Search NASA⌕ Search

Engineering topics

Silverstein, Joshua A.

Publications and source records attributed to Silverstein, Joshua A..

26 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Lattice misorientation evolution and grain refinement in Al-Si alloys under high-strain shear deformation

The starting microstructure of an alloy can be tailored to achieve varying degrees of microstructural refinement and enhance mechanical properties through severe plastic shear deformation during solid-phase processing. Crystal plasticity-based grain misorientation modeling, coupled with systematic pin-on-disk tribometry-based subsurface shear deformation experiments on as-cast Al-xSi alloys (x = 0, 1, 4 at %), was conducted. The post-deformation microstructural analysis, through a combined computational and experimental approach, conclusively shows that the initial volume fraction of the hard Si phase enhances the evolution of local lattice misorientation, leading to efficient grain refinement during severe plastic shear deformation. The shear–deformation-induced nanostructure resulted in more than double the nanoindentation hardness in the processed alloy.

Gwalani, Bharat↗
DOE OSTI2021

Low-Activity Waste Glass Standards Preparation and Characterization for Calibration of Analytical Instruments

A matrix of seven low-activity waste (LAW) glasses was fabricated and characterized to be used by the Hanford Waste Treatment and Immobilization Plant (WTP) as analytical instrument calibration and matrix interference standards when measuring LAW glass compositions. The matrix of glasses was designed to represent the range of LAW glass compositions that will be generated by the WTP. Samples from each of the seven glasses were measured with electron probe microanalysis (EPMA), ion chromatography (IC), and bulk inductively coupled plasma mass spectroscopy (ICP-MS) to determine the variability and accuracy across batches and within individually poured glass bar samples. High relative percent differences and standard deviations were calculated for components with low concentrations due to instrument detection limits. IC and ICP-MS percent differences and standard deviations were higher at low component concentrations. Otherwise, variability in measured compositions from IC and ICP-MS was generally lower than measurements from EPMA, with the exclusion of Cl, F, Si, and B. Overall, the two methods proved comparable and complementary. From EPMA, IC, and ICP-MS data, volatile elements were underrepresented compared to batched compositions, which suggested loss of these elements during melting. EPMA data was statistically analyzed to evaluate homogeneity within single bars and whole compositions for each of the seven glasses. Most of the variability within glass compositions occurred at the bar-to-bar level; however, no clear systematic trends were observed. Based on these analyses, when using these glasses as reference material, it is recommended that the overall mean and variance of each composition be used for performing instrument calibrations and analytical corrections.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Process Robustness of Friction Stir Dovetailing of AA7099 to Steel with In Situ AA6061 Interlayer Linking

Rolled homogeneous armor (RHA) steel was joined to aluminum alloy AA7099-T7451 with an interlayer of AA6061-T651 by single-pass friction stir dovetailing (FSD). The evolution of the AA7099/AA6061 and AA6061/steel interfacial microstructures and mechanical properties of the joints were examined. The AA6061 interlayer prevented Zn migration from the AA7099 to the steel during FSD and inhibited formation of brittle, Zn-rich, Fe-Al intermetallic compounds within the joint. The flow of the dissimilar aluminum alloys at the interface was controlled with a partially threaded friction stir welding pin and a dovetail geometric configuration optimized in previous work. The process robustness was explored to establish parameter windows by elucidating parametric effects on the relationship between process conditions and the joint’s microstructure and mechanical properties. Ranges of process forge force (50–70 kN) and interface temperature (475°C–515°C) consistently yielded joints with adequate performance. The load-carrying capacity in lap shear tensile tests was 2025 ? 100 N/mm.

Friction Stir Dovetailing, FSW, AA7099, AA6061, Ro↗
DOE OSTI2020

Process Intensification for Nanocomposite Aluminum Extrusions: CRADA 411 (Final Report)

The project evaluated the feasibility of using Shear Assisted Processing and Extrusion (ShAPE) for the fabrication of extrusions with a diameter of 0.5” and higher from an Al-alloy powder feedstock that contains nanoscale second phases for achieving enhanced elevated temperature strength. PNNL has previously extruded 0.2” diameter rods with high strength aluminum alloy powder Al-12.4TM. This project aimed to scale the process up to a diameter of 1.0” at a length of >24” while retaining the excellent mechanical properties achieved for the 0.2” diameter rods. As part of the project, extrusion dies were fabricated with various design features. As an example, scroll features on the tool die face was introduced to enhance powder mixing, and reduce extrusion load. Varying extrusion ratios were used to obtain better microstructural homogeneity. Use of tool design features together with the optimization of process parameters helped in the fabrication of extrusions that were up to 48” long with a diameter of 0.5” using Al-12.4 TM powder feedstock in a two-step process involving cold compaction followed by extrusion. Extrusions with a diameter of 1.0” could also be fabricated, but limitations on the extent of consolidation were experienced as a result of the torque and ram force capacity of the current ShAPE machine.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Development and Characterization of Cementitious Waste Forms for Immobilization of Granular Activated Carbon, Silver Mordenite, and HEPA Filter Media Solid Secondary Waste

At the Department of Energy’s Hanford site, over 53 million gallons of chemically complex and radioactive wastes have been stored in 177 underground tanks. The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is under construction and is designed to treat and immobilize these wastes. During operations of WTP, solid secondary wastes (SSWs) will be generated as a result of waste treatment, vitrification, off-gas management, and supporting process activities. SSW treatment processes and resulting disposal pathways for the final disposition form of the SSW are needed to support direct feed low activity waste (DFLAW) operations and facilitate continued operation of WTP. The SSWs produced through WTP operations are expected to include used process equipment, contaminated tools and instruments, decontamination wastes, high-efficiency particulate air (HEPA) filters, carbon absorption beds (granular activated carbon, GAC), silver mordenite (AgM) and spent ion-exchange resins. These waste streams are planned to be immobilized in a cementitious waste form and disposed of either as stabilized/blended (non-debris) or encapsulated (debris) in a cementitious waste form. Accordingly, cementitious waste forms from these streams were included in the 2017 Integrated Disposal Facility (IDF) Performance Assessment (PA). The input data used to represent these SSW forms in the 2017 IDF PA involved many assumptions and associated uncertainties. This data limitation was due to the lack of material- and site-specific data available for representative SSW materials in cementitious matrices. To verify the assumed values used in the IDF PA and fill this limitation in available data, Washington River Protection Solutions, LLC (WRPS), has initiated a program targeted toward gathering site specific data relevant to Hanford SSW disposal. The work within this report is a continuation of this ongoing program.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Thermal Properties of Sodium Borosilicate Glasses as a Function of Sulfur Content

SO3 additions, up to 3.0 wt%, were systematically investigated for effects on the physical properties of sodium borosilicate glass melted in air, with a sulfur-free composition of 50SiO2-10Al2O3-12B2O3-21Na2O-7CaO (wt%). Solubility measurements, using electron microscopy chemical analysis, determined the maximum loading to be ~1.5 wt% SO3. It was found that sulfur (here as sulfate) in this glass increased the glass transition temperature, thermal diffusivity, heat capacity, and thermal conductivity, and decreased the mass density. Structural analysis, performed with Raman spectroscopy, indicated that the borosilicate network polymerized with sulfur additions, presumably due to Na2O being required to charge compensate the ionic SO42- additions, thus becoming unavailable to form non-bridging oxygen in the silicate network. It is postulated that this increased crosslinking of the borosilicate backbone lead to a structure with higher dimensionality and average bond energy. This increased the mean free paths and vibration frequency of the phonons, which resulted in the observed increase in thermal properties.

Thermal properties, Borosilicate glass, Sulfur sol↗