Search NASA⌕ Search

Engineering topics

Singh, D

Publications and source records attributed to Singh, D.

At least 19 records

Observation of breakup transfer process for the bound states of {sup 16}O populated from {sup 12}C({sup 6}Li,d) reaction at 20 MeV

The deuteron angular distribution for the {sup 12}C({sup 6}Li,d){sup 16}O* has been measured at 20 MeV populating bound and unbound states of {sup 16}O. Analysis shows a dominance of breakup induced alpha transfer in comparison to a direct alpha transfer process for the bound states. The effect increases as the excitation energy of {sup 16}O decreases, maximizing at the ground state.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Effect of buffer layer growth temperature on epitaxial GaN films deposited by magnetron sputtering

Epitaxial GaN films were deposited by reactive sputtering of a GaAs target in 100 % nitrogen at 700 deg. C on ZnO buffer layers grown at different substrate temperatures over sapphire substrates. High resolution X-ray diffraction measurements and the corresponding analysis show that the growth temperature of buffer layers significantly affects the micro-structural parameters of GaN epilayer, such as lateral coherence length, tilt and twist, while the vertical coherence length remains unaffected. The optimum substrate temperature for buffer layer growth has been found to be 300 deg. C. High epitaxial quality GaN film grown on such a buffer layer exhibited micro strain of 1.8x10{sup -4} along with screw and edge type dislocation densities of 7.87x10{sup 9} and 1.16x10{sup 11}, respectively.

36 MATERIALS SCIENCE↗

Effect of substrate temperature on microstructure of epitaxial ZnO films grown on sapphire by sputtering

The microstructure of epitaxial ZnO films on (0001) sapphire substrates deposited by reactive sputtering in substrate temperature (T{sub s}) range of 100 - 500 deg. C were investigated by High-resolution X-ray diffraction. The studies show the presence of a strained 2D layer along with 3D crystallites at low T{sub s}, whereas 3D growth is dominant at higher T{sub s}, resulting in formation of mosaic structure with lesser point and line defects.

36 MATERIALS SCIENCE↗

Secondary waste form testing : ceramicrete phosphate bonded ceramics.

The cleanup activities of the Hanford tank wastes require stabilization and solidification of the secondary waste streams generated from the processing of the tank wastes. The treatment of these tank wastes to produce glass waste forms will generate secondary wastes, including routine solid wastes and liquid process effluents. Liquid wastes may include process condensates and scrubber/off-gas treatment liquids from the thermal waste treatment. The current baseline for solidification of the secondary wastes is a cement-based waste form. However, alternative secondary waste forms are being considered. In this regard, Ceramicrete technology, developed at Argonne National Laboratory, is being explored as an option to solidify and stabilize the secondary wastes. The Ceramicrete process has been demonstrated on four secondary waste formulations: baseline, cluster 1, cluster 2, and mixed waste streams. Based on the recipes provided by Pacific Northwest National Laboratory, the four waste simulants were prepared in-house. Waste forms were fabricated with three filler materials: Class C fly ash, CaSiO{sub 3}, and Class C fly ash + slag. Optimum waste loadings were as high as 20 wt.% for the fly ash and CaSiO{sub 3}, and 15 wt.% for fly ash + slag filler. Waste forms for physical characterizations were fabricated with no additives, hazardous contaminants, and radionuclide surrogates. Physical property characterizations (density, compressive strength, and 90-day water immersion test) showed that the waste forms were stable and durable. Compressive strengths were >2,500 psi, and the strengths remained high after the 90-day water immersion test. Fly ash and CaSiO{sub 3} filler waste forms appeared to be superior to the waste forms with fly ash + slag as a filler. Waste form weight loss was {approx}5-14 wt.% over the 90-day immersion test. The majority of the weight loss occurred during the initial phase of the immersion test, indicative of washing off of residual unreacted binder components from the waste form surface. Waste forms for ANS 16.1 leach testing contained appropriate amounts of rhenium and iodine as radionuclide surrogates, along with the additives silver-loaded zeolite and tin chloride. The leachability index for Re was found to range from 7.9 to 9.0 for all the samples evaluated. Iodine was below detection limit (5 ppb) for all the leachate samples. Further, leaching of sodium was low, as indicated by the leachability index ranging from 7.6-10.4, indicative of chemical binding of the various chemical species. Target leachability indices for Re, I, and Na were 9, 11, and 6, respectively. Degradation was observed in some of the samples post 90-day ANS 16.1 tests. Toxicity characteristic leaching procedure (TCLP) results showed that all the hazardous contaminants were contained in the waste, and the hazardous metal concentrations were below the Universal Treatment Standard limits. Preliminary scale-up (2-gal waste forms) was conducted to demonstrate the scalability of the Ceramicrete process. Use of minimal amounts of boric acid as a set retarder was used to control the working time for the slurry. Flexibility in treating waste streams with wide ranging compositional make-ups and ease of process scale-up are attractive attributes of Ceramicrete technology.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Reaction mechanism in the {sup 20}Ne+{sup 59}Co system at 3-7 MeV/nucleon, and observation of entrance-channel mass-asymmetry of the incomplete fusion fraction

Incomplete fusion of {sup 20}Ne with {sup 59}Co has been investigated at 3-7 MeV/nucleon using the measurement and analysis of excitation functions. The recoil-catcher technique followed by offline gamma-ray spectroscopy has been employed. Evaporation residues are found to have contributions from precursor decays, which have been separated out from the measured cumulative cross sections of evaporation residues. Measured independent cross sections are compared with PACE-2 predictions. The PACE-2 calculations are carried out for evaporation residues formed in complete fusion (CF), and the parameters are optimized so as to reproduce the cross section of evaporation residues produced exclusively in CF, e.g., xn and pxn products. With these parameters, the predicted CF cross sections for alpha emission products are calculated. Any substantial enhancement in the experimental cross section over the PACE-2 prediction is taken as a signature of incomplete fusion (ICF). The analysis indicates the occurrence of incomplete fusion involving the breakup of {sup 20}Ne into {sup 16}O + {sup 4}He and/or {sup 12}C + {sup 8}Be(2{alpha}) followed by fusion of one of the fragments with the target nucleus {sup 59}Co. These data also suggest that the probability of incomplete fusion increases with the projectile energy. Moreover, the ICF probability is found to increase with entrance-channel mass-asymmetry of the projectile-target systems.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Nanofluids for heat transfer : an engineering approach.

An overview of systematic studies that address the complexity of nanofluid systems and advance the understanding of nanoscale contributions to viscosity, thermal conductivity, and cooling efficiency of nanofluids is presented. A nanoparticle suspension is considered as a three-phase system including the solid phase (nanoparticles), the liquid phase (fluid media), and the interfacial phase, which contributes significantly to the system properties because of its extremely high surface-to-volume ratio in nanofluids. The systems engineering approach was applied to nanofluid design resulting in a detailed assessment of various parameters in the multivariable nanofluid systems. The relative importance of nanofluid parameters for heat transfer evaluated in this article allows engineering nanofluids with desired set of properties.

42 ENGINEERING↗

USE OF CEMENTITIOUS MATERIALS FOR SRS REACTOR FACILITY IN-SITU DECOMMISSIONING - 11620

The United States Department of Energy (US DOE) concept for facility in-situ decommissioning (ISD) is to physically stabilize and isolate in tact, structurally sound facilities that are no longer needed for their original purpose of, i.e., producing (reactor facilities), processing (isotope separation facilities) or storing radioactive materials. The Savannah River Site 105-P and 105-R Reactor Facility ISD requires about 250,000 cubic yards of grout to fill the below grade structure. The fills are designed to prevent subsidence, reduce water infiltration, and isolate contaminated materials. This work is being performed as a Comprehensive Environmental Response, Compensations and Liability Act (CERCLA) action and is part of the overall soil and groundwater completion projects for P- and R-Areas. Cementitious materials were designed for the following applications: (1) Below grade massive voids/rooms: Portland cement-based structural flowable fills for - Bulk filling, Restricted placement and Underwater placement. (2) Special below grade applications for reduced load bearing capacity needs: Cellular portland cement lightweight fill (3) Reactor vessel fills that are compatible with reactive metal (aluminum metal) components in the reactor vessels: Calcium sulfoaluminate flowable fill, and Magnesium potassium phosphate flowable fill. (4) Caps to prevent water infiltration and intrusion into areas with the highest levels of radionuclides: Portland cement based shrinkage compensating concrete. A system engineering approach was used to identify functions and requirements of the fill and capping materials. Laboratory testing was performed to identify candidate formulations and develop final design mixes. Scale-up testing was performed to verify material production and placement as well as fresh and cured properties. The 105-P and 105-R ISD projects are currently in progress and are expected to be complete in 2012. The focus of this paper is to describe the (1) grout mixes for filling the reactor vessels, and (2) a specialty grout mix to fill a selected portion of the P-Reactor Disassembly Basin. Details of the grout mixes designed for ISD of he SRS Reactor Disassembly Basins and below grade portions of the 105-Buildings was described elsewhere. Material property test results, placement strategies, full-scale production and delivery systems will also be described.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Analysis of failed and nickel-coated 3093 beam clamp components at the East Tennessee Technology Park (ETTP).

The U.S. Department of Energy and its contractor, Bechtel Jacobs Company (BJC), are undertaking a major effort to clean up the former gaseous diffusion facility (K-25) located in Oak Ridge, TN. The decontamination and decommissioning activities require systematic removal of contaminated equipment and machinery followed by demolition of the buildings. As part of the cleanup activities, a beam clamp, used for horizontal life lines (HLLs) for fall protection, was discovered to be fractured during routine inspection. The beam clamp (yoke and D-ring) was a component in the HLL system purchased from Reliance Industries LLC. Specifically, the U-shaped stainless steel yoke of the beam clamp failed in a brittle mode at under less than 10% of the rated design capacity of 14,500 lb. The beam clamp had been in service for approximately 16 months. Bechtel Jacobs approached Argonne National Laboratory to assist in identifying the root cause of the failure of the beam clamp. The objectives of this study were to (1) review the prior reports and documents on the subject, (2) understand the possible failure mechanism(s) that resulted in the failed beam clamp components, (3) recommend approaches to mitigate the failure mechanism(s), and (4) evaluate the modified beam clamp assemblies. Energy dispersive x-ray analysis and chemical analysis of the corrosion products on the failed yoke and white residue on an in-service yoke indicated the presence of zinc, sulfur, and calcium. Analysis of rainwater in the complex, as conducted by BJC, indicated the presence of sulfur and calcium. It was concluded that, as a result of galvanic corrosion, zinc from the galvanized components of the beam clamp assembly (D-ring) migrated to the corroded region in the presence of the rainwater. Under mechanical stress, the corrosion process would have accelerated, resulting in the catastrophic failure of the yoke. As suggested by Bechtel Jacobs personnel, hydrogen embrittlement as a consequence of corrosion was also explored as a failure mechanism. Corroded and failed yoke samples had hydrogen concentrations of 20-60 ppm. However, the hydrogen content reduced to 4-11 ppm (similar to baseline as-received yoke samples) when the corrosion products were polished off. The hydrogen content in the scraped off corrosion product powders was >7000 ppm. These results indicate that hydrogen is primarily present in the corrosion products and not in the underlying steel. Rockwell hardness values on the corroded yoke and D-rings were R{sub c} {approx} 41-46. It was recommended to the beam clamp manufacturer that the beam clamp components be annealed to reduce the hardness values so that they are less susceptible to brittle failure. Upon annealing, hardness values of the beam clamp components reduced to R{sub c} {approx} 25. Several strategies were recommended and put in place to mitigate failure of the beam clamp components: (a) maintain hardness levels of both yokes and D-rings at R{sub c} < 35, (b) coat the yoke and D-rings with a dual coating of nickel (with 10% phosphorus) to delay corrosion and aluminum to prevent galvanic corrosion since it is more anodic to zinc, and (c) optimize coating thicknesses for nickel and aluminum while maintaining the physical integrity of the coatings. Evaluation of the Al- and Ni-coated yoke and D-ring specimens indicated they appear to have met the recommendations. Average hardness values of the dual-coated yokes were R{sub c} {approx} 25-35. Hardness values of dual-coated D-ring were R{sub c} {approx} 32. Measured average coating thicknesses for the aluminum and nickel coatings for yoke samples were 22 {micro}m (0.9 mils) and 80 {micro}m (3 mils), respectively. The D-rings also showed similar coating thicknesses. Microscopic examination showed that the aluminum coating was well bonded to the underlying nickel coating. Some observed damage was believed to be an artifact of the cutting-and-polishing steps during sample preparation for microscopy.

08 HYDROGEN↗

Mechanisms and models of effective thermal conductivities of nanofluids.

The physical mechanisms and mathematical models of the effective thermal conductivities of nanofluids have long been of interest to the nanofluid research community because the effective thermal conductivities of nanofluids cannot generally be fully explained and predicted by classical effective medium theories. This review article summarizes considerable progress made on this topic. Specifically, the physical mechanisms and mathematical models of the effective thermal conductivities of nanofluids are reviewed, the potential contributions of those physical mechanisms are evaluated, and the comparisons of the theoretical predictions and experimental data are presented along with opportunities for future research.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Developmemt, characterization, production, and demonstration of nanofluids for industrial cooling applications. Quarterly report #7.

Pumping power measurements have been made on a series of 40-nm boehmite (AlOOH) alumina ''bricks'' (2 - 8 vol. percent in water). The alumina nanoparticles were obtained from Sasol and are designated as ''Catapal-200''. The pH of all compositions was adjusted to 3.2{+-}0.5. A complete characterization of the particles and their nanofluid thermal properties has been published in Journal of Applied Physics 106, 014304 (2009). While the nanofluid doesn't show large enhancements, it nevertheless serves as good comparisons between the experimental results and calculated results.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

On possible variation in the cosmological Baryon fraction.

The fraction of matter that is in the form of baryons or dark matter could have spatial fluctuations in the form of baryon-dark matter isocurvature fluctuations. We use big bang nucleosynthesis calculations compared with observed light element abundances as well as galaxy cluster gas fractions to constrain cosmological variations in the baryon fraction. Light element abundances constrain spatial variations to be less than 26-27%, while a sample of 'relaxed' galaxy clusters shows spatial variations in gas fractions less than 8%. Larger spatial variations could cause differential screening of the primary cosmic microwave background anisotropies, leading to asymmetries in the fluctuations and ease some tension with the halo-star 7Li abundance. Fluctuations within our allowed bounds can lead to 'B-mode' CMB polarization anisotropies at a non-negligible level.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Incomplete fusion dynamics by spin distribution measurements

Spin distributions for various evaporation residues populated via complete and incomplete fusion of {sup 16}O with {sup 124}Sn at 6.3 MeV/nucleon have been measured, using charged particles (Z=1,2)-{gamma} coincidence technique. Experimentally measured spin distributions of the residues produced as incomplete fusion products associated with 'fast'{alpha}- and 2{alpha}-emission channels observed in the 'forward cone' are found to be distinctly different from those of the residues produced as complete fusion products. Moreover, 'fast'{alpha}-particles that arise from larger angular momentum in the entrance channel are populated at relatively higher driving input angular momentum than those produced through complete fusion. The incomplete fusion residues are populated in a limited, higher-angular-momentum range, in contrast to the complete fusion products, which are populated over a broad spin range.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Induction annealing and subsequent quenching : effect on the thermoelectric properties of boron-doped nanographite ensembles.

Boron-doped nanographite ensembles (NGEs) are interesting thermoelectric nanomaterials for high temperature applications. Rapid induction annealing and quenching has been applied to boron-doped NGEs using a relatively low-cost, highly reliable, laboratory built furnace to show that substantial improvements in thermoelectric power factors can be achieved using this methodology. Details of the design and performance of this compact induction furnace as well as results of the thermoelectric measurements will be reported here.

36 MATERIALS SCIENCE↗

Particle size and interfacial effects on heat transfer characteristics of water and {alpha}-SiC nanofluids.

The effect of average particle sizes on basic macroscopic properties and heat transfer performance of {alpha}-SiC/water nanofluids was investigated. The average particle sizes, calculated from the specific surface area of nanoparticles, were varied from 16 to 90 nm. Nanofluids with larger particles of the same material and volume concentration provide higher thermal conductivity and lower viscosity increases than those with smaller particles because of the smaller solid/liquid interfacial area of larger particles. It was also demonstrated that the viscosity of water-based nanofluids can be significantly decreased by pH of the suspension independently from the thermal conductivity. Heat transfer coefficients were measured and compared to the performance of base fluids as well as to nanofluids reported in the literature. Criteria for evaluation of the heat transfer performance of nanofluids are discussed and optimum directions in nanofluid development are suggested.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Particle shape effects on thermo-physical properties of alumina nanofluids.

The thermal conductivity and viscosity of various shapes of alumina nanoparticles in a fluid consisting of equal volumes of ethylene glycol and water were investigated. Experimental data were analyzed and accompanied by theoretical modeling. Enhancements in the effective thermal conductivities due to particle shape effects expected from Hamilton-Crosser equation are strongly diminished by interfacial effects proportional to the total surface area of nanoparticles. On the other hand, the presence of nanoparticles and small volume fractions of agglomerates with high aspect ratios strongly increases viscosity of suspensions due to structural constrains. Nanoparticle surface charge also plays an important role in viscosity. It is demonstrated that by adjusting pH of nanofluid, it is possible to reduce viscosity of alumina nanofluid without significantly affecting thermal conductivity. Efficiency of nanofluids (ratio of thermal conductivity and viscosity increase) for real-life cooling applications is evaluated in both the laminar and turbulent flow regimes using the experimental values of thermal conductivity and viscosity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗