Search NASA⌕ Search

Engineering topics

Servis, Anna G.

Publications and source records attributed to Servis, Anna G..

Kinetics and Mechanism of Ce(IV) Phase Transfer by the Neutral Extractants Tributyl Phosphate and N,N -Di(2-ethylhexyl)isobutyramide

Tributyl phosphate and N,N-di(2-ethylhexyl)isobutyramide (DEHiBA) are uranium-selective extractants that could be used to recover low-enriched uranium from commercial used nuclear fuel. The economic viability of liquid-liquid extraction processes for chemical separations depends on both thermodynamic and kinetic considerations. Here we used microfluidic droplet extraction to measure interfacial phase transfer rate constants for the extraction and stripping of Ce(IV), a non-radioactive actinide surrogate. The Damkohler numbers for each system were calculated and the phase transfer processes were determined to be diffusion-limited under all conditions, contrary to prior studies using constant interface stirred cells and single drop methods. A well-extracted 2:1 DEHiBA/Ce(IV) complex in the organic phase was determined from batch distribution studies, suggesting a different extraction mechanism for Ce(IV) compared with poorly extracted Pu(IV). Finally, phase disengagement rates were found to be rapid in both systems, in agreement with other studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rapid Quantification of 237 U Specific Activity for Nuclear Forensics

In the event of an unattributed nuclear explosion, rapid assessment of the short-lived uranium isotope activity and mass can provide valuable information for subsequent forensic analysis. Rapid analysis in the field is enabled by using microfluidic chemistry and deployable instrumentation. Here, this work presents a flow chemistry system, controlled in LabVIEW, that integrates three functionalities: (1) selective extraction of uranium from the sample matrix via a 3D-printed supported liquid membrane module; (2) UV–visible absorbance spectrophotometry to measure the total uranium concentration in the strip flow; and (3) a portable CdTe γ-ray spectrometer coupled to a 3D-printed flow cell to measure 237 U activity concentration in the strip solution. The system was calibrated using standard solutions, and its functionality was demonstrated using a solution of depleted uranium spiked with 237 U. Uranium concentrations of 40–5000 μg/mL were directly quantified online using a 100 mm optical flow cell, while concentrations of 0.5–10 μg/mL were quantified online using a colorimetric reagent. The mass concentration measurement takes approximately 60 min while the activity concentration via γ-ray spectrometry varies depending on the activity of 237 U, with 1 kBq/mL requiring about 30 min of acquisition time to obtain <10% uncertainty at 1σ. This platform provides a fieldable approach for quantifying uranium mass and radioactivity relevant to postdetonation nuclear debris.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Kinetics and Mechanism of Tetravalent Cerium Extraction by Di-2-Ethylhexyl Isobutyramide (DEHiBA)

DEHiBA is a fully-incinerable, CHON extractant with a high selectivity for hexavalent actinides. However, as a recently-developed ligand, much remains unknown about its physical and chemical properties, including its extraction and phase disengagement rates. Here, we present data on the phase transfer kinetics of Ce(IV) extraction and stripping by both DEHiBA and TBP collected using microfluidic devices. Ce(IV) was selected as a surrogate for Pu(IV) and Np(IV) in the initial tests of the microfluidics system prior to testing with the actinides. Pseudo first-order reaction rate constants are determined for both systems, and the corresponding Damköhler numbers (Da) are calculated to establish whether the extraction and stripping processes are kinetically or diffusion controlled. The stoichiometry of the extracted Ce(IV)-DEHiBA complex is determined, and the phase disengagement properties under extraction conditions are assessed using the dimensionless dispersion number. A possible explanation for the favorable extraction of Ce(IV) by DEHiBA, which is known to poorly extract many tetravalent cations, is presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modular, disposable 3D printed microfluidic membrane system for separation and purification

The present disclosure relates to a membrane extraction apparatus for extracting a component from a first liquid. The apparatus may incorporate a housing comprised of first and second mating housing halves, with each housing half having an open faced channel formed therein such that the channels at least partially overlay one another when the two housing halves are secured together. A membrane filter is disposed between the two housing halves to overlay the open faced channels. The membrane filter extracts the component from the first liquid and transfers the component into the second liquid as the first and second liquids flow through the first and second housing halves.

Servis, Anna G.↗

Partitioning of Radionuclides in Various Streams of the Mo-99 Purification Process

The Universal Neutron Irradiator (UNI) was designed to irradiate a small volume of uranium solution and to achieve high fission power without creating a large radionuclide (RN) inventory. The UNI system is equipped with a fully enclosed off-gas system with online hydrogen gas monitoring to prevent the production of an explosive atmosphere, as well as storage cylinders for capturing fission gases. It also includes a catalytic recombiner in the target capsule (to immediately recombine radiolytic hydrogen and oxygen gas in the system) and access ports for sampling the target solution and capsule headspace. In UNI Phase I experiments, 50 mL of uranyl sulfate solution was irradiated at 0.3–0.5 W/mL fission power using a tantalum target assembly to produce photoneutrons via irradiation with an electron beam. The purposes of the Phase I experiments were to test the efficacy of adding 200 ppm Fe 2+ to the target solution to prevent uranyl peroxide precipitation under representative irradiation conditions, and to monitor iodine speciation in the irradiated uranyl sulfate solution. The focus of the UNI Phase II experiments was to use an irradiated uranyl sulfate solution containing a mixture of fission products and monitor their distribution in various streams during the primary recovery column (titania-based column) that separates Mo-99 from uranium. Irradiations were designed to create sufficient activity for tracking their distribution in various processing streams using a combination of gamma counting and inductively coupled plasma mass spectrometry (ICP-MS) analyses. Obtained data will be used to better understand the composition of waste streams, accumulation of RN on the titania column, and identify what RNs accumulate in the uranyl sulfate solution. Furthermore, this knowledge will allow us to determine waste classifications for various streams produced during the Mo-99 purification process and develop an appropriate waste clean-up strategy.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Impact of Irradiation and Decay Time on Chemical Speciation in Uranyl Sulfate Solution

A pH-1, 200-g U/L, highly enriched uranyl sulfate solution was neutron-irradiated using an accelerator-driven neutron source (the Universal Neutron Irradiator, UNI) to fission U-235 under conditions similar to those used by SHINE to produce Mo-99 in a subcritical assembly. We completed a series of five uranyl sulfate irradiations to assess the impact of irradiation and decay time on uranium precipitation and iodine speciation in solution. The duration of each irradiation was increased in order, with the shortest irradiation taking 2.9 hours and the longest, 64.5 hours. A total of 9.5E16 U-235 nuclei were fissioned in all irradiations, and a maximum fission power density of 0.26 W/mL was reached in the final irradiation. We observed no evidence of uranyl peroxide or other precipitates, demonstrating that the addition of Fe 2+ to a final Fe concentration of 200 ppm in the target solution was successful at preventing precipitation under representative irradiation conditions. Nonvolatile I - was found to be the dominant (>70%) iodine species in solution, both immediately after irradiation and after days to weeks of decay time.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Purification and Concentration of 99 Mo from a UREX raffinate

The medical isotope 99m Tc ( t ½ = 6.0 h) accounts for over 80% of isotopes used in diagnostic nuclear medicine today and is normally derived from its transient equilibrium parent 99 Mo ( t ½ = 66 h). To reduce U.S. dependence on 99 Mo derived from HEU by foreign suppliers, the NNSA/M3 program—under the American Medical Isotope Production Act—has been tasked with facilitating the work of domestic 99 Mo suppliers that do not utilize HEU. Superconducting electron linear accelerators with high-Z converter targets can generate bremsstrahlung photons and neutron fluxes that can induce photonuclear reactions and LEU fission. After sufficient production intervals, targets can be rotated out and processed while another batch is irradiated. The process flow chemistry is shown in Figure 1. The irradiated U 3 O 8 targets are retrieved and dissolved in HNO 3 ; the volatile fission products are expelled and captured during this step. The HNO 3 liquor bearing the uranyl, fission and activation products is injected into the UREX suite of liquid-liquid extraction banks. The uranyl is partitioned in typical fashion using tri-$\textit{n}$-butyl phosphate (TBP) in a hydrocarbon diluent. The raffinate—comprising mainly 99 Mo and fission products—is then injected into the MoLLE (Molybdenum Liquid-Liquid Extraction) flowsheet, where the Mo is selectively extracted by an organophosphorous acid extractant such as di-(2-ethylhexyl phosphoric acid) (HDEHP). Trace amounts of Nb, Zr, Np, I, and Te are co-extracted. The Mo is stripped using acetohydroxamic acid (AHA) and fed onto an anion exchange column. Following a series of hydroxide, HCl, and oxalic acid wash steps, the Mo can be recovered in NaOH/NaCl. A manuscript describing this process chemistry in more detail was recently published.

07 ISOTOPE AND RADIATION SOURCES↗

Removal of Tc-99, Zr-95, and Nb-95, From Solutions Obtained After Dissolution of Irradiated Mo Targets

Decontamination of 99 Tc, Nb, and Zr impurities in dissolved irradiated Mo disks can be accomplished using Fe(II) precipitation. Here, we report bench-scale experiments and large-scale demonstrations on removal of 99 Tc (0.1 mM), 95 Nb, and 95 Zr from dissolved Mo disk simulant solutions. Tc removal is accomplished through the reduction and simultaneous immobilization of Tc(VII) by Fe(II), producing an insoluble, Tcincorporated Fe(II)-Fe(III) solid that is removed by filtration. Large-scale testing showed that Tc (97.6% ± 1.7%) is removed without affecting 99 Mo yields. Other important side reaction product impurities in irradiated Mo targets, namely various isotopes of Nb and Zr, are also removed (>99%) in this process. The effects of metal (Fe, Tc, Mo) concentrations, Fe(II)/Fe(III) ratio, pH, temperature, Fe addition method, and hydrogen peroxide addition were tested. The minimum amount of Fe(II) needed to remove up to 99% Tc is 10 mM and the optimal pH value for simultaneous removal of Tc, Nb, and Zr impurities is pH 13.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Separation and purification of Mo-99 produced from natural U 3 0 8 targets via photo-fission

The most-used medical isotope is 99m Tc (t½ = 6.0 h), which comprises over 80% of isotopes used in nuclear medicine today. It is normally derived from its transient equilibrium parent 99 Mo (t½ = 66 h). A recent surge of interest in using the more proliferation-resistant low-enriched uranium (LEU) under the American Medical Isotope Production Act (AMIPA) has presented this technical challenge: can a domestic supplier meet the estimated weekly U.S. demand of 1500 6–day Ci of 99 Mo?

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Recovery of high specific activity molybdenum-99 from accelerator-induced fission on low-enriched uranium for technetium-99m generators

Abstract A new process was developed to recover high specific activity (no carrier added) 99 Mo from electron-accelerator irradiated U 3 O 8 or uranyl sulfate targets. The process leverages a novel solvent extraction scheme to recover Mo using di(2-ethylhexyl) phosphoric acid following uranium and transuranics removal with tri- n -butyl phosphate. An anion-exchange concentration column step provides a final purification, generating pure 99 Mo intended for making 99 Mo/ 99m Tc generators. The process was demonstrated with irradiated uranium targets resulting in more than 95% 99 Mo recovery and without presence of fission products or actinides in the product.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Chemical Understanding of Actinide Separations

This work provides a broad overview of the separation processes used to isolate actinides and the experimentally and computationally determined chemical characteristics that define those separations. The redox chemistry of the actinides plays a pivotal role in both aqueous and pyrochemical processing separations. The near-overlapping energies of the 6d and 5f orbitals in the light actinides allow for facile adjustment of actinide oxidation states, which is used in many established separation methods. In contrast, the stable, generally 3+ oxidation states of the mid- and heavy actinides can make it difficult to separate them from the similarly lanthanides(III). In aqueous separations, the tendency of the actinides to form anionic and neutral aqueous complexes with a variety of complexants (especially soft donors) is used to achieve high separation factors between chemically similar elements in both solid–liquid separations and liquid–liquid extraction. This selectivity can be further tuned through the use of specialized organic or solid-phase ligands. Pyroprocessing separations utilize the unique redox behavior of the actinides to adjust their distribution between a molten salt electrolyte and either a solid electrode or molten metal phase. Atomic-level insights into the mechanisms underlying actinide separation processes, with the ultimate goal of predicting separation behavior, can be provided by electronic structure and statistical mechanical-based calculation methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Transport Modeling of Kinetically Limited Microscale Extraction Systems: Droplet and Supported Liquid Membrane Separations

Microfluidic droplet extraction devices can be used to efficiently measure solute phase transfer kinetics in liquid–liquid extraction systems. In this work, a droplet extraction apparatus was constructed using off-the-shelf and custom 3D printed parts for less than 110 USD. The interfacial kinetics of the transfer of Pu(IV) between an aqueous nitric acid phase and a 5 v/v% tridodecylamine (TDA) in toluene phase were characterized by determining the extent of Pu(IV) transfer between phases at different flow rates. Forward interfacial rate constants calculated from this data using an analytical model are 5.6 × 10 –3 mm s –1 under extraction (aqueous-to-organic solute transfer) conditions and 3.3 × 10 –3 mm s –1 under stripping (organic-to-aqueous solute transfer) conditions. The analytical model is valid when the rate of solute transfer across the interface between the two liquid phases has pseudo-first-order reversible reaction kinetics and is slow relative to the rate of solute transport to the interface. The change in the outlet concentration with residence time determined using the analytical model was compared with the results of a numerical model accounting for advection/diffusion to the interface in addition to kinetically limited interfacial solute transfer. These calculations revealed that for systems with forward interfacial rate constants greater than approximately 10 –2 mm s –1 , the analytical model must be supplemented with a numerical transport model accounting for an additional advection/diffusion mass transfer resistance. This threshold corresponds to a Damköhler number of one. The measured interfacial kinetic rate constants for Pu(IV)/TDA were used in a supported liquid membrane (SLM) numerical model, which showed that the Pu(IV) phase transfer kinetics are fast enough for use in a practical separation.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

3D Printed Microfluidic Supported Liquid Membrane Module for Radionuclide Separations

Microfluidic supported liquid membrane extraction is a promising technique for microliter-scale radionuclide separations because it requires very small reagent volumes and combines extraction and stripping in a single unit operation. Flat sheet supported liquid membrane (FS-SLM) modules with 100, 200, 300, and 400 μm deep channels were fabricated at a cost of less than 5 USD in material using a commercially available resin three-dimensional (3D) printer. The performance of these modules was characterized by quantifying uranium transport across a 15 v/v% tributyl phosphate (TBP) liquid membrane at flow rates between 5 and 60 μL min –1 and developing a two-dimensional (2D) numerical transport model for the system. The extent of uranium extraction was found to increase with increasing residence time and decreasing channel depth, with quantitative extraction occurring at the slowest flow rates and shallowest channel depths. The numerical model agreed well with the experimental extraction results. Time-dependent calculations showed that the modules reach steady state in fewer than 9 min and that there is a considerable buildup of uranium in the membrane during that time.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗