Search NASA⌕ Search

Engineering topics

Simon, John

Publications and source records attributed to Simon, John.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

24% Single-Junction GaAs Solar Cell Grown Directly on Growth-Planarized Facets Using Hydride Vapor Phase Epitaxy

A 24%-efficient single-junction GaAs solar cell grown directly on a faceted, spalled (100) GaAs substrate after in situ planarization growth by hydride vapor phase epitaxy (HVPE) is achieved. Controlled spalling, a promising low-cost substrate reuse technique, produces large facets in (100)-oriented GaAs substrates due to the orientation of the fracture planes used for lift-off. Planarization by HVPE offers a path toward direct use of these spalled substrates without costly polishing steps. In this report the growth rate anisotropy enabling planarization arising from diffusion and differences in the adsorption of growth species on {n11}B-type facets relative to (100) is determined. Consecutive planarization and device growth that results in a solar cell with a minimal performance difference relative to a control cell grown on an epitaxy-ready substrate are demonstrated. These results show that controlled spalling coupled with HVPE planarization is a viable pathway for lowering the cost of III-V photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2023

Light-trapping structures fabricated in situ for ultrathin III-V solar cells

Here, we describe a fully in situ method of fabricating light-scattering structures on III-V materials that generates a rough morphology via vapor phase etching and redeposition. Fully in situ methods support higher industrial throughput by utilizing the growth reactor to generate the light-trapping structures after device growth without removal from the reactor. We use HCl and PH 3 to etch and redeposit scattering morphologies on Ga 0.5 In 0.5 P in a dynamic hydride vapor phase epitaxy (D-HVPE) reactor. We show that the addition of PH 3 leads to redeposition during the vapor phase HCl etching of Ga 0.5 In 0.5 P and that HCl flow rate and time exposed to HCl-PH 3 each independently cause a linear increase in the redeposited feature size, indicating that redeposition proceeds by island growth in a III-Cl-limited, hydride-enhanced HVPE regime. Auger electron spectroscopy and scanning transmission electron microscopy with energy dispersive spectroscopy (STEM-EDS) reveal redeposition to be highly Ga-rich GaInP, i.e., Ga(In)P. The Ga-rich nature of the redeposition results from the higher thermodynamic driving force for Ga incorporation than for In during HVPE growth and the difference in the volatility of the III-Cl etch products. The resulting morphologies have high broadband scattering, as determined by normal specular reflectance and integrating sphere measurements, indicating effectiveness as light-scattering structures. In a 270-nm-thick GaAs photovoltaic device with a textured back surface, we achieve a 4.9% increase in short circuit current density (J SC ) without any loss in open-circuit voltage (V OC ) relative to a planar control using only a 60 s in situ texturing treatment.

14 SOLAR ENERGY↗
DOE OSTI2023

Modeling and design of III-V heterojunction solar cells for enhanced performance

Heterojunctions can increase the efficiency of solar cell devices relative to homojunctions, but there is a large parameter space with significant tradeoffs that must be considered. Here, we present an experimental and computational study of III-V heterojunction solar cells and show how the emitter doping, emitter band gap, and heteroband offsets impact device efficiency. Efficiency is maximized by pushing the junction depletion region into the wider band gap material while minimizing the effects of heteroband offsets through optimized choice of emitter band gap, emitter electron affinity, and/or emitter doping density. We use these results to guide optimization of devices grown by halide vapor phase epitaxy, achieving 27% efficiency in a GaAs/GaInPAs heterojunction device. We also show that heterojunctions yield proportionally larger efficiency improvements in lower-quality materials. Although the modeling was developed and validated using III-V materials, the results are theoretically applicable to materials systems outside III-Vs.

14 SOLAR ENERGY↗
DOE OSTI2023

Design of Planarizing Growth Conditions on Unpolished and Faceted (100)-Oriented GaAs Substrates Using Hydride Vapor Phase Epitaxy

Here we performed a design of experiments (DoE) analysis to determine the effect of various growth parameters on in situ planarizing overgrowth of rough substrates using hydride vapor phase epitaxy (HVPE). We used two types of rough (100)-oriented GaAs substrates to compare the effect of the initial morphology on the epitaxial growth behavior: an irregular, as-cut surface resultant from cutting the wafer from a GaAs boule and a regularly faceted surface produced by controlled spalling. The DoE analysis identified trends in the overgrowth behavior with changing growth conditions, and we used these trends to design favorable planarization growth conditions for each surface type. These favorable conditions enabled full planarization of a spalled surface with >2.5 um facet height within 10.8 min of growth. The root mean squared (RMS) surface roughness of the resulting (100) surface was 24.5 nm over a 286 um x 215 um area. Our results show that planarization growth by HVPE is a promising technique to enable device growth directly on rough substrates, and the trends revealed through DoE analysis indicate a path toward further optimization of planarization growth conditions for as-cut and spalled surfaces.

14 SOLAR ENERGY↗
DOE OSTI2022

AlInP-passivated III–V solar cells grown by dynamic hydride vapor-phase epitaxy

We report the development of AlInP-passivated solar cells grown by dynamic hydride vapor-phase epitaxy (D-HVPE) with AM1.5G efficiencies of 26.0% for single-junction (1J) GaAs cells and 28.0% for GaInP/GaAs (2J) tandems. We compare the device performance of solar cells passivated with AlInP versus control cells passivated with GaInP, which has already enabled near-unity carrier collection in GaAs solar cells. 1J devices passivated with either AlInP or GaInP have an identical open-circuit voltage (V OC ) of 1.06 V and long-wavelength current collection near 95%, indicating that both window materials provide a similar degree of passivation. Adding AlInP passivation to each solar cell structure improves the current collection by 1.3 and 1 mA/cm 2 for the 1J and 2J, respectively. The AlInP also results in a top cell V OC boost of ~40 mV relative to a tandem device passivated only by a thin, highly doped GaInP emitter. Secondary-ion mass spectrometry measurements indicate that although O and Si both incorporate in the AlInP window, they do not appear in the subsequently grown absorber layers and do not impact its ability to passivate the front surface. We expect that these achievements, along with continued optimization, will enable parity of hydride vapor-phase epitaxy (HVPE)-grown device efficiencies with state-of-the-art devices grown by other epitaxial methods in the near future.

14 SOLAR ENERGY↗
DOE OSTI2021

Performance of III–V Solar Cells Grown on Reformed Mesoporous Ge Templates

We demonstrate a solar cell on reformed porous Ge with an efficiency of 7.7%. We generate mesopores in (100) Ge by bipolar electrochemical etching and anneal them at high temperature. The pores coalesce deep in the structure rather than at the surface as desired, although resulting in coarse superficial morphology unsuitable for device growth. To combat this issue, we developed a surface treatment involving an HBr dip, annealing at 415 degrees C, and a postannealing ultrasonic De-ionized water dip to improve the surface structure, resulting in a smoother reformed surface on which we grow a GaInAs solar cell. The structure retains embedded pores after growth and the transitions between Ge and III-V layers are distinct. The solar cell fabricated using the improved coalescence has an efficiency of 4.5%. The efficiency improves to 7.7% by isolating the rest of the device from three limiting localized shunt areas. Protruding defects in the porous Ge and III-V layers still limit the performance, but this work establishes a step toward the technical viability of this exfoliation approach, showing decent efficiency if protruding defects can be removed or reduced.

14 SOLAR ENERGY↗
DOE OSTI2021

Radiation Effects in III-V Solar Cells Grown by Dynamic Hydride Vapor Phase Epitaxy

The recent development of hydride vapor phase epitaxy (HVPE) is potentially promising as a route to lower the cost of high-efficiency III-V solar cells for space applications. HVPE produces the same materials and device structures as the industry-standard organometallic vapor phase epitaxy (OMVPE) process, and although HVPE has shown promising device efficiencies, it lags the OMVPE growth technique in technical maturity. For example, there are no reports of the performance of HVPE-grown devices in radiation environments. There is an expectation that high-quality (that is, single crystal and low-defect) III-V materials will behave similarly regardless of the growth method. However, it is important to verify assumptions as facts. In this project, we produced materials and devices using both HVPE and OMVPE at NREL and irradiated them using 1 MeV electrons to ascertain the effect of radiation on the materials. We also performed initial work on producing more radiation-hard structures, including devices with the pn junction at the front of the device, and devices with a graded doping profile, both of which help with radiation tolerance. Measurements of the devices post radiation exposure showed that the open-circuit voltage (V OC ) of the HVPE-grown solar cells degraded least on a percent basis, although they also started from a lower baseline than the OMVPE-grown devices. All solar cells reached approximately the same V OC after irradiation, indicating that the dose used was sufficient to degrade all device equally. The short-circuit current in the HVPE devices did degrade more than the other solar cells, and this was attributed to a higher-than-expected doping density in the base layer of that cell. The results of these experiments, while by no means comprehensive, do not show any material difference in the radiation effects in OMVPE- and HVPE-grown materials and devices.

14 SOLAR ENERGY↗
DOE OSTI2021

Surface chemistry models for GaAs epitaxial growth and hydride cracking using reacting flow simulations

Hydride vapor phase epitaxy (HVPE) is a promising technology that can aid in the cost reduction of III-V materials and devices manufacturing, particularly high-efficiency solar cells for space and terrestrial applications. However, recent demonstrations of ultrafast growth rates (~500 µm/h) via uncracked hydrides are not well described by present models for the growth. Therefore, it is necessary to understand the kinetics of the growth process and its coupling with transport phenomena, so as to enable fast and uniform epitaxial growth. In this work, we derive a kinetic model using experimental data and integrate it into a computational fluid dynamics simulation of an HVPE growth reactor. We also modify an existing hydride cracking model that we validate against numerical simulations and experimental data. Here, we show that the developed growth model and the improved cracking model are able to reproduce experimental growth measurements of GaAs in an existing HVPE system.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS↗
DOE OSTI2021

Inverted metamorphic GaInAs solar cell grown by dynamic hydride vapor phase epitaxy

We present an inverted metamorphic rear heterojunction ~1.0 eV GaInAs solar cell deposited by dynamic hydride vapor phase epitaxy (D-HVPE) with high growth rate. This device uses a Ga 1-x In x P compositionally graded buffer (CGB) to bridge the lattice constant gap between the GaAs substrate and the Ga0.71In0.29As emitter layer. High-resolution x-ray diffraction and transmission electron microscopy confirm that the Ga 0.71 In 0.29 As emitter is grown lattice-matched to the in-plane lattice constant of the CGB with minimal generation of defects at the GaInAs/GaInP interface. The device contains a threading dislocation density of 2.3 × 10 6 cm -2 , a level that enables high-performance minority carrier devices and is comparable to previously demonstrated GaInP CGBs grown by D-HVPE. The device exhibits an open-circuit voltage of 0.589 V under a one-sun AM1.5G illumination condition and a bandgap-voltage offset of 0.407 V, indicating metamorphic epitaxial performance nearly equal to state-of-the-art devices. We analyze the dark current of the device and determine that reducing recombination in the depletion region, which can be achieved by reducing the threading dislocation density and optimizing the device doping density, will improve the device performance. Furthermore, the CGB and device layers, comprising ~8 µm of thickness, are grown in under 10 min, highlighting the ability of D-HVPE to produce high-quality metamorphic devices of all types with the potential for dramatically higher throughput compared to present technology.

14 SOLAR ENERGY↗
DOE OSTI2021

Dopant Diffusion Control for Improved Tandem Cells Grown by D-HVPE

GaInP top cell current-density presently limits the performance of HVPE-grown two-junction devices, in large part due to unwanted dopant diffusion. Here, we institute mitigation strategies to lower the diffusion of dopants from both the front contact and back surface field. Successful application of these strategies resulted in a short-circuit current density of 12.1 mA/cm 2 in a GaInP/GaAs cell, an improvement of 0.9 mA/cm2 over our previous best cell. The reduced Se diffusion results in a thinner unpassivated emitter, which can lead to higher series resistance. Despite the increased resistance we obtained an efficiency increase from 23.7% to 24.8%.

42 ENGINEERING↗
DOE OSTI2021

Control of Surface Morphology during the Growth of (110)-Oriented GaAs by Hydride Vapor Phase Epitaxy

We present a study of the effect of hydride vapor phase epitaxy (HVPE) growth conditions on the morphology of GaAs grown on vicinal and nominally exact (110) GaAs substrates. We evaluate epilayer surfaces using a combination of Nomarski microscopy and atomic force microscopy. The surface morphology strongly depends on the growth conditions employed, as well as the substrate orientation. On substrates offcut 3° toward (111)A, faceting generally develops under conditions in which the growth is Ga-limited, although Ga-limited growth is not the only requirement for faceting. Low growth temperatures lead to a faceted morphology, while higher growth temperatures favor smooth growth and facet-free morphology. We show that the surface morphology is kinetically controlled and that the tendency to facet correlates with the growth rate. 3D growth occurs on nominally exact substrates, resulting in hillock formation, but reduction of the group V precursor partial pressure results in smooth morphology. Overall, our results are consistent with models for step-bunching-induced surface faceting that invoke a negative Ehrlich–Schwoebel step-edge barrier.

(110) oriented GaAs↗
DOE OSTI2021

Compositionally graded Ga 1-x In x P buffers grown by static and dynamic hydride vapor phase epitaxy at rates up to 1 μm/min

Here, we demonstrate Ga 1-x In x P compositionally graded buffers (CGBs) grown on GaAs with lattice constants between GaAs and InP by hydride vapor phase epitaxy (HVPE). Growth rates were up to ~1 μm/min and threading dislocation density (TDD) was as low as 1.0 x 10 6 cm -2 . We studied the effect of substrate offcut direction, growth rate, and strain grading rate on CGB defect structure. We compared the effect of a “dynamic grading” style, which creates compositional interfaces via mechanical transfer of a substrate between two growth chambers, vs. “static grading” where the CGB grows in a single chamber. Dynamic grading yielded smoother grades with higher relaxation, but TDD was not significantly different between the two styles. Substrate offcut direction was the most important factor for obtaining CGBs with low defect density. (001) substrates offcut towards (111)B yielded smoother CGBs with lower TDD compared to CGBs grown on substrates offcut towards (111)A. Transmission electron microscopy of static and dynamic CGBs grown on A and B-offcuts only found evidence of phase separation in a static A-offcut CGB, indicating that the B offcut limits phase separation, which in turn keeps TDD low. Reduced growth rate led to the appearance CuPt-type atomic ordering, which affected the distribution of dislocations on the active glide planes but did not alter TDD. Higher growth rates led to smoother CGBs and did not appreciably increase TDD as otherwise predicted by steady-state models of plastic relaxation. These results show HVPE’s promise for lattice-mismatched applications and low-c ost InP virtual substrates on GaAs

36 MATERIALS SCIENCE↗
DOE OSTI2021

GaAs Solar Cells Grown on Intentionally-Contaminated GaAs Substrates

III-V solar cells have the best performance of any semiconductor materials, but deposition of these materials relies on high-quality single crystal GaAs wafers for their superior performance. Unfortunately, the cost of these wafers makes these high-efficiency devices only accessible in high-value or niche markets. Here, we explored the effect of growing bulk GaAs crystals with lower purity input materials in order to reduce their cost. We observe that intentional impurities added to the melt before the crystal growth occurs segregate to the top of the boule. Single junction GaAs solar cells grown on wafers made from contaminated boules showed no performance degradation compared to a high-purity control wafer. These results suggest that lower purity Ga and As source materials can be used during crystal growth to reduce the cost of wafers.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2021

Control of CuPt Ordering in GaInP Grown by Hydride Vapor Phase Epitaxy

We investigate the degree of ordering present in GaInP layers grown by dynamic hydride vapor phase epitaxy (D-HVPE) as a function of various growth conditions. We assess order parameter from both transmission electron and x-ray diffraction and compare these trends to the order parameter estimated by the photoluminescence-determined band gap in the GaInP layers. The degree of ordering increases with deposition temperature and the ratio of gas-phase group V to group III precursors in the reactor. We also investigate the effect of growth rate, demonstrating the capability of HVPE to suppress order through rapid growth rates. Such ordering dependences are consistent with mechanisms established for ordering observed in GaInP grown by organometallic vapor phase epitaxy (OMVPE), but with weaker ordering than GaInP grown by that method.

growth↗
DOE OSTI2021

Improved Contacts for Tandem Cells with Enhanced Effciency Grown by D-HVPE

Dynamic hydride vapor phase epitaxy (D-HVPE) has provided a potential route towards lower cost material growth of III-V photovoltaic devices. A highly doped Ga0.5In0.5P emitter layer is grown in attempt to force passivation at the front of the cell to account for the absence of a suitable window layer in our reactor. Control over dopant diffusion in these materials is thus critical to achieving high-efficiency device performance. Here, we institute a two-step contact layer design that boosts tandem cell efficiencies by minimizing Se diffusion into the underlying emitter layer while still providing sufficiently low contact resistance. Short-circuit current in these devices improves to 8.9 mA/cm2 in an uncoated GaInP/GaAs cell, an improvement of 1.2 mA/cm2 over our previous best cell. Conversion efficiency with the new contact doping scheme is projected to be ~27% with the inclusion of a standard ARC layer.

27 ARPA - Advanced Research Projects Agency-Energy↗
DOE OSTI2020

Patterning Metal Grids for GaAs Solar Cells with Cracked Film Lithography: Quantifying the Cost/Performance Tradeoff

We introduce cracked film lithography (CFL) as a way to reduce the cost of III–V photovoltaics (PV). We spin-coat nanoparticle suspensions onto GaAs thin-film device stacks. The suspensions dry in seconds, forming crack networks that we use as templates through which to electroplate the solar cells’ front metal grids. For the first time, we show that heating the crack template allows it to flow and refill cracks, which decreases crack footprint and improves final grid transmittance. We demonstrate 24.7%-efficient single-junction GaAs solar cells using vacuum-free CFL grids. These devices are only 1.7% (absolute) less efficient than the baseline grids patterned by photolithography with the loss mostly resulting from the reduced transparency of the CFL pattern. Additional optimization could decrease this difference. Initial cost modeling suggests that CFL is more scalable than photolithography: In particular, CFL’s lower materials and equipment costs could greatly reduce the levelized cost of electricity of III–V PV at scale, a potential step toward terrestrial deployment.

14 SOLAR ENERGY↗
DOE OSTI2020

Dynamic Hydride Vapor Phase Epitaxy of III-V Materials for Photovoltaics Applications: Preprint

We demonstrate the uniqueness of Dynamic Hydride Vapor Phase Epitaxy (D-HVPE) to deposit III-V materials for high efficiency and potentially low-cost photovoltaics applications. Unlike traditional HVPE, D-HVPE allows for the deposition of relatively complex heterostructures and devices at high growth rates. We recently achieved record growth rates > 500 µm/h for GaAs and >200 µm/h for GaInP in our D-HVPE, and have not yet reached a growth rate limit for either material. We grew single junction GaAs solar cells at growth rates up to 309 µm/h without significant degradation of solar cell performance. We also demonstrate growth of Al-containing III-V materials in HVPE, a capability that makes D-HVPE more attractive for applications beyond photovoltaics.

D-HVPE↗