Search NASA⌕ Search

Engineering topics

Sawyer, J. W.

Publications and source records attributed to Sawyer, J. W..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Pressure and heating-rate distributions on a corrugated surface in a supersonic turbulent boundary layer

Drag and heating rates on wavy surfaces typical of current corrugated plate designs for thermal protection systems were determined experimentally. Pressure-distribution, heating-rate, and oil-flow tests were conducted in the Langley Unitary Plan wind tunnel at Mach numbers of 2.4 and 4.5 with the corrugated surface exposed to both thick and thin turbulent boundary layers. Tests were conducted with the corrugations at cross-flow angles from 0 deg to 90 deg to the flow. Results show that for cross-flow angles of 30 deg or less, the pressure drag coefficients are less than the local flat-plate skin-friction coefficients and are not significantly affected by Mach number, Reynolds number, or boundary-layer thickness over the ranges investigated. For cross-flow angles greater than 30 deg, the drag coefficients increase significantly with cross-flow angle and moderately with Reynolds number. Increasing the Mach number causes a significant reduction in the pressure drag. The average and peak heating penalties due to the corrugated surface are small for cross-flow angles of 10 deg or less but are significantly higher for the larger cross-flow angles.

Sawyer, J. W.↗
NASA NTRS1977

Aerothermal and structural performance of a cobalt-base superalloy thermal protection system at Mach 6.6

A flightweight, metallic thermal protection system (TPS) applicable to reentry and hypersonic vehicles was subjected to multiple cycles of both radiant and aerothermal heating in order to evaluate its aerothermal performance and structural integrity. Good structural integrity and thermal performance were demonstrated by the TPS under both a radiant and aerothermal heating environment typical of a shuttle entry. The shingle-slip joints effectively allowed for thermal expansion of the panel without allowing any appreciable hot gas flow into the TPS cavity. The TPS also demonstrated good structural ruggedness.

Sawyer, J. W.↗
NASA NTRS1976

Flutter and buckling of general laminated plates

An anisotropic buckling and flutter analysis is developed with allowance for both bending-extensional coupling and bending-twisting coupling within the framework of linear small deflection theory for simply supported general laminated plates. The extended Galerkin method is used to obtain approximate solutions to the coupled governing equations. The effects of various anisotropic stiffness parameters on the static and dynamic stability of laminated plates are evaluated, with particular emphasis on assessing the range of applicability of classical orthotropic plate theory. It is shown that bending-extensional coupling and bending-twisting stiffness terms have a destabilizing effect on buckling and flutter, the effect being more pronounced for a small number of layers. For symmetric plates, the number of layers required for orthotropic plate theory to be applicable is generally less for the buckling problem than for flutter. For square plates, aligning the fibers with the direction of airflow over the plate surface results in the highest flutter dynamic pressure.

Sawyer, J. W.↗
NASA NTRS1975

Flutter of laminated plates in supersonic flow

A solution procedure was developed using linear small deflection theory for the flutter of simply supported laminated plates. For such plates, the bending and extensional governing equations are coupled and have cross-stiffness terms which do not appear in classical plate theory. An extended Galerkin method is used to obtain approximate solutions to the governing equations, and the aerodynamic pressure loading used in the analysis is that given by linear piston theory with flow at arbitrary cross-flow angle. A limited parametric study was conducted for typical laminated composite plates. The calculations show that both the bending-extensional coupling and the cross-stiffness terms have a large destabilizing effect on flutter. Since classical plate theory does not consider bending-extensional coupling and cross stiffness terms, it usually gives inaccurate and nonconservative flutter boundaries for laminated plates.

Sawyer, J. W.↗
NASA NTRS1975

Performance of full size metallic and RSI thermal protection systems in a Mach 7 environment

The integrity and reusability of three flight-weight metallic and RSI thermal protection systems, designed for the Shuttle entry environment, have been demonstrated. Each model successfully survived over 23 entry thermal cycles without serious degradation. The metallic systems were more tolerant of the hostile environment and provided a higher degree of reusability than did the RSI. Thermal expansion slip joints of the metallic TPS successfully prevented hot gas ingress to the substructure. The RSI demonstrated high damage tolerance and field repairs increased its reusability. Heat-transfer tests to further assess RSI gap heating indicate that stacked tile orientations may impose a penalty on tile thickness. Parameters influencing RSI impingement heating were determined, and the heating data were correlated.

Bohon, H. L.↗
NASA NTRS1975

Supersonic flutter of panels loaded with inplane shear

A modal flutter analysis for biaxially loaded, orthotropic panels, using linear piston-theory aerodynamics, was extended in order to include the effects of inplane shear loading. Flutter boundaries for shear loads up to buckling are calculated for simply supported, isotropic panels of various length-width ratios and for a square, isotropic panel with elastic boundary conditions along the leading and trailing edges. These flutter boundaries are used to define conservative design curves. Sample calculations made using these design curves indicate that practical panels, which have otherwise been adequately designed, could become flutter critical if the inplane shear loads approach the buckling value.

Sawyer, J. W.↗
NASA NTRS1974

Deployment and performance characteristics of 1.5-meter supersonic attached inflatable decelerators

Attached-inflatable-decelerator (AID) canopies fabricated from lightweight Nomex cloth and tapes were deployed in a supersonic stream from the base of a 140 deg conical aeroshell. Characteristics of the deceleration system were obtained over a wide range of Mach number, dynamic pressure, and pitch angle. All models deployed rapidly by ram air and experienced only mild deployment shock loads. Steady-state drag coefficients as high as 1.3 were obtained in the supersonic stream and were relatively insensitive to Mach number, dynamic pressure, and pitch angle. All models were free of fluttering motion. Results also showed that the AID is aerodynamically more efficient without a burble fence in a supersonic stream. Though measured meridian-tape loads were higher than those predicted by theory, the ram-air deployment rates and steady-state drag coefficients were in good agreement with theory. These results indicate that the AID is a stable, efficient decelerator in a supersonic stream and its performance is readily predictable.

Bohon, H. L.↗
NASA NTRS1974

Flutter of elastically supported orthotropic panels including the effects of flow angle

A theoretical panel flutter analysis and computer program was developed which is capable of analyzing an orthotropic panel with in-plane loads, at various angles of cross flow and various edge-support conditions. The resulting modal analysis uses linear piston-theory aerodynamics and includes both aerodynamic and structural damping. Calculations made for typical panels with no in-plane forces show that large reductions in dynamic presure for flutter are possible with only small changes in flow angle. The reduction in dynamic pressure with flow angle is greater for elastically supported panels than for simply supported panels. Aerodynamic damping has a significant stabilizing effect at all flow angles except zero, whereas structural damping has negligible effect.

Sawyer, J. W.↗
NASA NTRS1973

Orthotropic panel flutter at arbitrary yaw angles - Experiment and correlation with theory.

Experimental flutter boundaries were obtained for yaw angles between 15 and 90 deg at Mach numbers 2 and 1.6 for panels mounted on a remotely controlled turntable. Good definition of the flutter boundaries was obtained by rotating the panels into and out of flutter. Two types of specimens were tested: a single-sheet corrugated panel having a length-to-width ratio of 5 on clamped supports, and several square doubly-corrugated panels on various flexible supports. Calculated flutter speeds based on quasi-steady aerodynamics are compared to experimental data.

Shyprykevich, P.↗
NASA NTRS1972

Subsonic pressure distributions around a solid model of an inflatable decelerator attached to the base of an ogive-cylinder

A wind-tunnel investigation was conducted at free-stream Mach numbers from 0.20 to 1.00 and corresponding Reynolds numbers, based on maximum afterbody diameter, from 2.25 x one million to 6.90 x one million on a solid model of an attached inflatable decelerator (AID) connected to the base of an ogive-cylinder. Tests were conducted to obtain ram-air and surface pressure distributions about the AID. AID shapes derived for subsonic deployment are dependent on the pressure distributions used in their derivation, and the different shapes obtained are dependent on the Mach number for which the design is made. The resulting pressure distributions were used in a design program to obtain new shapes which were compared with the original pressure-distribution shape.

Sawyer, J. W.↗
NASA NTRS1971

Subsonic and transonic pressure distributions around a bluff afterbody in the wake of a 120 deg cone for various separation distances

A wind-tunnel investigation was conducted at free-stream Mach numbers from 0.20 to 1.00 and Reynolds numbers, based on maximum afterbody diameter, from 2.25 million to 6.90 million on solid models of an attached inflatable decelerator (AID) concept. Tests were conducted to obtain static and ram surface pressure distributions about the basic shapes and at various separation distances between the 120 deg conical forebody and the inflated afterbody shape. The resulting data were used to study the feasibility of extracting a payload from a conical forebody by means of an AID.

Sawyer, J. W.↗