Engineering topics

Schultz, B. E.

Publications and source records attributed to Schultz, B. E..

4 records

NASA NTRS1994

Precision orbit determination for TOPEX/POSEIDON

The TOPEX/POSEIDON mission objective requires that the radial position of the spacecraft be determined with an accuracy better than 13 cm RMS (root mean square). This stringent requirement is an order of magnitude below the accuracy achieved for any altimeter mission prior to the definition of the TOPEX/POSEIDON mission. To satislfy this objective, the TOPEX Precision Orbit determination (POD) Team was established as a joint effort between the NASA Goddard Space Flight Center and the University of Texas at Austin, with collaboration from the University of Colorado and the Jet Propulsion Laboratory. During the prelaunch development and the post launch verification phases, the POD team improved, calibrated, and validated the precision orbit determination computer software systems. The accomplishments include (1) increased accuracy of the gravity and surface force models and (2) improved peformance of both laser ranging and Doppler tracking systems. The result of these efforts led to orbit accuracies for TOPEX/POSEIDON which are significantly better than the original mission requirement. Tests based on data fits, covariance analysis, and orbit comparisons indicate that the radial component of the TOPEX/POSEIDON spacecraft is determined, relative to the Earth's mass center, with an root mean square (RMS) error in the range of 3 to 4 cm RMS. This orbit accuracy, together with the near continuous dual-frequency altimetry from this mission, provides the means to determine the ocean's dynamic topography with an unprecedented accuracy.

Tapley, B. D.↗

NASA NTRS1994

Dynamic orbit determination using GPS measurements from TOPEX/POSEIDON

The GPAS data acquired by the TOPEX/POSEIDON (T/P) Demonstration Receiver (DR) have been used in a dynamic orbit determination, which was based on the description of the gravitational and nongravitational forces in the equations of motion. The GPS carrier phase data were processed in a double difference mode to remove clock errors, including the effects of Selective Availability. Simultaneous estimation of the T/P orbit and GPS orbits was performed using five 10-day cycles in the interval between December (1992) and April (1993). The resulting T/P orbits have been compared with the orbits determined from Satellite Laser Ranging, the French one-way Doppler tracking system, DORIS, and with the JPL reduced dynamic orbit determination strategies and force models with the GPS/DR to those used with SLR/DORIS, the radial component of the T/P orbit (based on JGM-2) was found to agree better than 30 mm (rms) and 35 mm with the JPL reduced dynamic orbit. An experiment gravity tuning was accomplished using four cycles of GPS/DR data. The resulting GPS./DR-orbits, determined by the dynamic technique with the experimental gravity field, are in better agreement with the JPL reduced dynamic orbits in both the radial component (21-25 mm) and altimeter crossover residuals than the JGM-2 orbits. (21-25 mm) and altimeter crossover residuals than the JGM-2 orbits.

Schultz, B. E.↗

NASA NTRS1985

Station coordinates, baselines, and earth rotation from Lageos laser ranging - 1976-1984

The orbit of the Lageos satellite is well suited as a reference frame for studying the rotation of the earth and the relative motion of points on the earth's crust. The satellite laser measurements can determine the location of a set of tracking stations in an appropriate terrestrial coordinate system. The motion of the earth's rotation axis relative to this system can be studied on the basis of the established tracking station locations. The present investigation is concerned with an analysis of 7.7 years of Lageos laser ranging data. In the first solution considered, the entire data span was used to adjust a single set of station positions simultaneously with orbit and earth rotation parameters. Attention is given to the accuracy of earth rotation parameters which are determined as an inherent part of the solution process.

Tapley, B. D.↗

NASA NTRS1983

Closed-loop strain controlled testing at elevated temperatures with a non-contacting gage

Normal strains were measured over a 100 micron gage length at a distance of 50 microns from the edge of a notch using a non-contacting, laser-based interferometric technique. Tests were performed at 600 C under direct strain control from this interferometric 'micro-gage'. A minicomputer system, that produced a voltage analog of strain as a final output, controlled the strain measuring apparatus. This analog output was used directly as the feedback signal to a closed-loop, electrohydraulic mechanical test system. This allowed both strain rate and strain amplitude to be controlled at the notch root of the specimen.

Martin, J. F.↗