Search NASA⌕ Search

Engineering topics

Silverstein, Joshua A.

Publications and source records attributed to Silverstein, Joshua A..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Pelletization with Spark Plasma Sintering and Characterization of Metal Iodides: An Assessment of Long-Term Radioiodine Immobilization Options

Four promising iodine “getter” materials (Ag, Cu, Bi, and Sn) for radioiodine capture were assessed in their pure metal-iodide (MI x ) pelletized forms to compare relative chemical durabilities. To study chemical durability, commercial MI x compounds of AgI, BiI 3 , BiOI, CuI, and SnI 4 were converted to dense monolithic pellets using spark plasma sintering. Semidynamic leach testing in the form of modified ASTM C1308 tests was then performed on the pellets in two different forms including unmounted (as-pressed) specimens (i.e., “U”) and epoxy-mounted specimens (i.e., “M”) with polished surfaces. The chemical durability results and sample characterizations showed that three of the five MI x compounds tested (i.e., AgI, CuI, and BiOI) displayed moderate to high leach resistances. Further, the remaining two MI x compounds (i.e., BiI 3 and SnI 4 ), which are both desirable iodine waste forms due to their high iodine loading capacities, readily decomposed during leach testing, indicated by crystallographic changes in the specimens as well as large amounts of iodine detected in the leachate solutions. The instabilities of BiI 3 and SnI 4 raise uncertainties for using the base metals/cations (i.e., Bi 0 /Bi 3+ and Sn 0 /Sn 4+ , respectively) as viable getters for radioiodine capture due to likely poor waste form chemical durabilities after capture and consolidation into waste forms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Preliminary Characterization and Evaluation on FFF Manufactured 316H and ODS Steels

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross-cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. The overarching vision of AMMT is to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy. Solid-state advanced manufacturing techniques can overcome some of the challenges in liquid-based additive manufacturing (AM) processes and should therefore be considered in material design and manufacturing as well. The work presented in this report forms part of a study on solid-state AM techniques of 316 stainless steels (SS) and oxide dispersion strengthened (ODS) steel components and supports the vision and goals of the AMMT program relevant to accelerate the development and deployment of advanced manufacturing processes. Achieving this can provide a safety improvement through larger safety margins, economic benefit for higher efficiency during operation, and a cost reduction through more effective manufacturing processes and less waste. This study provides preliminary information on development of the fused-filament fabrication (FFF) process using different powder types to demonstrate the sensitivity, and therefore the characterization of these sample components. The full solid-state manufacturing feasibility study will be completed and reported in a final feasibility evaluation during 2025. The study investigation used two 14YWT ODS powder batches, which provided information and the effect of different powder morphologies on manufacturability. The two 316SS powders demonstrated the effect of powder size on the manufacturability using FFF. Two product forms, namely a honeycomb structure and flat samples, were manufactured to demonstrate the flexibility of product form.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural evolution in shear-punch tests: A comparative study of pure Cu and Cu-Cr alloy

Understanding the mechanisms behind microstructural evolution during shear deformation has been a long-standing area of interest. However, establishing a connection between microstructure, mechanical properties, and extent of shear deformation is challenging and requires refined experimental approaches. Shear-punch testing (SPT) provides a controlled method to introduce shear into small volumes of material that later can be subjected to detailed microstructural characterization. In this study, we utilize an SPT device to induce shear deformation to pure copper and a binary copper-chromium alloy. Electron backscatter diffraction and transmission electron microscopy were used to study the mechanisms of plastic deformation after SPT. Our results indicate that shear deformation of pure Cu produces a dense network of intercepting microshear bands upon sustained deformation. Twin boundaries undergo degradation into high angle grain boundaries due to simultaneous deviation from the axis-angle pair condition of 60° misorientation on [111] direction. The presence of 50% volume Cr particles in the soft Cu matrix fundamentally altered the shear deformation mechanism. Preferential deformation of the Cu matrix led to accelerated shear-induced formation of low and high angle grain boundaries, and subsequent grain refinement. Comparatively, no grain refinement occurred in pure Cu at a strain ~10 times larger (ϵ = 4.73) than that of the copper-chromium case (ϵ = 0.42). Overall, our study sheds light on the microstructural evolution during shear deformation and highlights the significant influence of particle reinforcements on the shear deformation mechanisms of metals.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Formulation and testing of a high-tin borosilicate nuclear waste glass for in-can melting

Here, borosilicate waste glasses were successfully developed to immobilize two high-level waste raffinate streams via an in-can melter process with an Inconel 601 canister at 1050 °C. Measured viscosity and crystallinity thermal profiles were within the targeted processing constraints for the in-can melter process. Measured chemical durability of the glass by ASTM C1285–21 (Method A), ranged from normalized loss of boron, NL(B) = 1.44 – 2.65 g•m -2 , and NL(B) decreased with increased waste loading, accompanied by increased SnO 2 crystallinity. Measured corrosion of the in-can melter canister by a glass melt showed that Inconel 601 performed well at 1100 °C for up to 500 hr. Resistance polarization measurements versus time revealed that Inconel 601 corrosion rates in (and by) glass melts decreased from an initial rate of 63 mm•y -1 down to 10.2 mm•y -1 after 137 h with increased duration, which was attributed to formation of an oxide passivation layer (mainly Cr 2 O 3 ) at the alloy-glass interface.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Shear deformation of pure-Cu and Cu/Nb nano-laminates using micromechanical testing

Solid phase processing by introducing shear deformation into materials can result in unique microstructure evolution and enhanced mechanical properties, especially for immiscible systems such as Cu/Nb. To better understand the correlation between microstructure and deformation behavior during shear, a dedicated testing design of stress localization at predicted sites is necessary. In this study, a specialized S-shaped specimen geometry is implemented to apply localized simple-shear loading in pure-Cu and Cu/Nb accumulative roll-bonded nanolaminates. The nanoscale microstructure and proximity of interfaces in Cu/Nb offer a ~2.8-fold increase in shear stresses than pure-Cu. In pure-Cu, the plastic instability causes shear banding and an in-plane lattice rotation. In Cu/Nb, a partial bending of the interfaces occurred, resulting in a localized lattice rotation. The adapted geometry for micro-scale specimens thus successfully captures the shear deformation at predicted sites in two distinct material systems and could potentially be a powerful technique to study the deformation mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Temperature-dependent formation of gradient structures with anomalous hardening in an Al–Si alloy

The temperature effect on forming gradient structure in an Al-Si alloy during surface severe deformation is studied in this report. The intermediate temperature (473 K) produces the steepest gradient structure by an anomalous hardening on the top layer compared to lower (300 K) and higher temperature (673 K) counterparts. Our analysis shows profuse aluminum oxide particles in the top layer of the gradient structure under 473 K and thus lead to anomalous hardening by oxide-dispersion strengthening. Here, the counterintuitive enhancement of strengthening at the intermediate temperature is explained by the dynamic interplay between thermal-driven, mechanical-aided oxidation and the wear-induced loss of surface materials as a function of temperature, which yields a critical processing temperature to achieve the steepest gradient structure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Heterogenous activation of dynamic recrystallization and twinning during friction stir processing of a Cu-4Nb alloy

An interplay between high degree of shear deformation and deformation-induced heating occurs during friction stir processing (FSP) of metals. In medium-to-low stacking fault energy Cu alloys, this can lead to a complex spatially heterogenous activation of dynamic recrystallization (DRX) and twinning mechanisms. Within the Cu-Nb system, the presence of Nb is further expected to influence the DRX mechanism of the Cu matrix. However, the microstructural changes induced by the co-deformation of Nb during FSP are still not well understood. So, this study uses a combination of multimodal microstructural characterization, solution thermodynamics-based predictions, and computational crystal plasticity simulation to reveal the various microstructural evolution mechanisms that can occur during FSP of a Cu-4at.%Nb binary model alloy. The formation of softer DRX zones, and harder shear localization regions are revealed using electron backscatter diffraction, transmission electron microscopy, atom probe tomography, and crystal plasticity modeling.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Friction-based riveting technique for AZ31 magnesium alloy

Rivet materials used in the aerospace and automotive industries are typically alloys of aluminum (Al) or steel. Magnesium (Mg) is an attractive alternative because it is 33% and 75% lighter than Al and steel, respectively. However, a primary barrier for using Mg as rivet material is its poor formability at room temperature, resulting in brittle fracture of the rivet head during cold riveting. Hot riveting is possible but suffers from high cycle time due to the need for pre-heating. A new friction-based riveting technique, Rotating Hammer Riveting (RHR), is reported to fully form AZ31 Mg rivet heads in a mere 0.23 seconds cycle time. Heat and pressure generated through severe plastic deformation during the process was sufficient to form the Mg rivet head without the need for a separate pre-heating operation. Due to dynamic recrystallization, AZ31 Mg grains in the rivet head were significantly refined from about 15 to 2.6 µm during RHR, which favors the formability of Mg rivet by triggering grain boundary sliding and reducing plastic anisotropy of Mg. In addition, RHR joints showed a metallurgical bond between the rivet head and top sheet, which eliminates a significant pathway for corrosion.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Decoupling of strain and temperature effects on microstructural evolution during high shear strain deformation

The interplay between defect generation by shear strain and defect annihilation by local heating is difficult to predict in shear-assisted processing techniques. In this study, we decoupled the effects of high shear strain and external heating in an immiscible Cu-Nb alloy using a pin-on-disk tribometer to mimic the microstructural evolution of material during solid-phase processing. The change in sub-surface deformation, strain distribution, and redistribution of the second phase as a function of temperature were examined using transmission electron microscopy and atom probe tomography. Zener-Hollomon parameter is used to semi-quantify the deformation of Cu-Nb alloys as a function of strain and temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermal Stability and Mechanical Properties of Cold-Sprayed Nickel-Yttria Coating

The microstructural evolution under the extreme environments imposed during cold spray deposition of cermet coatings and the microstructural recovery during post-processing annealing treatments is rather complex and not well understood. Here, Ni-Yttria cermet coatings on an SS304 substrate were produced using cold spray technique, resulting in a bimodal grain structure. The grain growth, phase stability, hardness, and wear properties are observed in as-deposited and annealed (at 400 °C) Ni-Yttria and pure Ni coatings. A multimodal microstructural characterization using electron microscopy, and atom probe tomography shows the structural and compositional stability of yttria particles and Ni grains. A fragmentation of Y-rich particles and dispersion in Ni was observed, however, no forced mixing/dissolution of Y in Ni is detected. Nano-yttria dispersed within the Ni grains slowed the grain growth during annealing. After annealing, Yttria reinforced coating was 1.5 times harder and showed better thermal and mechanical stability compared to the Ni coating.

Gwalani, Bharat↗
DOE OSTI2022

A Finite Difference Analysis of the Effect of Graphene Additions on the Electrical Conductivity of Polycrystalline Copper

A finite-difference method was used to explore the effect of graphene on the bulk electrical conductivity of copper-graphene composites. In this capacity, grain orientation information from pure copper and copper-graphene composites were used to generate synthetic 3D microstructures. The electrical conductivity of these microstructures were calculated using the finite difference method assuming different average grain sizes. From these calculations, we demonstrate that when high-conductivity grain boundaries are present within the microstructure arising from the presence of graphene, an increase in the bulk electrical conductivity is observed. On the other hand, the difference in textures between copper and copper-graphene composites may not account for a significant difference in bulk electrical conductivity. In comparison, the copper grain size has a considerably larger effect on electrical conductivity as previously anticipated. This is one of the first demonstrations of a physical basis for enhanced conductivity composites and presents pathways for further investigations on the effects of composite microstructural features, material interfaces and graphene content on electrical performance.

Frazier, William E.↗
DOE OSTI2021

Extrusion of Unhomogenized Castings of 7075 Aluminum via ShAPE

Extrusion of unhomogenized castings of 7075 aluminum (Al) alloy has been accomplished using shear assisted processing and extrusion (ShAPE). The simultaneous plastic deformation and heat generation during ShAPE rapidly fracture and dissolve interdendritic and intragranular secondary phases of Al-Zn-Mg-Cu, accomplishing homogenization in seconds rather than many hours in a furnace prior to extrusion. ShAPE thereby eliminates the energy-intensive and time-consuming homogenization step required to prepare as-cast microstructures for conventional extrusion. Concurrently, extensive grain refinement occurs due to gradient activation of dynamic recrystallization during ShAPE, which facilitates a threefold increase in extrusion speed compared to the conventional extrusion method. Evident enhancement of the mechanical properties of ShAPE+T6 samples is achieved, compared to the ASTM standard values for conventional extrusion products. The microstructural evolution pathway, involving the processes of grain refinement and secondary particle dissolution, is explained using scanning and transmission electron microscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Multimodal Analysis of Spatially Heterogeneous Microstructural Refinement and Softening Mechanisms in Three-Pass Friction Stir Processed Al4Si Alloy

Multiple thermally and thermomechanically induced microstructural refinement mechanisms can be activated in metallic alloys when subjected to solid phase processing methods such as friction stir processing (FSP). In this work, we provide detailed descriptions of the relationship between region-specific microstructural refinement mechanisms and the variation in microhardness, through a systematic and multimodal microstructural characterization of an FSP-processed 75% cold-rolled Al-4 at.% Si model binary alloy. Spatially resolved high-energy synchrotron X-ray diffraction, electron backscattered diffraction, and scanning transmission electron microscopy were used to understand the spatially heterogeneous microstructural evolution due to FSP. Results provide insights into how mechanisms such as static recovery, static recrystallization, dynamic recovery and recrystallization, geometric and continuous dynamic recrystallization, and particle-stimulated static or dynamic grain nucleation may occur heterogeneously in the microstructure as a function of the distance from the stir zone in processed alloys, directly influencing the degree of softening. The systematic analysis of microstructures and hardness in the FSP-processed model binary alloy given in this work highlights the rich microstructural domains that can be uniquely harnessed through solid phase processing of metallic alloys.

Al4Si, Friction Stir Processing, Geometric Dynamic↗
DOE OSTI2021

The Influence of Transitional Metal Dopants on Reducing Chlorine Evolution during the Electrolysis of Raw Seawater

Electrocatalytic water splitting is a possible route to the expanded generation of green hydrogen; however, a long-term challenge is the requirement of fresh water as an electrolyzer feed. The use of seawater as a direct feed for electrolytic hydrogen production would alleviate fresh water needs and potentially open an avenue for locally generated hydrogen from marine hydrokinetic or off-shore power sources. One environmental limitation to seawater electrolysis is the generation of chlorine as a competitive anodic reaction. This work evaluates transition metal (W, Co, Fe, Sn, and Ru) doping of Mn-Mo-based catalysts as a strategy to suppress chlorine evolution while sustaining catalytic efficiency. Electrochemical evaluations in neutral chloride solution and raw seawater showed the promise of a novel Mn-Mo-Ru electrode system for oxygen evolution efficiency and enhanced catalytic activity. Subsequent stability testing in a flowing raw seawater flume highlighted the need for improved catalyst stability for long-term applications of Mn-Mo-Ru catalysts. This work highlights that elements known to be selective toward chlorine evolution in simple oxide form (e.g., RuO2) may display different trends in selectivity when used as isolated dopants, where Ru suppressed chlorine evolution in Mn-based catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Shear Assisted Processing and Extrusion (ShAPE) of Aluminum Alloy 7075, 2024, and Al-12.4TM

The most common aluminum alloys utilized in the aerospace industry are 7075 and 2024 due to their high strength-to-weight ratio compared to advanced high strength steels and other aluminum alloys. Despite excellent performance, these aluminum alloys have seen limited use outside of the aerospace industry due in part to high cost. If high-performance aluminum extrusions could be made more cost effectively by eliminating energy intensive process steps typical of conventional extrusion, then numerous opportunities exist for more widespread adoption. A key reason for the high cost of 7075 and 2024 extrusions (25-75% higher than 6061) is their slow extrusion speed. 7075 and 2024 are limited to 2 m/min and 3.5 m/min respectively, in contrast to 6061 which can be extruded at 20–80 m/min. In addition to slow speed, aluminum alloys require numerous thermal treatments throughout the extrusion process including homogenization and pre-heating prior to extrusion, and solution heat treating and artificial aging after extrusion. Each of these steps contribute to the total energy consumed during manufacturing of extruded components. This project investigates the use of ShAPE to improve extrusion speed and reduce, or even eliminate, the typical thermal treatments for high strength aluminum alloys, all while improving material performance. The overarching goal of this project was to demonstrate that Shear Assisted Processing and Extrusion (ShAPE) can manufacture high-performance aluminum alloy tubing with lower manufacturing energy and improved mechanical properties compared to conventional extrusion. Unlike conventional extrusion where the billet is rammed against a stationary die using a strictly linear motion, the ShAPE process superimposes a rotational shear force by spinning the die while the billet is plunged. Compared to conventional linear extrusion, the ShAPE process imparts significantly more strain into the feedstock material, which enables the formation of novel microstructures. These microstructures manifest an array of property and process improvements for extrusion of high-performance aluminum alloys. The following accomplishments were achieved for this project: Extrusion of 7075 at 12.2 meters/min compared to 2 meters/min for conventional extrusion; Elimination of 7075 billet homogenization (430 °C for 20 hours) which is required prior to conventional extrusion; Elimination of 7075 billet pre-heating (400 °C for 1 hour) in a separate furnace which is required prior to conventional extrusion; Achieved 7075-T6with yield strength = 595 MPa, ultimate tensile strength = 531MPa, and elongation = 17.4% for extrusions made from unhomogenized billets. Exceeds the ASTM and ASM standard, and typical industry values; Achieved 7075-T5 (i.e., no solution heat treatment) with yield strength = 588 MPa, ultimate tensile strength = 535 MPa, and elongation = 14.8% for extrusions made from homogenized billets; Extrusion of 2024 at 7.4 meters/min compared to 3.5 meters/min for conventional extrusion; Achieved 2024-T8510 yield strength = 522 MPa, ultimate strength = 510MPa, and elongation = 7.1% for extrusions made from wrought billets. Exceeds the ASTM and ASM standard, and typical industry values; Extrusion of Al-12.4TM high-performance aluminum powder directly into tubing, in a single step, which eliminates process steps typical of powder metallurgy extrusion.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mica filled polyetherketoneketones for material extrusion 3D printing

Polyetherketoneketone (PEKK) has superior physical properties to most available thermoplastics compatible with material extrusion-based 3D printing, including analogs in the polyaryletherketone (PAEK) family. To date, the performance of fused filament fabrication (FFF) compatible PEKK has been detailed primarily as a function of varying the isomer ratios composing the co-polymer structure. The strategy to form blends or composites with PEKK for FFF is attractive for further tailoring of performance in application, yet has received limited attention. Here, we report the integration of three grades of mica platelets into PEKK at 10% and 30% mass loadings to generate an array of filament feedstocks that were then used to print objects with a simple FFF machine. The effects of mica coating chemistry and surface treatment on the compatibility with PEKK and resulting properties are described. Mica fillers at both loadings have only subtle influence on the FFF relevant melt rheological properties inherent to PEKK. Pigment micas at high loadings can lower the melting temperature of PEKK (up to 19 ºC) without shifting its glass transition temperature and inhibit much of the undesirable crystallization occurring during processing with unfilled PEKK. The printed composites were effectively cold crystallized post-printing, affording crystalline fractions up to 90% relative to unfilled PEKK with increased dimensional stabilities. All micas, when used as fillers in low and high relative PEKK crystallinities, significantly increased the tensile modulus (as high as 126% or to 7.31 GPa) of parts in correlation to the loading. Furthermore, the underlying microstructural features of a printed composite were compared to unfilled PEKK by use of a high-resolution helical micro-computed tomography instrument. Practically, pigment micas can confer a wide range of rich colors to 3D-printed PEKK.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Bismuth-Functionalized Silica Aerogels for Iodine Capture

The U.S. Department of Energy is looking into alternative sorbents for the removal of radioiodine from off-gas streams in a used nuclear fuel reprocessing plant. One class of sorbents considered are bismuth-functionalized silica aerogels which offer an efficient capture of iodine from off-gas streams and are environmentally friendly and lower cost when compared to silver-functionalized sorbents. Two types of bismuth-functionalized silica aerogels were successfully manufactured using a hierarchical synthesis approach:1) The Bi 3+ -aerogel with bismuth oxide nitrate hydroxide hydrate particles and 2) Bi-aerogel with bismuth metal and bismuth sulfide nanoparticles. Both sorbents exhibited high sorption capacity for iodine. However, presence of particles of different composition, size, and distribution on aerogel support resulted in different iodine loadings. The Bi 3+ -aerogel exhibited sorption capacity of 289 mg/g. In contrast, Bi-aerogel exhibited more that 20% higher sorption capacity. The heat-treatment of Bi 3+ -aerogel at 225? under hydrogen atmosphere increased iodine loading capacity to 351 mg/g.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗