Search NASA⌕ Search

Engineering topics

Shaler, Kelsey

Publications and source records attributed to Shaler, Kelsey.

Loads assessment of a fixed-bottom offshore wind farm with wake steering

Wake steering via deliberate yaw offset is an emerging wind farm control technique that has the potential to mitigate wake losses and further increase wind farm energy yield. The loads impact of this technique has been studied, but there is limited insight into wind-farm-wide impacts of wake steering. Understanding such impacts is crucial to determining the feasibility of using wake steering in commercial wind farms. To that end, this work investigates the impacts of wake steering on the loads of all turbine components across all turbines in a wind farm operating under a broad set of inflow conditions, including inflow velocity, shear exponent, turbulence class, and inflow angle. This was done by performing FAST.Farm simulations of a 12-turbine wind farm array, excerpted from a larger hypothetical wind farm. The International Energy Agency Wind 15-MW reference wind turbine was modeled atop a monopile substructure, an open-source model that closely approximates the properties of similar commercial options. Wake steering was included via yaw offsets that were computed using an offline optimization with the National Renewable Energy Laboratory tool FLORIS. For each inflow case, the 12-turbine array was simulated with and without wake steering. Results were compared in terms of time-averaged means, standard deviations, ultimate loads, and damage-equivalent loads. The findings show that because wake steering is generally applied at rated wind speeds and below, it is unlikely to drive ultimate loads. For fatigue loads, wake steering does increase the overall fatigue accumulation for some load channels, such as blade-root and shaft bending. This is to be expected when overall power yield increases but may cause the damage accumulation to be more uniform throughout the array. The significance of the added fatigue loading is dependent on how frequent wake steering is utilized in the overall set of inflow conditions across the wind rose.

17 WIND ENERGY↗

Comparing wind turbine aeroelastic response predictions for turbines with increasingly flexible blades

Highly flexible blades are becoming more prevalent designs as a potential solution to the transportation challenges associated with large-scale wind turbine rotors. However, there is currently no quantitative definition of “highly flexible” blades. To further develop turbines with highly flexible blades, a precise definition of the term and accurate simulations of turbines with such blades are required. Assumptions made in the traditional aerodynamic model, Blade Element Momentum (BEM) theory, are violated in turbines with flexible blades. However, Free Vortex Wake (FVW) methods can more accurately model these turbine designs. Though more computationally expensive than BEM, FVW methods are still computationally tractable for use in iterative turbine design. The purpose of this work was to determine the blade flexibility at which BEM and FVW methods begin to produce diverging aeroelastic response results. This was accomplished by simulating the BAR-DRC reference turbine with increasingly flexible blades in a range of steady, uniform inflow conditions using OpenFAST, the National Renewable Energy Laboratory’s physics-based turbine engineering tool. Blade-tip deflections confirmed that BEM and FVW results diverge as blade flexibility increases. For the 212 m rotor diameter turbine used in this study, the two methods largely agreed for smaller blade deflections. But their results differed by an average of 5% when the out-of-plane blade-tip deflections exceeded 5% of the blade length and in-plane blade-tip deflections exceeded 1.25% of the blade length, with percent differences approaching 25% at the largest deflections.

17 WIND ENERGY↗

Efficient Loads Surrogates for Waked Turbines in an Array

Accurately and efficiently predicting wind turbine structural loading is a crucial step in wind farm design. Without considering structural loading, wind farm optimization could negatively impact turbine fatigue and ultimate loads, especially for waked and partially waked turbines, which could result in higher maintenance costs and reduced turbine lifetime. However, predicting turbine loads throughout an array is a costly step, as these quantities require time-accurate results across long time histories, which is often intractable for large array optimization. Therefore, surrogate models that link array spacing to load outputs are often used, but the surrogates are then unique to the inflow conditions and array configurations in the training library. This work develops surrogate models for many wind turbine load outputs based solely on rotor plane velocity measurements, with no required input about array configuration or freestream inflow parameters. Surrogate models were constructed for many turbine quantities of interest (QoI), considering mean, standard deviation, ultimate, and fatigue loads. In general, most QoI statistics were accurately captured, as measured by predicted vs. actual correlation coefficient, confirming the suitability of the approach. Temporal mean values of the QoI required only temporal mean measurements of the rotor plane inflow velocity. However, accurate prediction of temporal standard deviation, ultimate, and fatigue values of QoI also required temporal standard deviations of the rotor plane velocity field. Poor surrogate performance was observed when too many correlated inputs were used, such as multiple velocity components. If the fewest inflow parameters are used to construct the surrogates, the average correlation coefficient value for all output QoI statistics is 0.89. Surrogates for standard deviations and damage equivalent loads (DELs) of turbine QoIs generally had lower accuracy and tower-base and shaft load channels posed the most difficult to capture accurately. The results suggest that these surrogates could be easily paired with analytic wake models, which are frequently used for pre-construction wind farm array optimization, to account for turbine loading in addition to power production. By including the optimal inflow conditions, the surrogate accuracy can improve to an average correlation coefficient value for all output QoI statistics of 0.92. This work has established the ability to build accurate surrogates for mean, standard deviation, ultimate load, and DEL turbine QoI values based on the rotor plane inflow velocity, and identified which inflow conditions lead to greater surrogate accuracy.

17 WIND ENERGY↗

Numerical investigation of wind turbine wakes under high thrust coefficient

Abstract We study wind turbine wakes of rotors operating at high thrust coefficients ( C T > 24/25) using large‐eddy simulations with a rotating actuator disk model. Wind turbine wakes at high thrust coefficients are different from wakes at low thrust coefficients. Wakes behave differently at high thrust, with increased turbulence and faster recovery. Lower induction in the wake is achieved because wakes in high‐thrust conditions recover much faster than in normal operating conditions. This enhanced recovery is possible thanks to the turbulence generated in the near wake. We explore the mechanism behind this behavior and propose a simple model to reproduce it. We also propose a Gaussian fit for the wakes under high‐thrust conditions and use it use it to initialize an Ainslie type model within the FAST.Farm framework.

FAST.Farm↗

Reliability‐based layout optimization in offshore wind energy systems

Abstract Existing methods for optimizing wind array layouts typically use power or cost objectives and rarely consider reliability‐based objectives. Component and system failure rates, however, are dependent on location‐specific wind conditions, are influenced by array layout and wake interactions, and have a direct and significant impact on capital costs, operational costs, and power production. Although wind power plant models exist that calculate wind loads with sufficient resolution to capture component loading dynamics from wind conditions, they are computationally expensive and thus not suitable for research applications requiring many evaluations, particularly optimization. This study describes the development of computationally efficient, reliability‐based layout optimization methods, enabling us to explore the relationship between component reliability and layout optimization. These methods include the surrogate modeling of the planet bearing life based on varying wind conditions simulated in FAST.Farm and the formulation of reliability‐based objectives based on failure cost and power production models. Through demonstration of this method, we explore how wind conditions, objective functions, and capacity density influence reliability‐based layout optimization. Results indicate that considering reliability alongside power production can reduce failure costs associated with replacement costs and downtime while maintaining or improving power production. Our conclusions highlight the opportunity for wind power plant developers to integrate reliability and operational expenditures alongside performance and capital expenditure objectives in plant design and development to improve plant performance and costs.

17 WIND ENERGY↗

FAST.Farm Development and Validation of Structural Load Prediction Against Large Eddy Simulations

FAST.Farm is a mid-fidelity engineering tool developed by the National Renewable Energy Laboratory targeted at accurately and efficiently predicting wind turbine power production and structural loading in wind farm settings, including wake interactions between turbines. FAST.Farm is based on several principles of the dynamic wake meandering (DWM) model, but also addresses limitations of previous DWM implementations. Previous FAST.Farm studies have shown the similarities and differences between FAST.Farm and large eddy simulations for rigid turbine cases. The objective of this work is to quantify the ability of FAST.Farm to accurately predict turbine structural response in a small wind farm. This is done by comparing FAST.Farm structural response to SOWFA-OpenFAST results for three laterally-aligned turbines. The purpose of this study is to characterize the similarities and differences between FAST.Farm and a higher fidelity model for predicting turbine structural response in a wind farm for differing atmospheric inflows. Strong statistical agreement was found between FAST.Farm and SOWFA-OpenFAST structural response for the non-waked upstream turbine, and good agreement was found for the downstream turbines for most structural quantities. Higher differences were seen for downstream turbines with low ambient turbulence intensity or yawed turbines, suggesting areas for FAST.Farm wake dynamics modeling improvements. For all cases and turbines, small statistical differences were seen between blade deflections and bending moments, with larger differences for tower-top and tower-base bending moments. Overall, the results establish confidence for applying FAST.Farm to wind farm power and loads analyses and identify areas where further model validations and model improvements should be targeted.

49 EE - Wind and Water Power Program - Wind (EE-4W↗

Validation of FAST.Farm Against Full-Scale Turbine SCADA Data for a Small Wind Farm

FAST.Farm is a new midfidelity engineering tool developed by the National Renewable Energy Laboratory targeted at accurately and efficiently predicting wind turbine power production and structural loading in wind farm settings, including wake interactions between turbines. FAST.Farm is based on some of the principles of the Dynamic Wake Meandering model—including passive tracer modeling of wake meandering—but addresses many of the limitations of previous Dynamic Wake Meandering (DWM) implementations. Previous FAST.Farm verification studies show the similarities and differences between FAST.Farm and large-eddy simulations for rigid and flexible turbines. In this validation study, FAST.Farm turbine responses are compared to multiturbine measurements from a subset of a full-scale wind farm. FAST.Farm predictions of turbine generator power, rotor speed, and blade pitch for five-turbine simulations are compared to supervisory control and data acquisition results. Results reveal that FAST.Farm generator power mean and standard deviation results reasonably match measured data for upstream and downstream turbines, as well as the mean rotor speed and blade pitch above rated wind speeds. However, FAST.Farm generally underpredicts the mean rotor speed and overpredicts the mean blade pitch below rated operation. These errors are likely related to inaccuracies in the generic controller simulated. Despite controller differences, FAST.Farm predicts the same overall relative rotor power trends for all waked turbines at all wind speeds.

17 WIND ENERGY↗

Multimodel validation of single wakes in neutral and stratified atmospheric conditions

Previous research has revealed the need for a validation study that considers several wake quantities and code types so that decisions on the trade-off between accuracy and computational cost can be well informed and appropriate to the intended application. In addition to guiding code choice and setup, rigorous model validation exercises are needed to identify weaknesses and strengths of specific models and guide future improvements. Here, we consider 13 approaches to simulating wakes observed with a nacelle-mounted lidar at the Scaled Wind Technology Facility (SWiFT) under varying atmospheric conditions. We find that some of the main challenges in wind turbine wake modeling are related to simulating the inflow. In the neutral benchmark, model performance tracked as expected with model fidelity, with large-eddy simulations performing the best. In the more challenging stable case, steady-state Reynolds-averaged Navier–Stokes simulations were found to outperform other model alternatives because they provide the ability to more easily prescribe noncanonical inflows and their low cost allows for simulations to be repeated as needed. Dynamic measurements were only available for the unstable benchmark at a single downstream distance. These dynamic analyses revealed that differences in the performance of time-stepping models come largely from differences in wake meandering. This highlights the need for more validation exercises that take into account wake dynamics and are able to identify where these differences come from: mesh setup, inflow, turbulence models, or wake-meandering parameterizations. In addition to model validation findings, we summarize lessons learned and provide recommendations for future benchmark exercises.

17 WIND ENERGY↗

OLAF User's Guide and Theory Manual

This report consists of the user's guild and theory manual for a newly-integrated free vortex wake method (OLAF) into OpenFAST. The report will serve as a reference for all pertinent theoretical information, as well as compilation/use instructions and best-practices for using the code.

16 TIDAL AND WAVE POWER↗

Sensitivity analysis of the effect of wind characteristics and turbine properties on wind turbine loads

Proper wind turbine design relies on the ability to accurately predict ultimate and fatigue loads of turbines. The load analysis process requires precise knowledge of the expected wind-inflow conditions as well as turbine structural and aerodynamic properties. However, uncertainty in most parameters is inevitable. It is therefore important to understand the impact such uncertainties have on the resulting loads. The goal of this work is to assess which input parameters have the greatest influence on turbine power, fatigue loads, and ultimate loads during normal turbine operation. An elementary effects sensitivity analysis is performed to identify the most sensitive parameters. Separate case studies are performed on (1) wind-inflow conditions and (2) turbine structural and aerodynamic properties, both cases using the National Renewable Energy Laboratory 5 MW baseline wind turbine. The Veers model was used to generate synthetic International Electrotechnical Commission (IEC) Kaimal turbulence spectrum inflow. The focus is on individual parameter sensitivity, though interactions between parameters are considered. The results of this work show that for wind-inflow conditions, turbulence in the primary wind direction and shear are the most sensitive parameters for turbine loads, which is expected. Secondary parameters of importance are identified as veer, u -direction integral length, and u components of the IEC coherence model, as well as the exponent. For the turbine properties, the most sensitive parameters are yaw misalignment and outboard lift coefficient distribution; secondary parameters of importance are inboard lift distribution, blade-twist distribution, and blade mass imbalance. This information can be used to help establish uncertainty bars around the predictions of engineering models during validation efforts, and provide insight to probabilistic design methods and site-suitability analyses.

17 WIND ENERGY↗

FAST.Farm Response to Varying Wind Inflow Techniques: Preprint

FAST.Farm is a newly developed multiphysics, midfidelity engineering tool that can be used to predict turbine power and structural loads of wind turbines in a wind farm. Previous studies have shown the similarities and differences between FAST.Farm and large-eddy simulations (LES) using the same LES-precursor-generated ambient wind inflow. The ability to generate ambient wind inflow using a synthetic turbulence engineering model (e.g., TurbSim or the Mann model) has recently been integrated into FAST.Farm to potentially enable more computationally efficient usage of the tool. This work aims to: 1) compare FAST.Farm simulations using LES-generated inflow to those using synthetically generated inflow from TurbSim, and 2) establish guidelines by which TurbSim-generated inflow should be generated for wind farm analysis. It was found that properly setting spatial coherence parameters for the transverse wind velocity components is necessary to accurately predict wake meandering. It is shown that TurbSim-generated inflow can be used in FAST.Farm to accurately predict thrust, power, speed, and torque for waked and unwaked turbines; wake meandering behavior across different atmospheric conditions; and averaged wake-deficit advection and evolution effects.

17 WIND ENERGY↗

Sensitivity of Uncertainty in Wind Characteristics and Wind Turbine Properties on Wind Turbine Extreme and Fatigue Loads

Wind turbine design relies on the ability to accurately predict turbine ultimate and fatigue loads. The loads analysis process requires precise knowledge of the expected wind-inflow conditions as well as turbine structural and aerodynamic properties. However, uncertainty in most parameters is inevitable. It is therefore important to understand the impact such uncertainties have on the resulting loads. The goal of this work is to assess which input parameters have the greatest influence on turbine power, fatigue loads, and ultimate loads during normal turbine operation. An Elementary Effects (EE) sensitivity analysis is performed to identify the most sensitive parameters. Separate case studies are performed on (1) wind-inflow conditions and (2) turbine structural and aerodynamic properties, both using the National Renewable Energy Laboratory (NREL) 5-MW baseline wind turbine. The focus is on individual parameter sensitivity, though interactions between parameters are considered.

17 WIND ENERGY↗

Assessment of Airfoil Property Sensitivity on Wind Turbine Extreme and Fatigue Loads: Preprint

Wind turbines are designed using a set of simulations to determine the structural loads that the turbine could experience. These structural loads can be significant influenced by physical turbine parameters. While significant research and effort has been put into measuring and defining such parameters, limited work has been done to quantify the sensitivity of structural loads to uncertainty in the physical turbine parameters. This paper therefore seeks to assess the sensitivity of different turbine aerodynamic parameters on the resulting ultimate and fatigue loads of the turbine during normal operational conditions. Eighteen different turbine parameters are screened using an Elementary Effects approach with radial points. The results show a high sensitivity of the loads to the blade twist and lift coefficient distributions. To a lesser extent, other turbine parameters that drive loads include the maximum lift coefficient location, blade chord length, and drag coefficient distributions.

17 WIND ENERGY↗

FAST.Farm Response to Varying Wind Inflow and Discretization

FAST.Farm is a newly developed multiphysics, midfidelity engineering tool that can be used to predict turbine power and structural loads of wind turbines in a wind farm. Previous studies have shown the similarities and differences between FAST.Farm and large-eddy simulations (LES) using the same LES-precursor-generated ambient wind inflow. The ability to generate ambient wind inflow using a synthetic turbulence engineering model (e.g., TurbSim or the Mann model) has recently been integrated into FAST.Farm to potentially enable more computationally efficient usage of the tool. This work aims to: 1) compare FAST.Farm simulations using LES-generated inflow to those using synthetically generated inflow from TurbSim, and 2) establish guidelines by which TurbSim-generated inflow should be generated for wind farm analysis. It was found that properly setting spatial coherence parameters for the transverse wind velocity components is necessary to accurately predict wake meandering. It is shown that TurbSim-generated inflow can be used in FAST.Farm to accurately predict thrust, power, speed, and torque for waked and unwaked turbines; wake meandering behavior across different atmospheric conditions; and averaged wake-deficit advection and evolution effects.

17 WIND ENERGY↗