of the composite. Overall, these data show that genotypic variation among Populus trichocarpa have substantial effect on tensile properties of 3D printed PLA-poplar materials.

36 MATERIALS SCIENCE↗