Search NASA⌕ Search

Engineering topics

Ross, Michael

Publications and source records attributed to Ross, Michael.

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

UHTC-TPMS Heat Exchangers for Concentrating Solar Power Applications with Thermal Energy Storage in Molten Chlorides

Concentrating solar power (CSP) plants convert energy from sunlight into electricity. Generally, a heliostat field is used to reflect sunlight and concentrate it onto a receiver, which heats the receiver and/or the media flowing through it. A flow loop transports the media through the system to a heat exchanger before returning the media back to the receiver to be reheated. The heat extracted by the heat exchanger is then converted into electricity using a conventional heat engine.

14 SOLAR ENERGY↗
DOE OSTI2024

Experimental Validation of a Modular All-Electric Power Take-Off Topology for Wave Energy Converter Enabling Marine Renewable Energy Interconnection

Power electronic converters are an enabling technology for the emerging marine energy applications, such as using ocean waves to produce electricity. This paper outlines the power take-off system and its key components used in a wave energy converter offering modularity and scalability to generate power efficiently. The proposed power take-off system was implemented based on a modular multilevel converter and could be deployed to convert any alternating current electrical energy to a different alternating current for interconnection to grid or non-grid applications. Examples of widespread deployment are supplying electricity to coastal communities or producing clean drinking water. The analysis using both the simulation tests and laboratory experiments verified the design objectives and basic functionality of the developed power take-off system. An acceptable response using a field programmable gate array-based controlled laboratory testbench was achieved, complying with guidelines specified in the prevalent industry standards. Seamless operation during steady-state and transients for the studied wave energy converter was achieved as supported by the obtained results. The key findings of this work were experimentally examined under different load conditions, direct current bus voltage fluctuations, and generator speed–torque regulation. The ability of the power take-off system to generate high-power quality of the waveforms, e.g., against adhering to the IEEE 519-2022 standard for total harmonic distortion limits, is also confirmed.

Engineering↗
DOE OSTI2022

SIESTA a Fatigue Solution: User's and Theory Manual

This report documents the fatigue code SIESTA that has been used for recently here at Sandia National Laboratories. It is written in two parts: the first as a user manual and the second as a theory manual. Currently employed in SIESTA are stress-life cycle approaches. Clients have requested the use of standards in particular analyses; therefore, the American Society of Mechanical Engineers, Boiler Pressure Vessel Code fatigue standards have been implemented. These include an elastic, an elastic-plastic, and a weld fatigue method. All three methods use a Max-Min cycle counting method that is appropriate for non-proportional loading. A Signed von Mises method that used a Rainflow Cycle Counting Method is also implemented. The Signed von Mises with the Rainflow Cycle Counting Method is appropriate for proportional loading. Several verification examples are noted and include comparisons to experimental data.

42 ENGINEERING↗
DOE OSTI2021

A Comparative Study of Joint Modeling Methods and Analysis of Fasteners [Slides]

Motivation: Crucial aspect of mechanical design is joining methodology of parts. Ability to analyze joint and fasteners in system for structural integrity is fundamental. Different modeling representations of fasteners include spring, beam, and solid elements. Various methods compared for linear system to decide method appropriate for design study. New method for modeling fastener joint is explored from full system perspective. Analysis results match well with published experimental data for new method.

42 ENGINEERING↗
NASA NTRS1993

On the performance of Trellis coded modulation with octal phase shift keying over the TDRSS channel

As the National Aeronautics and Space Administration moves into the 21st century with programs like Space Station Freedom, a manned mission to Mars, and the new Landsat mission, transmission demands on the Tracking and Data Relay Satellite System (TDRSS) will very likely exceed the available bandwidth. The Manual Lujan, Jr. Center for Space Telemetering and Telecommunications Systems (CSTTS) at New Mexico State University (NMSU) is studying techniques for increasing the data rate capabilities of TDRSS. These techniques include the use of advanced bandwidth efficient modulation formats to increase the data rate that can be sustained in a TDRSS transponder and the use of lossless bandwidth compression of the data to be transmitted to lower the data rate required from the user spacecraft. Based upon current technology the most promising bandwidth efficient modulation technique is Trellis Coded Modulation (TCM) operating with Octal Phase shift Keying (8PSK). Trellis Coded Modulation coding with 8PSK carrier modulation has the capability to increase the data rate which can be transmitted through the TDRSS spacecraft by a factor of 2 to 2.5 times that available with todays coded QPSK systems with only a small penalty in link performance relative to the existing systems. However, before NASA can safely employ TCM coding it is necessary to prove that this complex format can perform on the real TDRSS link as it does in labs and simulation studies. This proof-of-concept test over a live satellite channel was the objective of the construction and testing performed under this task of the NMSU NASA grant referenced above. In conjunction with NASA, NMSU's CSTTS has constructed a system to test a new candidate TDRSS modulation scheme, TCM 8PSK, that can enhance the information throughput of the TDRSS spacecraft. The test system for this project which was constructed over a period of 18 months by NMSU consisted of two racks of commercial and univeristy-designed and -built equipment. This project has included modifications of an existing White Sands Ground Terminal (WSGT) High Rate QPSK Demodulator to demodulate 8PSK as well as the construction of other support hardware. Also, two TCM codecs (coder/decoders) have been constructed to implement two levels of bandwidth efficiency. One was designed and built by the research team at NMSU while the other was created by the University of Notre Dame with the University of South Australia. The NMSU codec achieves a 2-to-1 increase in data rate per unit bandwidth with a coding gain relative to QPSK of about 3dB. The Notre Dame/South Australia codec achieves a 2.5-to-1 increase in data rate per unit of occupied bandwidth and a coding gain of about 2dB.

Osborne, William P.↗
NASA NTRS1993

Telemetering and telecommunications research

The New Mexico State University (NMSU) Center for Space Telemetering and Telecommunications systems is engaged in advanced communications systems research. Four areas of study that are being sponsored concern investigations into the use of trellis-coded modulation (TCM). In particular, two areas concentrate on carrier synchronization research in TCM M-ary phase shift key (MPSK) systems. A third research topic is the study of interference effects on TCM, while the fourth research area is in the field of concatenated TCM systems.

Osborne, William↗
NASA NTRS1989

A comparison of the Shuttle remote manipulator system and the Space Station Freedom mobile servicing center

The Shuttle Remote Manipulator System is a mature system which has successfully completed 18 flights. Its primary functional design driver was the capability to deploy and retrieve payloads from the Orbiter cargo bay. The Space Station Freedom Mobile Servicing Center is still in the requirements definition and early design stage. Its primary function design drivers are the capabilities: to support Space Station construction and assembly tasks; to provide external transportation about the Space Station; to provide handling capabilities for the Orbiter, free flyers, and payloads; to support attached payload servicing in the extravehicular environment; and to perform scheduled and un-scheduled maintenance on the Space Station. The differences between the two systems in the area of geometric configuration, mobility, sensor capabilities, control stations, control algorithms, handling performance, end effector dexterity, and fault tolerance are discussed.

Taylor, Edith C.↗