Engineering topics

Sutter, James K.

Publications and source records attributed to Sutter, James K..

At least 55 records · Page 3

NASA NTRS2002

Development of HVOF Sprayed Erosion/Oxidation Resistant Coatings for Composite Structural Components in Propulsion Systems

Thermally sprayed coatings are being studied and developed as methods of enabling lightweight composites to be used more extensively as structural components in propulsion applications in order to reduce costs and improve efficiency through weight reductions. The primary goal of this work is the development of functionally graded material [FGM] polymer/metal matrix composite coatings to provide improved erosion/oxidation resistance to polyimide-based polymer matrix composite [PMC] substrates. The goal is to grade the coating composition from pure polyimide, similar to the PMC substrate matrix on one side, to 100 % WC-Co on the other. Both step-wise and continuous gradation of the loading of the WC-Co reinforcing phase are being investigated. Details of the coating parameter development will be presented, specifically the high velocity oxy-fuel [HVOF] combustion spraying of pure PMR-11 matrix material and layers of various composition PMR-II/WC-Co blends onto steel and PMR-15 composite substrates. Results of the HVOF process optimization, microstructural characterization, and analysis will be presented. The sprayed coatings were evaluated using standard metallographic techniques - optical and scanning electron microscopy [SEM]. An SEM + electron dispersive spectroscopy [EDS] technique has also been used to confirm retention of the PMR-II component. Results of peel/butt adhesion testing to determine adhesion will also be presented.

Knight, R.↗

NASA NTRS2002

Properties of M40J Carbon/PMR-II-50 Composites Fabricated with Desized and Surface Treated Fibers. Characterization of M40J Desized and Finished Fibers

To increase performance and durability of high temperature composites for potential rocket engine components, it is necessary to optimize wetting and interfacial bonding between high modulus carbon fibers and high temperature polyimide resins. It has been previously demonstrated that the electro-oxidative shear treatments used by fiber manufacturers are not effective on higher modulus fibers that have fewer edge and defect sites in the surface crystallites. In addition, sizings commercially supplied on most carbon fibers are not compatible with polyimides. This study was an extension of prior work characterizing the surface chemistry and energy of high modulus carbon fibers (M40J and M60J, Torray) with typical fluorinated polyimide resins, such as PMR-II-50. A continuous desizing system which utilizes environmentally friendly chemical- mechanical processes was developed for tow level fiber and the processes were optimized based on weight loss behavior, surface elemental composition (XPS) and morphology (FE-SEM) analyses, and residual tow strength of the fiber, and the similar approaches have been applied on carbon fabrics. Both desized and further treated with a reactive finish were investigated for the composite reinforcement. The effects of desizing and/or subsequent surface retreatment on carbon fiber on composite properties and performance including fiber-matrix interfacial mechanical properties, thermal properties and blistering onset behavior will be discussed in this presentation.

Allred, Ronald E.↗

NASA NTRS2002

Evaluation of Graphite Fiber/Polyimide PMCs from Hot Melt versus Solution Prepreg

Carbon fiber reinforced high temperature polymer matrix composites (PMC) have been extensively investigated as potential weight reduction replacements of various metallic components in next generation high performance propulsion rocket engines. The initial phase involves development of comprehensive composite material-process-structure-design-property in-service performance correlations and database, especially for a high stiffness facesheet of various sandwich structures. Overview of the program plan, technical approaches and current multi-team efforts will be presented. During composite fabrication, it was found that the two large volume commercial prepregging methods (hot-melt vs. solution) resulted in considerably different composite cure behavior. Details of the process-induced physical and chemical modifications in the prepregs, their effects on composite processing, and systematic cure cycle optimization studies will be discussed. The combined effects of prepregging method and cure cycle modification on composite properties and isothermal aging performance were also evaluated.

Shin, Eugene E.↗

NASA NTRS2002

Evaluation of Graphite Fiber/Polyimide PMCs from Hot Melt vs Solution Prepreg

Carbon fiber reinforced high temperature polymer matrix composites (PMC) have been extensively investigated as potential weight reduction replacements of various metallic components in next generation high performance propulsion rocket engines. The initial phase involves development of comprehensive composite material-process-structure-design-property-in-service performance correlations and database, especially for a high stiffness facesheet of various sandwich structures. Overview of the program plan, technical approaches and current multi-team efforts will be presented. During composite fabrication, it was found that the two large volume commercial prepregging methods (hot-melt vs. solution) resulted in considerably different composite cure behavior. Details of the process-induced physical and chemical modifications in the prepregs, their effects on composite processing, and systematic cure cycle optimization studies will be discussed. The combined effects of prepregging method and cure cycle modification on composite properties and isothermal aging performance were also evaluated.

Shin, E. Eugene↗

NASA NTRS2000

Erosion Coatings for High-Temperature Polymer Composites: A Collaborative Project With Allison Advanced Development Company

The advantages of replacing metals in aircraft turbine engines with high-temperature polymer matrix composites (PMC's) include weight savings accompanied by strength improvements, reduced part count, and lower manufacturing costs. Successfully integrating high-temperature PMC's into turbine engines requires several long-term characteristics. Resistance to surface erosion is one rarely reported property of PMC's in engine applications because PMC's are generally softer than metals and their erosion resistance suffers. Airflow rates in stationary turbine engine components typically exceed 2.3 kg/sec at elevated temperatures and pressures. In engine applications, as shown in the following photos, the survivability of PMC components is clearly a concern, especially when engine and component life-cycle requirements become longer. Although very few publications regarding the performance of erosion coatings on PMC's are available particularly in high-temperature applications the use of erosion-resistant coatings to significantly reduce wear on metallic substrates is well documented. In this study initiated by the NASA Glenn Research Center at Lewis Field, a low-cost (less than $140/kg) graphite-fiber-reinforced T650 35/PMR 15 sheet-molding compound was investigated with various coatings. This sheet-molding compound has been compression molded into many structurally complicated components, such as shrouds for gas turbine inlet housings and gearboxes. Erosion coatings developed for PMC s in this study consisted of a two-layered system: a bondcoat sprayed onto a cleaned PMC surface, followed by an erosion-resistant, hard topcoat sprayed onto the bondcoat as shown in following photomicrograph. Six erosion coating systems were evaluated for their ability to withstand harsh thermal cycles, erosion resistance (ASTM G76 83 "Standard Practice for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets") using Al2O3, and adhesion to the graphite fiber polyimide composite (ASTM D 4541 95 "Pull Off Strength of Coatings"). Glenn and Allison Advanced Development Company collaborated to optimize erosion coatings for gas turbine fan and compressor applications. All the coating systems survived aggressive thermal cycling without spalling. During erosion tests (see the final photo), the most promising coating systems tested had Cr3C2-NiCr and WC-Co as the hard topcoats. In all cases, these coating systems performed significantly better than that with a TiN hard topcoat. When material depth (thickness) loss is considered, the Cr3C2-NiCr and WC-Co coating systems provided, on average, an erosion resistance 8.5 times greater than that for the uncoated PMR 15/T650 35 composite. Similarly, Cr3C2-NiCr and WC-Co coating systems adhered to the PMC substrate during tensile tests significantly better than systems containing a TiN topcoat. Differences in topcoats of Cr3C2-NiCr and WC-Co were determined by considering issues such as cost and environmental impact. The preferred erosion-resistant coating system for PMR 15/T650 35 has WC-Co as the hard topcoat. This system provides the following benefits in comparison to the coating system with Cr3C2-NiCr topcoat: lower powder material cost (15 to 20 percent), environmentally friendly materials (Cr3C2-NiCr is hazardous), and higher deposition yield (10 to 15 percent), which results in less waste.

Sutter, James K.↗

NASA NTRS1998

Thermomechanical Fatigue Durability of T650-35/PMR-15 Sheet Molding Compound

Although polyimide based composites have been used for many years in a wide variety of elevated temperature applications, very little work has been done to examine the durability and damage behavior under more prototypical thermomechanical fatigue (TMF) loadings. Synergistic effects resulting from simultaneous temperature and load cycling can potentially lead to enhanced, if not unique, damage modes and contribute to a number of nonlinear deformation responses. The goal of this research was to examine the effects of a TMF loading spectrum, representative of a gas turbine engine compressor application, on a polyimide sheet molding compound (SMC). High performance SMCs present alternatives to prepreg forms with great potential for low cost component production through less labor intensive, more easily automated manufacturing. To examine the issues involved with TMF, a detailed experimental investigation was conducted to characterize the durability of a T650-35/PMR-15 SMC subjected to TMF mission cycle loadings. Fatigue damage progression was tracked through macroscopic deformation and elastic stiffness. Additional properties, such as the glass transition temperature (T(sub g) and dynamic mechanical properties were examined. The fiber distribution orientation was also characterized through a detailed quantitative image analysis. Damage tolerance was quantified on the basis of residual static tensile properties after a prescribed number of TMF missions. Detailed microstructural examinations were conducted using optical and scanning electron microscopy to characterize the local damage. The imposed baseline TMF missions had only a modest impact on inducing fatigue damage with no statistically significant degradation occurring in the measured macroscopic properties. Microstructural damage was, however, observed subsequent to 100 h of TMF cycling which consisted primarily of fiber debonding and transverse cracking local to predominantly transverse fiber bundles. The TMF loadings did introduce creep related effects (strain accumulation) which led to rupture in some of the more aggressive stress scenarios examined. In some cases this creep behavior occurred at temperatures in excess of 150 C below commonly cited values for T(sub g). Thermomechanical exploratory creep tests revealed that the SMC was subject to time dependent deformation at stress/temperature thresholds of 150 MPa/230 C and 170 MPa/180 C.

Castelli, Michael G.↗

NASA NTRS1998

Low-Cost Manufacturing of High- Temperature Polymer Composites

Major goals of NASA and the Integrated High Performance Turbine Engine Technology (IHPTET) initiative include improvements in the affordability of propulsion systems, significant increases in the thrust/weight ratio, and increases in the temperature capability of components of gas turbine engines. Members of NASA Lewis Research Center's HITEMP project worked cooperatively with Allison Advanced Development Corporation to develop a manufacturing method to produce low-cost components for gas turbine engines. Affordability for these polymer composites is defined by the savings in acquisition and life-cycle costs associated with engine weight reduction. To lower engine component costs, the Lewis/Allison team focused on chopped graphite fiber/polyimide resin composites. The high-temperature polyimide resin chosen, PMR-II-50, was developed at NASA Lewis.

Sutter, James K.↗

NASA NTRS1997

Compressor Case Manufactured Using High-Temperature Polyimides

High-temperature polymer composites (PMC's) offer lighter weight and higher specific strengths than titanium alloys for advanced aircraft engine applications-especially in fan and compressor components, where temperatures do not exceed 550 F (288 C). VCAP, a polyimide resin developed at the NASA Lewis Research Center, was filament wound at Lincoln Composites in Lincoln, Nebraska, with graphite and glass fibers to produce a lightweight compressor case for an Integrated High Performance Turbine Engine Technology (IHPTET) engine. This engine application requires a PMC that can withstand air pressures (60 psi) and temperatures exceeding the degradation limits of other high-temperature polyimides, such as PMR-15.

Sutter, James K.↗

NASA NTRS1995

Statistical Design in Isothermal Aging of Polyimide Resins

Recent developments in research on polyimides for high temperature applications have led to the synthesis of many new polymers. Among the criteria that determines their thermal oxidative stability, isothermal aging is one of the most important. Isothermal aging studies require that many experimental factors are controlled to provide accurate results. In this article we describe a statistical plan that compares the isothermal stability of several polyimide resins, while minimizing the variations inherent in high-temperature aging studies.

Sutter, James K.↗

NASA NTRS1995

High Modulus and High T(sub g) Thermally Stable Polymers from p-Ethynyl-Terminated Rigid-Rod Monomers

Novel p-ethynyl-substituted rigid rod monomers were studied by pressure Differential Scanning Calorimetry (DSC), ThermoGravimetric Analysis (TGA), IsothermoGravimetric Analysis (IGA), and TGA-IR. These monomers, 4,4'-bis(((4-ethynylphenyl)carbonyl)oxy)biphenyl, designated 1, 1,5-bis-(((4-ethynylphenyl)carbonyl)oxy)naphthalene, designated 2, and bis(4-ethynylphenyl)pyromellitimide, designated 3, were polymerized in the solid state. Thermal polymerization in N2 or air produced highly cross-linked resins with polymerization exotherms centered between 212 and 276 C. The (delta)H's of polymerization of these resins in air were found to be double those in N2. When monomers 1 and 2 were heated in air from 23 to 750 C at 10 C/min, the main decomposition product was carbon dioxide, evolving at a maximum rate between 500 and 600 C; water was also detected as a decomposition product. Void-free neat resin moldings, designated lp to 3p, were made by compression molding the monomers and then heating them. The resulting polymers were highly cross-linked, and their glass transition temperatures (T(sub g)) were much higher than their polymerization temperatures. Using ThermoMechanical Analysis (TMA), we found that polymers lp to 3p had T(sub g)'s of 422, 329, and 380 C, respectively. The thermal and thermooxidative stabilities improved when lp to 3p were postcured in N2 (the postcured polymers were designated 1pp to 3pp). The Linear Thermal Expansions (LTE) for lp and 3p were 1% between 23 and 420 C. Using rheological analysis, we could not clearly detect the T(sub g)'s of lp to 3p because their moduli dropped only slightly between 23 and 490 C and the changes in tan beta were very low. Because of high cross-link density, their moduli changed little as the resins went from a glassy to a rubbery state. Their shear storage moduli in air ranged from 0.82 (3p, 3pp) to 1.6 GPa (lpp) at 23 C, from 0.16 (2p) to 0.7GPa(lpp) at 380 C, and from 0.18(lpp)to 0.6GPa(2p) at 490 C. Finally, these novel-p-ethynyl polymers exhibited an excellent combination of high T(sub g), low LTE, and high thermooxidative stability. Most notably, 3pp lost only 3% of its initial weight when it was aged for 500 h at 288 C in air.

Melissaris, Anastasios P.↗

NASA NTRS1994

An NDE Approach for Characterizing Quality Problems in Polymer Matrix Composites

Polymer matrix composite (PMC) materials are periodically identified appearing optically uniform but containing a higher than normal level of global nonuniformity as indicated from preliminary ultrasonic scanning. One such panel was thoroughly examined by nondestructive (NDE) and destructive methods to quantitatively characterize the nonuniformity. The NDE analysis of the panel was complicated by the fact that the panel was not uniformly thick. Mapping of ultrasonic velocity across a region of the panel in conjunction with an error analysis was necessary to (1) characterize properly the porosity gradient that was discovered during destructive analyses and (2) account for the thickness variation effects. Based on this study, a plan for future NDE characterization of PMC's is presented to the PMC community.

Roth, Don J.↗

NASA NTRS1994

Easily Processable High-Temperature Polyimide

Polymerization without volatile gases leads to high-quality resins. N-CYCAP (amiNe substituted CYClophane Addition Polyimide) is thermoset polyimide developed containing 4-amino{2.2}paracyclophane as end cap. Current improvements in synthesis of end cap include increasing yield to 60 percent overall and decreasing manufacturing time by simplifying synthetic procedure. Enables large-scale production and increases viability of cyclophane end caps for polymers for high-temperature applications. In comparison with neat resin moldings and composite matrix resins made of PMR-II-50, those made of N-CYCAP polymers found to be processable with lower void content and higher thermo-oxidative stability.

Sutter, James K.↗

NASA NTRS1993

Protective coatings for high-temperature polymer matrix composites

Plasma-enhanced chemical vapor deposition was used to deposit silicon nitride on graphite-fiber-reinforced polyimide composites to protect against oxidation at elevated temperatures. The adhesion and integrity of the coating were evaluated by isothermal aging (371 C for 500 hr) and thermal cycling. The amorphous silicon nitride (a-SiN:H) coating could withstand stresses ranging from approximately 0.18 GPa (tensile) to -1.6 GPa (compressive) and provided a 30 to 80 percent reduction in oxidation-induced weight loss. The major factor influencing the effectiveness of a-SiN:H as a barrier coating against oxidation is the surface finish of the polymer composite.

Harding, David R.↗

NASA NTRS1992

Benzonorbornadiene end caps for PMR resins

Several ortho-disubstituted benzonorbornadiene derivatives are described. These molecules contain acid, ester, or anhydride functionality permitting their use as end caps in PMR (polymerization of monomer reactants) polyimide systems. The replacement of the currently used norbornenyl end caps with benzonorbornadienyl end caps affords resins of increased aromatic content. It also allows evaluation of some mechanistic aspects of PMR cross-linking. Initial testing of N-phenylimide model compounds and of actual resin formulations using the benzonorbornadienyl end cap reveals that they undergo efficient thermal crosslinking to give oligomers with physical properties and thermal stability comparable to commercial norbornene-end-capped PMR systems.

Panigot, Michael J.↗

NASA NTRS1992

Lower temperature curing thermoset polyimides utilizing a substituted norbornene endcap

Methoxycarbonyl bridgehead substituted nadic diacid monomethyl ester, when used as an endcapping monomer, lowered the cure temperature of thermoset PMR polyimides without seriously affecting other desirable properties, such as glass transition temperature and thermal oxidative stability. The C-13 CP/MAS NMR of model compounds was used to follow the cure of resin systems using both the unmodified nadic endcap and the methoxycarbonyl-substituted endcap. Rheological analysis and differential scanning calorimetry DSC also provided evidence for the lower curing nature of the substituted endcap. Two regioisomers of the bridgehead-substituted endcap were isolated, and their chemical structures were elucidated by X-ray crystallography. The model compound and molecular modeling studies conducted ruled out the possibility of regioisomeric imide formation in the substituted endcaps.

Waters, John F.↗

NASA NTRS1991

Long term isothermal aging and thermal analysis of N-CYCAP polyimides

The N-CYCAP polyimides utilize a (2,2) paracyclophane endcap that polymerizes and does not generate volatile gases during the cure process. These polyimides have both high glass temperatures (390 C) and an onset of decomposition in air of 560 C. Thermal oxidative stability (TOS) weight loss studies show that replacing 25 percent by weight of the paraphenylene diamine in the polymer backbone with metaphenylene diamine improves the weight loss characteristics. N-CYCAP neat resin samples performed better than PMR-II-50 when exposed at 343 and 371 C in air for up to 1000 hours. Preliminary composite studies show that both PMR-II-50 and N-CYCAP have better thermal stability when fabricated on T-40R. Higher isothermal aging temperatures of longer aging times are needed to determine the differences in TOS between composite samples of PMR-II-50 and N-CYCAP polyimides.

Sutter, James K.↗

NASA NTRS1991

Addition Curing Thermosets Endcapped with 4-Amino (2.2) Paracyclophane

A new family of addition curing polyimides were prepared that contained 4-amino (2.2)-paracyclophane as the endcap. An improved synthesis of the endcap 4-amino-(2.2) cyclophane was accomplished increasing the yield to 60 percent and simplifying the procedure. DSC and rheological analysis of endcapped polyimide oligomers confirmed that the onset for polymerization of the ethylene bridge was 250 C. C-13 CP/MAS NMR was used to determine the structural changes of the oligomers after thermal treatment. The cyclophane capped polyimides were successfully compression molded to form void free neat resin specimens. Tg's as high as 353 C were obtained by thermomechanical analysis for postcured samples. Preliminary thermal stability studies suggest that these resins have a high onset of decomposition ranging from 549 to 567 C.

Waters, John F.↗

NASA NTRS1990

Characterization of M40J Desized and Finished Fibers

A viewgraph presentation on desized and finished M40J carbon fibers shown. The topics include: 1) Program Goals and Prior Year Results Summary; 2) Continuous Desizing and Finishing System Development; 3) Characterizzation of Desized and Finished M40J Carbon Fibers and 4) Conclusions and Future Work.

Allred, Ronald E.↗