Search NASA⌕ Search

Engineering topics

Sun, Chengjun

Publications and source records attributed to Sun, Chengjun.

At least 55 records · Page 3

Enabling High-Performance NASICON-Based Solid-State Lithium Metal Batteries Towards Practical Conditions

Solid-state lithium metal batteries (SSLMBs) are promising next-generation high-energy rechargeable batteries. However, the practical energy densities of the reported SSLMBs have been significantly overstated due to the use of thick solid-state electrolytes, thick lithium (Li) anodes, and thin cathodes. Here, a high-performance NASICON-based SSLMB using a thin (60 µm) Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) electrolyte, ultrathin (36 µm) Li metal, and high-loading (8 mg cm -2 ) LiFePO 4 (LFP) cathode is reported. The thin and dense LAGP electrolyte prepared by hot-pressing exhibits a high Li ionic conductivity of 1 × 10 -3 S cm -1 at 80 °C. The assembled SSLMB can thus deliver an increased areal capacity of ≈1 mAh cm -2 at C/5 with a high capacity retention of ≈96% after 50 cycles under 80 °C. Furthermore, it is revealed by synchrotron X-ray absorption spectroscopy and in situ high-energy X-ray diffraction that the side reactions between LAGP electrolyte and LFP cathode are significantly suppressed, while rational surface protection is required for Ni-rich layered cathodes. This study provides valuable insights and guidelines for the development of high-energy SSLMBs towards practical conditions.

25 ENERGY STORAGE↗

Visually resolving the direct Z-scheme heterojunction in CdS@ZnIn 2 S 4 hollow cubes for photocatalytic evolution of H 2 and H 2 O 2 from pure water

We report the direct Z-scheme heterojunction has been recently emerging as an appealing architecture for photocatalysts design. Its efficiency depends on the interfacial and structural features of the photocatalysts. Herein, the two-dimensional ZnIn 2 S 4 nanosheets are grown on the surface of CdS hollow cubes to construct the CdS@ZnIn 2 S 4 hierarchical hollow photocatalysts with chemically bonded interface. The visualized measurements based on spatial-resolved surface photovoltage spectroscopy, combined with other spectroscopic and simulation investigations, clearly disclose that the CdS@ZnIn 2 S 4 hollow cubes constitute a highly efficient direct Z-scheme system. This accounts for the stoichiometric generation of H 2 and H 2 O 2 from pure water observed for the CdS@ZnIn 2 S 4 sulfide-only photocatalysts under visible light irradiation with an apparent quantum efficiency of 1.63 % at 400 nm. The present work demonstrates an effective protocol to achieve comprehensive insights into the charge transfer route at semiconductor heterojunction, and offers a viable way for constructing efficient sulfide-only photocatalysts for driving water splitting reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Local spring effect in titanium-based layered oxides

Titanium-based layered oxides (TLOs) are one of the most promising electrode material families for sodium-ion batteries (NIBs) due to their smooth charge/discharge profiles and excellent cycle performance. However, the reaction mechanism of these materials, especially the reason for the disappearance of multiple voltage plateaus, is still not clear. Herein, two representative TLOs (Na 2/3 Ni 1/3 Ti 2/3 O 2 and Na 2/3 Co 1/3 Ti 2/3 O 2 ) with the same P2 crystal structure have been studied to scrutinize those unexplained issues. In situ synchrotron high-energy X-ray diffraction revealed a solid solution reaction mechanism for both, suggesting the absence of rigid phase transitions upon electrochemical cycling. An interesting “spring effect” of the TiO 6 octahedron, i.e., the reversible vibration of the central Ti atom inside the local octahedron upon electrochemical redox, was demonstrated by advanced X-ray absorption spectroscopy and theoretical calculations. Such an effect could suppress the rigid phase transitions, and result in smooth charge/discharge profiles and enhanced cycle stability. Finally, this work not only accounts for the disappearance of multiple voltage plateaus of TLOs for NIBs, but also provides an effective local-structure viewpoint to increase the cycle stability of electrode materials for other advanced battery systems.

25 ENERGY STORAGE↗

Negative and zero thermal expansion in α-(Cu 2-x Znx)V 2 O 7 solid solutions

Negative or zero thermal expansion (NTE or ZTE) of materials is intriguing for controllable thermal expansion. In this work, we report a series of orthorhombic α-Cu 2- x Zn x V 2 O 7 ( x = 0, 0.1, 0.2), in which the volumetric coefficients of thermal expansion are successfully tuned from -10.19 × 10 -6 K -1 to -1.58 × 10 -6 K -1 in the temperature range of 100–475 K by increasing the content of Zn 2+ . It has been revealed that the transverse vibrations of oxygen bonded with vanadium are dominant in the contraction of the bc plane, leading to the overall volume NTE in α-Cu 2 V 2 O 7 . The introduction of Zn 2+ densifies the crystal structure, which is presumed to suppress the space of transverse vibrations and results in the ZTE in α-Cu 1.8 Zn 0.2 V 2 O 7 . This work presents an effective method to realize ZTE in anisotropic framework systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Unexpected trends in the enhanced Ce 3+ surface concentration in ceria–zirconia catalyst materials

Despite the immense importance of ceria–zirconia solid solutions in heterogeneous catalysis, and the growing consensus that catalytic activity correlates with the concentration of reduced Ce 3+ species and accompanying oxygen vacancies, the extent of reduction at the surfaces of these materials, where catalysis occurs, is unknown. Using angle-resolved X-ray Absorption Near Edge Spectroscopy (XANES), we quantify under technologically relevant conditions the Ce 3+ concentration in the surface (2–3 nm) and bulk regions of ceria–zirconia films grown on single crystal yttria-stabilized zirconia, YSZ (001). In all circumstances, we observe substantial Ce 3+ enrichment at the surface relative to the bulk. Surprisingly, the degree of enhancement is highest in the absence of Zr. This behavior stands in direct contrast to that of the bulk in which the Ce 3+ concentration monotonically increases with increasing Zr content. Overall, these results suggest that while Zr enhances the oxygen storage capacity in ceria, undoped ceria may have higher surface catalytic activity. They further urge caution in the use of bulk properties as surrogate descriptors for surface characteristics and hence catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Preparation of Nonprecious Metal Electrocatalysts for the Reduction of Oxygen Using a Low-Temperature Sacrificial Metal

Non-platinum group metal (non-PGM) electrocatalysts for the oxygen reduction reaction (ORR) are generally composed of iron, nitrogen, and carbon synthesized through high-temperature pyrolysis. Among the various types of precursors, metal-organic frameworks (MOFs), zeolitic imidazolate framework (ZIF)-8 in particular, have often been used in the synthesis. The pyrolysis of ZIF-8 precursor relies on the use of Zn as a sacrificial metal (SM), and the optimal processing temperatures often exceed 1000 degrees C to generate active non-PGM catalysts. The high pyrolysis temperature tends to result in heterogeneous active moieties ranging from Fe single atoms to nanoparticles. In this study, we present the synthesis of non-PGM catalysts using Cd as the sacrificial metal instead of Zn. By using Cd, we were able to generate active non-PGM electrocatalysts from the MOF precursors at a low pyrolysis temperature of 750 degrees C, which helps preserve the single atomic iron active sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Engineering Active Fe Sites on Nickel–Iron Layered Double Hydroxide through Component Segregation for Oxygen Evolution Reaction

Nickel-iron layered double hydroxide (NiFe LDH) is a promising oxygen evolution reaction (OER) electrocatalyst under alkaline conditions. Much research has been performed to understand the structure-activity relationship of NiFe LDH under OER conditions. However, the specific role of the Fe species remains unclear and under debate. Herein, based on DFT calculations, it was discovered that the edge Fe sites show higher activity towards OER than either the edge Ni sites or lattice sites. Therefore, a facile acid-etching method was proposed to controllably induce the formation of edge Fe sites in NiFe LDH, and the obtained sample exhibited higher OER activity. X-ray absorption near edge structure and extended X-ray absorption fine structure analyses further revealed that the interaction of the edge Fe species with Ni is believed to contribute to the enhancement of the OER performance. This work provides a new understanding of the structure-activity relationship in NiFe LDH and offers a facile method for the design of efficient electrocatalysts in an alkaline environment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Role of Ru in Improving the Activity of Pd toward Hydrogen Evolution and Oxidation Reactions in Alkaline Solutions

Improving the reaction kinetics of hydrogen evolution and oxidation reactions (HER/HOR) in alkaline media is critical to promote the development of alkaline fuel cells and electrolyzers. Here, we prepared Pd 3 Ru alloy nanocatalysts with Ru segregated on the surfaces, forming adatoms and clusters. This structure dramatically lowered the overpotential of Pd toward HER in 1 M KOH by 104 mV at 10 mA cm –2 . The HER activity was even higher than that of Pt (6 mV improvement at 10 mA cm –2 ). Theoretical simulation results revealed that Ru adatoms/clusters on the surface could weaken the hydrogen-binding energy and promote the OH adsorption, consequently lowering the reaction barrier of the rate-determining step in HER. Here, our findings are of significance for clarifying the role of Ru in bimetallic catalysts and rational design of more active catalysts for HER/HOR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Understanding the Role of Oxygen Vacancy in Visible–Near-Infrared-Light-Absorbing Ferroelectric Perovskite Oxides Created by Off-Stoichiometry

Recently, the visible or even-to-near-infrared light absorbing perovskite ABO 3 solid state solutions, show promising application in solar cells and multienergy harvesters or sensors by simultaneously introducing transition metal and oxygen vacancies. However, the existence of oxygen vacancies fundamentally causes photoexcited carrier trapping and large leakage current. Therefore, it is still challenging to limit oxygen vacancies while maintaining low bandgap and high ferroelectricity. Here, an efficient charge compensation strategy by finely adjusting the ion ratio on the A-site to obtain an oxygen-vacancy-free relaxer ferroelectric is demonstrated in the system of Na x BiyTiO 3 -BaTi 0.5 Ni 0.5 O 3 , where y > x. It is found that the oxygen-vacancy-free composition still yields strong visible-near-infrared-light-absorbing and enhanced photoresponse, in which the photocurrent density doubles from approximate to 0.16 to approximate to 0.32 mu A cm -2 . A new bandgap tuning mechanism is proposed according to the local structural information of Ni ions obtained via extended X-ray absorption fine structure. Moreover, this work succeeds in establishing the relationship between the concentration of oxygen vacancies and ferroelectric/piezoelectric properties of Na x BiyTiO 3 -BaTi 0.5 Ni 0.5 O 3 . Finally, this research points out a promising route to the material design of bandgap engineered ferroelectrics with controlled defects, which is expected to benefit a wide range of functional energy conversion devices.

36 MATERIALS SCIENCE↗

Pressure-enhanced interplay between lattice, spin, and charge in the mixed perovskite La 2 FeMnO 6

Spin crossover plays a central role in the structural instability, net magnetic moment modification, metallization, and even in superconductivity in corresponding materials. Most reports on the pressure-induced spin crossover with a large volume collapse have so far focused on compounds with a single transition metal. Here we report a comprehensive high-pressure investigation of a mixed Fe-Mn perovskite La 2 FeMnO 6 . Under pressure, the strong coupling between Fe and Mn leads to a combined valence/spin transition: Fe 3+ (S=5/2) → Fe 2 + (S = 0) and Mn 3+ (S = 2) → Mn 4+ (S = 3/2), with an isostructural phase transition. The spin transitions of both Fe and Mn are offset by ~20 GPa of the onset pressure, and the lattice collapse occurs in between. Interestingly, Fe 3+ ion shows an abnormal behavior when it reaches a lower valence state (Fe 2+ ) accompanied by a +0.5 eV energy shift in the Fe K -absorption edge at 15 GPa. This process is associated with the charge-spin-orbital state transition from high spin Fe 3+ to low spin Fe 2+ , caused by the significantly enhanced t 2 g -e g crystal field splitting in the compressed lattice under high pressure. Density functional theory calculations confirm the energy preference of the high-pressure state with charge redistribution accompanied by spin state transition of Fe ions. Moreover, La 2 FeMnO 6 maintains semiconductor behaviors even when the pressure reached 144.5 GPa as evidenced by the electrical transport measurements, despite the huge resistivity decreasing seven orders of magnitude compared with that at ambient pressure. The investigation carried out here demonstrates high flexibility of double perovskites and their good potentials for optimizing the functionality of these materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Single Fe Atom on Hierarchically Porous S, N-Codoped Nanocarbon Derived from Porphyra Enable Boosted Oxygen Catalysis for Rechargeable Zn-Air Batteries

Iron-nitrogen-carbon materials (Fe-N-C) are known for their excellent oxygen reduction reaction (ORR) performance. Unfortunately, they generally show a laggard oxygen evolution reaction (OER) activity, which results in a lethargic charging performance in rechargeable Zn-air batteries. Here porous S-doped Fe-N-C nanosheets are innovatively synthesized utilizing a scalable FeCl 3 -encapsulated-porphyra precursor pyrolysis strategy. The obtained electrocatalyst exhibits ultrahigh ORR activity ( E 1/2 = 0.84 V vs reversible hydrogen electrode) and impressive OER performance ( E j=10 = 1.64 V). The potential gap (Δ E = E j=10 - E 1/2 ) is 0.80 V, outperforming that of most highly active bifunctional electrocatalysts reported to date. Furthermore, the key role of S involved in the atomically dispersed Fe-N x species on the enhanced ORR and OER activities is expounded for the first time by ultrasound-assisted extraction of the exclusive S source (taurine) from porphyra. Moreover, the assembled rechargeable Zn-air battery comprising this bifunctional electrocatalyst exhibits higher power density (225.1 mW cm -2 ) and lower charging-discharging overpotential (1.00 V, 100 mA cm -2 compared to Pt/C + RuO 2 catalyst). Here, the design strategy can expand the utilization of earth-abundant biomaterial-derived catalysts, and the mechanism investigations of S doping on the structure-activity relationship can inspire the progress of other functional electrocatalysts.

25 ENERGY STORAGE↗

Pertechnetate (TcO 4 - ) sequestration from groundwater by cost-effective organoclays and granular activated carbon under oxic environmental conditions

Technetium-99 (Tc-99) is a major risk driver at nuclear power plants and several US Department of Energy (DOE) sites. Pertechnetate (TcO4-), the most common chemical form present in liquid nuclear waste and the environment, displays limited adsorption onto sediments, making it highly mobile and difficult to immobilize. In this work, inexpensive organoclays and granular activated carbon (GAC) were investigated for TcO(4)(- )sequestration from artificial groundwater (AGW). The Tc adsorption capacities were 15 mg/g for organoclays and 25 mg/g for GAC from pH 3-12 AGW under oxic conditions. Competitive NO3- at two orders of magnitude greater concentration than TcO4- reduced the Tc adsorption capacity by only 9-25%. In addition, the adsorbed Tc was effectively desorbed by KI, but not Na2SO4, and the regenerated sorbents retained their Tc removal capacity. X-ray absorption spectroscopy demonstrated that the Tc species bound to the organoclays and GAC was Tc(VII) (i.e., TcO4-), rather than Tc(IV). Thus, the inexpensive organoclays and GAC are highly effective at sequestering Tc-99 in its naturally existing TcO4- without requiring costly reductive systems, which may provide a practical solution for removing (TcO4-)-Tc-99 from environmental systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Origin of Broad Emission Spectra in InP Quantum Dots: Contributions from Structural and Electronic Disorder

The ensemble emission spectra of colloidal InP quantum dots are broader than achievable spectra of cadmium- and lead-based quantum dots, despite similar single-particle line widths and significant efforts invested in the improvement of synthetic protocols. Here, we seek to explain the origin of persistently broad ensemble emission spectra of colloidal InP quantum dots by investigating the nature of the electronic states responsible for luminescence. We identify a correlation between red-shifted emission spectra and anomalous broadening of the excitation spectra of luminescent InP colloids, suggesting a trap-associated emission pathway in highly emissive core shell quantum dots. Time-resolved pump probe experiments find that s are largely untrapped on photoluminescence relevant time scales pointing to emission from recombination of localized holes with free electrons. Two-dimensional electronic spectroscopy on InP quantum dots reveals multiple emissive states and increased electron phonon coupling associated with hole localization. These localized hole states near the valence band edge are hypothesized to arise from incomplete surface passivation and structural disorder associated with lattice defects. We confirm the presence and effect of lattice disorder by X-ray absorption spectroscopy and Raman scattering measurements. Participation of localized electronic states that are associated with various classes of lattice defects gives rise to phonon-coupled defect related emission. These findings explain the origins of the persistently broad emission spectra of colloidal InP quantum dots and suggest future strategies to narrow ensemble emission lines comparable to what is observed for cadmium-based materials.

36 MATERIALS SCIENCE↗

Insights into the Performance Degradation of Oxygen-Type Manganese-Rich Layered Oxide Cathodes for High-Voltage Sodium-Ion Batteries

The cost of batteries is becoming as important as the energy density for large-scale electrochemical energy storage application. Sodium manganese-rich layered oxides (P-type and O-type) are thus one of the promising cathode materials for rechargeable batteries because of the relatively low cost of manganese and sodium. The O-type cathodes are more promising for practical application owing to their high sodium-ion stoichiometry. However, most of these materials suffer from rapid capacity decay during high-voltage cycling. We used synchrotron X-ray probes coupled with electrochemical techniques to disclose the structural evolution of α-NaMnO 2 during solid-state synthesis and electrochemical cycling. During high-voltage cycling, a substantial increase of interfacial microstrain from both stacking faults and Mn cation migration was found to pin down this material’s layered structures and simultaneously block the diffusion pathways of Na + , thus leading to the performance degradation. The findings presented in this work can guide future development of high-performance sodium-ion cathode materials.

25 ENERGY STORAGE↗

Localized Symmetry Breaking for Tuning Thermal Expansion in ScF 3 Nanoscale Frameworks

The local symmetry, beyond the averaged crystallographic structure, tends to bring unu-sual performances. Negative thermal expansion is a peculiar physical property of solids. Here in this paper, we report the delicate design of the localized symmetry breaking to achieve the controllable thermal expansion in ScF 3 nano-scale frameworks. Intriguingly, an isotropic zero thermal expansion is concurrently engineered by localized symmetry breaking, with a remarkably low coefficient of thermal expansion of about +4.0×10-8/K up to 675K. This mechanism is investigated by the joint analysis of atomic pair dis-tribution function of synchrotron X-ray total scattering and extended X-ray absorption fine structure spectra. A localized rhombohedral distortion presumably plays a critical role in stiffening ScF 3 nano-scale frameworks and concomitantly suppressing transverse thermal vibrations of fluorine atoms. This physical scenario is also theoretically corroborated by the extinction of phonon modes with negative Grüneisen parameters in the rhombohedral ScF 3 . The present work opens an untraditional chemical modification to achieve controllable thermal expansion by breaking local symmetries of materials.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗