Engineering topics
Shaffer, Scott
Publications and source records attributed to Shaffer, Scott.
NASA-ISRO Synthetic Aperture Radar (NISAR) Mission
NISAR is a multi-disciplinary Earth-observing radar mission that makes global measurements of land surface changes that will greatly improve Earth system models. NISAR data will clarify spatially and temporally complex phenomena, including ecosystem disturbances, ice sheet collapse, and natural hazards including earthquakes, tsunamis, volcanoes, and landslides. It provides societally relevant data that will enable better protection of life and property. The mission, a NASA-ISRO partnership, uses two fully polarimetric SARs, one at L-band (L-SAR) and one at S-band (S-SAR), in exact repeating orbits every 12 days that allows interferometric combination of data on repeated passes. NASA provides the L SAR; a shared deployable reflector; an engineering payload that supports mission-specific data handling, navigation and communication functions; science observation planning and L SAR data processing. ISRO provides the S-SAR, spacecraft, launch vehicle, satellite operations, and S-SAR data processing. The mission will be launched from the Satish Dhawan Space Centre, Sriharikota, India. Mission development has addressed many unique challenges and incorporates many “firsts” for a jointly-developed free-flyer radar science mission.
NISAR Model-Based Radar Antenna Pointing, Antenna Pattern and System Performance Evaluation
UNKNOWN
Impact of Gaps in the NASA-ISRO SAR Mission Swath
The NASA-ISRO Synthetic Aperture Radar (NISAR) mission will carry L-band and S-band SAR instruments, each with a 240 km swath width. The L-band instrument has the capability to map the entire Earth’s land and ice covered surfaces from both ascending and descending orbit positions, continuously in an exact 12 day repeating cycle, given temporally dense (better than 6-day on average) sampling of Earth over the life of the mission. To achieve this swath coverage without loss of resolution or polarimetric capability, NISAR uses a reflector-feed based antenna system with scan-on-receive (“SweepSAR”) capability. One of the characteristics of SweepSAR is that the pulse repetition interval of the radar is shorter than the echo receive window for the 240 km swath. Therefore, transmit events occur during the receive window and the receivers must be blanked periodically, creating gaps in the coverage. For fixed pulse rate operations, these gaps are persistent strips of blanked ranges. NISAR is being designed to allow variation of the pulse rate in order to spread out these gaps throughout the synthetic aperture, but processing these variably-acquired data is more challenging and can lead to compromises in image quality. At the highest level NISAR places requirements on science measurements rather than image quality, so there is often a debate among science and engineering team members as to whether to operate with fixed pulse rates – leading to range strips consistently blank from cycle to cycle but with optimal image quality – or to vary the pulse rate, fill in the gaps, and live with degraded image quality. NISAR’s performance team has shown that science requirements can be met with the gaps. However, scientists are eager for maximum and coverage within a swath. A companion paper (Villano et al.) describes image quality for NISAR using a variable PRF approach, but does not go further to science requirements. This paper explores the issues when gaps are present in the swath due to fixed PRF operations.
NISAR L-SAR Digital Electronics Subsystem - A Multichannel Distributed Processing System with Synchronous Timing Control for Digital Beam Forming and Multiple Echo Tracking
The NASA-ISRO Synthetic Aperture Radar (NISAR) L-band SAR instrument employs multiple digital channels to optimize resolution while keeping a large swath on a single pass. High-speed digitization with fine synchronization and digital beam forming are necessary in order to facilitate this new technique called SweepSAR. An architecture employing multiple FPGA based digital signal processors has been conceived to facilitate digital calibration on an individual channel basis as well as digital signal processing to optimize the receive signal. On-board processing and data compression has been implemented to reduce the volume of data in order to satisfy the operational requirements of near global coverage for the desired science targets. A novel command and timing architecture was developed to manage this complex system while providing detailed control of individual channel receive window timing required for digital beam forming. The NISAR L-band Digital Electronics Subsystem is the combination of the hardware, firmware and software components architected and implemented to operate this radar and return the desired quantity and quality of data for the science community.
Comparative View of Antenna/RF Subsystems between SIR-C and NISAR L-band SAR Systems for Wide-Swath Imaging
In 1994, SIR-C demonstrated ScanSAR, a mode of operating the SAR system that has become the “standard” implementation for wide-swath spaceborne imaging SAR systems. The NISAR SAR instruments introducing a new SAR architecture for wide-swath imaging call SweepSAR which is expected to have similar success. This paper compares the Antenna and RF subsystem design and the technology utilization considerations between the SIR-C planar phased array SAR system using the ScanSAR technique and NISAR off-set reflector with phased array feed using the SweepSAR technique.
NISAR L-Band Digital Electronics Subsystem: A Multichannel System with Distributed Processors for Digital Beam Forming and Mode Dependent Filtering
No abstract available
Nisar L-band Digital Electronics Subsystem
The NASA-ISRO Synthetic Aperture Radar (NISAR) L-band SAR instrument employs multiple digital channels to optimize resolution while keeping a large swath on a single pass. High-speed digitization with fine synchronization and digital beam forming are necessary in order to facilitate this new technique called SweepSAR. An architecture employing multiple FPGA based digital signal processors has been conceived to facilitate digital calibration on an individual channel basis as well as digital signal processing to optimize the receive signal. On-board processing and data compression has been implemented to reduce the volume of data in order to satisfy the operational requirements of near global coverage for the desired science targets. A novel command and timing architecture was developed to manage this complex system to meet the challenging project requirements. The NISAR L-band Digital Electronics Subsystem is the combination of the hardware, firmware and software components architected and implemented to operate this radar and return the desired quantity and quality of data for the science community.
NASA L-SAR Instrument for the NISAR (NASA-ISRO) Synthetic Aperture Radar Mission
The National Aeronautics and Space Administration (NASA) in the United States and the Indian Space Research Organization (ISRO) have partnered to develop an Earth-orbiting science and applications mission that exploits synthetic aperture radar to map Earth’s surface every 12 days or less. To meet demanding coverage, sampling, and accuracy requirements, the system was designed to achieve over 240 km swath at fine resolution, and using full polarimetry where needed. To address the broad range of disciplines and scientific study areas of the mission, a dual-frequency system was conceived, at L-band (24 cm wavelength) and S-band (10 cm wavelength). To achieve these observational characteristics, a reflector-feed system is considered, whereby the feed aperture elements are individually sampled to allow a scan-on-receive (“SweepSAR”) capability at both L-band and S-band. The instrument leverages the expanding capabilities of on-board digital processing to enable real-time calibration and digital beamforming. This paper describes the mission characteristics, current status of the L-band Synthetic Aperture Radar (L-SAR) portion of the instrument, and the technology development efforts in the United States that are reducing risk on the key radar technologies needed to ensure proper SweepSAR operations.
NASA L-SAR Instrument for the NISAR (NASA-ISRO) Synthetic Aperture Radar Mission
No abstract available