Search NASA⌕ Search

Engineering topics

Stubbs, Sandy M.

Publications and source records attributed to Stubbs, Sandy M..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Tests of highly loaded skids on a concrete runway

Skids have been used at various times for aircraft landing gear ever since the Wright Flyer appeared in the early 1900's. Typically, skids have been employed as aircraft landing gear either at low speeds or at low bearing pressures. Tests were conducted to examine the friction and wear characteristics of various metals sliding on a rough, grooved concrete runway. The metals represented potential materials for an overload protection skid for the Space Shuttle orbiter. Data from tests of six skid specimens conducted at higher speeds and bearing pressures than those of previous tests in the open literature are presented. Skids constructed of tungsten with embedded carbide chips exhibited the lowest wear, whereas a skid constructed of Inconel 718 exhibited high wear rates. Friction coefficients for all the skid specimens were moderate and would provide adequate stopping performance on a long runway. Because of its low wear rate, a skid constructed of tungsten with embedded carbide chips is considered to be a likely candidate for an aircraft skid or overload protection skid.

Stubbs, Sandy M.↗
NASA NTRS1993

Studies of Shuttle orbiter arrestment system

Scale model studies of the Shuttle Orbiter Arrestment System (AS) were completed with a 1/27.5-scale model at the NASA Langley Research Center. The purpose of these studies was to determine the proper configuration for a net arrestment system to bring the orbiter to a safe stop with minimal damage in the event of a runway overrun. Tests were conducted for runway on-centerline and off-centerline engagements at simulated speeds up to approximately 100 knots (full scale). The results of these tests defined the interaction of the net and the orbiter, the dynamics of off-centerline engagements, and the maximum number of vertical net straps that may become entangled with the nose gear. In addition to these tests, a test program with a 1/8-scale model was conducted by the arrestment system contractor, and the results are presented in the appendix.

Davis, Pamela A.↗
NASA NTRS1993

Method and apparatus for cleaning rubber deposits from airport runways and roadways

A method and apparatus for cleaning rubber deposits from surfaces such as airport runways and roadways is disclosed. The apparatus includes a large vehicle that has the capacity to be loaded so as to effectively add weight to the rubber cleaning tires of the vehicle. In addition, the vehicle has a water tank and sprinkler system so that the surface may be wetted down in front of the tires as the vehicle proceeds across the surface. The cleaning tires of the apparatus are aligned so that they are at a yaw angle to the direction of travel, and the cleaning tire assembly is attached to the underside of the trailer of the vehicle and positioned between a forward and rear water tank. In addition, this tire assembly is equipped with a means of loading the tires onto the contaminated surface. The method comprises driving such a vehicle at low speeds down the surface as the road is being wet in front of the cleaning tires. The effect of the angled tires is to create a scrubbing action that not only heats the rubber deposits by friction but also causes it to be removed from the surface. The rubber that does not stick to the cleaning tires is then removed from the surface by sweeping.

Stubbs, Sandy M.↗
NASA NTRS1993

NASA evaluation of Type 2 chemical depositions

Recent findings from NASA Langley tests to define effects of aircraft Type 2 chemical deicer depositions on aircraft tire friction performance are summarized. The Aircraft Landing Dynamics Facility (ALDF) is described together with the scope of the tire cornering and braking friction tests conducted up to 160 knots ground speed. Some lower speed 32 - 96 km/hr (20 - 60 mph) test run data obtained using an Instrumented Tire Test Vehicle (ITTV) to determine effects of tire bearing pressure and transverse grooving on cornering friction performance are also discussed. Recommendations are made concerning which parameters should be evaluated in future testing.

Yager, Thomas J.↗
NASA NTRS1992

The effect of runway surface and braking on Shuttle Orbiter main gear tire wear

In 1988, a 1067 m long touchdown zone on each end of the Kennedy Space Center (KSC) Shuttle Landing Facility (SLF) was modified from its original heavy-broom finish with transverse grooves configuration to a longitudinal corduroy surface texture with no transverse grooves. The intent of this modification was to reduce the spin-up wear on the Orbiter main gear tires and provide for somewhat higher crosswind capabilities at that site. The modification worked well, so it was proposed that the remainder of the runway be modified as well to permit even higher crosswind landing capability. Tests were conducted at the NASA Langley Aircraft Landing Dynamics Facility (ALDF) to evaluate the merit of such a modification. This paper discusses the results of these tests, and explains why the proposed modification did not provide the expected improvement and thus was not implemented. Also, in an ongoing program to evaluate the origin of various tire wear phenomenon, a series of tests was conducted to evaluate the effect of braking on tire wear. Finally, a modified tire is discussed in terms of its wear performance under rollout and braking operations.

Daugherty, Robert H.↗
NASA NTRS1992

Langley Aircraft Landing Dynamics Facility

NASA Reference Publication reports on NASA Langley Research Center's recent upgrading of Landing Loads Track (LLT) to improve capability of low-cost testing of conventional and advanced landing-gear systems. Features include ability to test aircraft landing-gear systems on actual runway surfaces at operational ground speeds and loading conditions. Historical overview of original LLT given, followed by detailed description of systems and operational capabilities of new ALDF.

Davis, Pamela A.↗
NASA NTRS1991

26 x 6.6 radial-belted aircraft tire performance

Preliminary results from testing of 26 x 6.6 radial-belted and bias-ply aircraft tires at NASA Langley's Aircraft Landing Dynamics Facility (ALDF) are reviewed. The 26 x 6.6 tire size evaluation includes cornering performance tests throughout the aircraft ground operational speed range for both dry and wet runway surfaces. Static test results to define 26 x 6.6 tire vertical stiffness properties are also presented and discussed.

Davis, Pamela A.↗
NASA NTRS1990

Aircraft radial-belted tire evaluation

An overview is given of the ongoing joint NASA/FAA/Industry Surface Traction And Radial Tire (START) Program being conducted at NASA Langley's Aircraft Landing Dynamics Facility (ALDF). The START Program involves tests using three different tire sizes to evaluate tire rolling resistance, braking, and cornering performance throughout the aircraft ground operational speed range for both dry and wet runway surfaces. Preliminary results from recent 40 x 14 size bias-ply, radial-belted, and H-type aircraft tire tests are discussed. The paper concludes with a summary of the current program status and planned ALDF test schedule.

Yager, Thomas J.↗
NASA NTRS1990

Measurement Of Water Sprays Generated By Airplane Tires

Experimental investigation conducted at NASA Langley Research Center to measure rate of flow and trajectory of water spray generated by tire operating on flooded runway. Potential application to both aircraft and automotive industries, with particular application to manufacturers of tires.

Daugherty, Robert H.↗
NASA NTRS1989

Orbiter post-tire failure and skid testing results

An investigation was conducted at the NASA Langley Research Center's Aircraft Landing Dynamics Facility (ALDF) to define the post-tire failure drag characteristics of the Space Shuttle Orbiter main tire and wheel assembly. Skid tests on various materials were also conducted to define their friction and wear rate characteristics under higher speed and bearing pressures than any previous tests. The skid tests were conducted to support a feasibility study of adding a skid to the orbiter strut between the main tires to protect an intact tire from failure due to overload should one of the tires fail. Roll-on-rim tests were conducted to define the ability of a standard and a modified orbiter main wheel to roll without a tire. Results of the investigation are combined into a generic model of strut drag versus time under failure conditions for inclusion into rollout simulators used to train the shuttle astronauts.

Daugherty, Robert H.↗
NASA NTRS1989

Cornering and wear characteristics of the Space Shuttle Orbiter nose-gear tire

Tests of the Space Shuttle Orbiter nose-gear tire have been completed at NASA Langley's Aircraft Landing Dynamics Facility. The purpose of these tests was to determine the cornering and wear characteristics of the Space Shuttle Orbiter nose-gear tire under realistic operating conditions. The tire was tested on a simulated Kennedy Space Center runway surface at speeds from 100 to 180 kts. The results of these tests defined the cornering characteristics which included side forces and associated side force friction coefficient over a range of yaw angles from 0 deg to 12 deg. Wear characteristics were defined by tire tread and cord wear over a yaw angle range of 0 deg to 4 deg under dry and wet runway conditions. Wear characteristics were also defined for a 15 kt crosswind landing with two blown right main-gear tires and nose-gear steering engaged.

Davis, Pamela A.↗
NASA NTRS1988

Spin-up studies of the Space Shuttle Orbiter main gear tire

One of the factors needed to describe the wear behavior of the Space Shuttle Orbiter main gear tires is their behavior during the spin-up process. An experimental investigation of tire spin-up processes was conducted at the NASA Langley Research Center's Aircraft Landing Dynamics Facility. During the investigation, the influence of various parameters such as forward speed and sink speed on tire spin-up forces were evaluated. A mathematical model was developed to estimate drag forces and spin-up times and is presented. The effect of prerotation was explored and is discussed. Also included is a means of determining the sink speed of the orbiter at touchdown based upon the appearance of the rubber deposits left on the runway during spinup.

Daugherty, Robert H.↗
NASA NTRS1988

Shuttle Orbiter arrestment system studies

Scale model studies of the Shuttle Orbiter arrestment system were conducted to determine the proper net arrestment system configuration to bring the Orbiter to a safe stop in the event of a runway overshoot. Areas of interest include the effect of various net geometries on net engagement of the nose gear and main gear; and whether or not the top bundle contacts the crew cabin window. The model tests indicated that the net arrestment system was properly designed to bring the Orbiter to a safe stop with minimal amount of damage. The test procedures and data are presented.

Davis, Pamela A.↗
NASA NTRS1988

Shuttle landing runway modification to improve tire spin-up wear performance

This paper presents the results of a series of tire spin-up wear tests on a simulated Kennedy Space Center (KSC) runway that were carried out to investigate the tire wear problem for Space Shuttle landings on the KSC runway and to test several modifications of the runway surface designed to alleviate the problem. It was found that the runway surface produced by a concrete smoothing machine using cutters spaced one and three-quarters blades per centimeter provided adequate wet cornering while limiting spin-up wear. Based on the test results, the KSC runway was smoothed for about 1066 m at each end, leaving the original high friction surface, for better wet steering and braking, in the 2438-m central section.

Daugherty, Robert H.↗
NASA NTRS1988

Cornering characteristics of the main-gear tire of the space shuttle orbiter

An experimental investigation was conducted at the NASA Langley Research Center to study the effects of various vertical load and yaw angle conditions on the cornering behavior of the Space Shuttle Orbiter main gear tire. Measured parameters included side and drag force, side and drag force coefficients, aligning torque, and overturning torque. Side force coefficient was found to increase as yaw angle was increased, but decreased as the vertical load was increased. Drag force was found to increase as vertical load was increased at constant yaw angles. Aligning torque measurements indicated that the tire is stable in yaw.

Daugherty, Robert H.↗
NASA NTRS1987

Langley Aircraft Landing Dynamics Facility

The Langley Research Center has recently upgraded the Landing Loads Track (LLT) to improve the capability of low-cost testing of conventional and advanced landing gear systems. The unique feature of the Langley Aircraft Landing Dynamics Facility (ALDF) is the ability to test aircraft landing gear systems on actual runway surfaces at operational ground speeds and loading conditions. A historical overview of the original LLT is given, followed by a detailed description of the new ALDF systems and operational capabilities.

Davis, Pamela A.↗
NASA NTRS1987

Cornering and wear behavior of the Space Shuttle Orbiter main gear tire

One of the factors needed to describe the handling characteristics of the Space Shuttle Orbiter during the landing rollout is the response of the vehicle's tires to variations in load and yaw angle. An experimental investigation of the cornering characteristics of the Orbiter main gear tires was conducted at the NASA Langley Research Center Aircraft Landing Dynamics Facility. This investigation compliments earlier work done to define the Orbiter nose tire cornering characteristics. In the investigation, the effects of load and yaw angle were evaluated by measuring parameters such as side load and drag load, and obtaining measurements of aligning torque. Because the tire must operate on an extremely rough runway at the Shuttle Landing Facility at Kennedy Space Center (KSC), tests were also conducted to describe the wear behavior of the tire under various conditions on a simulated KSC runway surface. Mathematical models for both the cornering and the wear behavior are discussed.

Daugherty, Robert H.↗