Search NASA⌕ Search

Engineering topics

Stern, J. A.

Publications and source records attributed to Stern, J. A..

32 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

NbN/MgO/NbN edge-geometry tunnel junctions

The fabrication and low-frequency testing of the first edge-geometry NbN/MgO/NbN superconducting tunnel junctions are reported. The use of an edge geometry allows very small junction areas to be obtained, while the all-NbN electrodes permit operation at 8-10 K with a potential maximum operating frequency above 1 THz. Edge definition in the base NbN film was accomplished utilizing Ar ion milling with an Al2O3 milling mask, followed by a lower energy ion cleaning step. This process has produced all-refractory-material tunnel junctions with areas as small as 0.1 sq micron, resistance-area products less than 21 ohm sq micron, and subgap to normal state resistance ratios larger than 18.

Hunt, B. D.↗
NASA NTRS1989

NbN/MgO/NbN SIS tunnel junctions for submm wave mixers

The authors report on the fabrication and testing of all-refractory NbN/MgO/NbN SIS (superconductor-insulator-superconductor) tunnel junctions for use as high-frequency mixers. Progress in the development of techniques for the fabrication of submicron-area tunnel junctions is described. Junction structures which have been investigated include mesa, crossline, and edge geometries. Using reactive sputtering techniques, NbN tunnel junctions with critical currents in excess of 104 A/sq cm have been fabricated with Vm values as high as 65 mV and areas down to 0.1 sq micron. Specific capacitance measurements on NbN/MgO/NbN mesa-type tunnel junctions give values in the range 60-90 fF/sq micron. These SIS tunnel junctions have been integrated with antennas and coupling structures for mixer tests in a waveguide receiver at 207 GHz. Preliminary mixer results are reported.

Stern, J. A.↗
NASA NTRS1987

All NbN tunnel junction fabrication

The development of SIS tunnel junctions based on NbN for mixer applications in the submillimeter range is reported. The unique technological challenges inherent in the development of all refractory-compound superconductor-based tunnel junctions are highlighted. Current deposition and fabrication techniques are discussed, and the current status of all-NbN tunnel junctions is reported.

Leduc, H. G.↗
NASA NTRS1987

Energy-gap spectroscopy of superconductors using a tunneling microscope

A unique scanning tunneling microscope (STM) system has been developed for spectroscopy of the superconducting energy gap. High-resolution control of tunnel current and voltage allows for measurement of superconducting properties at tunnel resistance levels 100-1000 greater than that achieved in prior work. The previously used STM methods for superconductor spectroscopy are compared to those developed for the work reported here. Superconducting energy-gap spectra are reported for three superconductors, Pb, PbBi, and NbN, over a range of tunnel resistance. The measured spectra are compared directly to theory.

Le Duc, H. G.↗
NASA NTRS1975

Challenges of short-haul air transportation

Short-haul transportation systems are characterized by low average utilization, high peak but low average passenger demand, severe competition from other transportation modes, high fixed costs and high operating costs. Studies were conducted to analyze the operational requirements and market size for medium-density air transportation. The determination of the aircraft that will most efficiently meet the requirements of this market requires the careful evaluation of variable parameters such as engine cycles, payload, field length range and type of high-lift system. Low noise, low cost and thrust reversing capability are the basic criteria for the propulsion system. It is concluded that aircraft of less than 50-seat capacity cannot generate satisfactory profits operating in the medium-density market.

Galloway, T. L.↗
NASA NTRS1974

Viking heat sterilization - Progress and problems

The Viking Mars landers to be launched in 1975 will carry experiments in biology, planetology, and atmospheric physics. A terminal dry-heat sterilization process using an inert gas was chosen to meet planetary quarantine requirements and preclude contamination of the biology experiment by terrestrial organisms. Deep sterilization is performed at the component level and terminal surface sterilization at the system level. Solutions to certain component problems relating to sterilization are discussed, involving the gyroscope, tape recorder, battery, electronic circuitry, and outgassing. Heat treatment placed special requirements on electronic packaging, including fastener preload monitoring and solder joints. Chemical and physical testing of nonmetallic materials was performed to establish data on their behavior in heat-treatment and vacuum environments. A Thermal Effects Test Model and a Proof Test Capsule were used. It is concluded that a space vehicle can be designed and fabricated to withstand heat sterilization requirements.

Daspit, L. P.↗