Tallerico, Thomas F. | Search NASA

NASA NTRS2019

Design of a Magnetic Gear for NASA's Vertical Lift Quadrotor Concept Vehicle

Magnetic gears are an attractive alternative to mechanical gears for electrified aircraft drive systems due to their ability to transmit torque without mechanical tooth contact. Consequently, magnetic gears enable electrified aircraft to take advantage of the benefits of gearing without introducing most of the contact-related reliability concerns associated with mechanical gearing. Magnetic gears however, have not been shown to match the specific torque (torque/mass) and efficiency of their mechanical counterparts in an aerospace application to date. In this paper, the design of a concentric magnetic gear for a personal air transport NASA reference vehicle is presented to demonstrate the feasibility of a magnetic gear for aerospace applications.

Tallerico, Thomas F.↗

NASA NTRS2019

Electromagnetic Mass and Efficiency of Magnetic Gears for Electrified Aircraft

Magnetic gears are currently being developed for use in a variety of industries such as wind and automotive, because of their higher reliability and lower maintenance cost than their mechanical counterparts. The bulk of magnetic gear development to date has focused on maximizing the technology's volumetric torque density. In contrast, the primary performance metrics for an aircraft's gear box are its mass and efficiency. To that end this paper presents a study of the achievable electromagnetic specific torque and efficiency of concentric magnetic gears. NASA's second magnetic gear prototype is used as the baseline for this study. Achievable electromagnetic specific torque and efficiency trends are presented with respect to higher level design variables such as gear ratio and radius.

Tallerico, Thomas F.↗

NASA NTRS2019

Progress Toward the Critical Design of the Superconducting Rotor for NASA's 1.4 MW High-Efficiency Electric Machine

NASA Glenn Research Center is developing a 1.4 MW high-efficiency electric machine for future electrified aircraft to reduce energy consumption, emissions, and noise. This wound-field, synchronous machine employs a self-cooled, superconducting rotor to achieve excellent specific power and efficiency. This paper presents the progress made over the past year toward a critical design of the superconducting rotor, including refined analysis and risk reduction testing on prototype superconducting coils. A 3D finite element model of the rotor is developed to simulate the combined loading imposed by the initial cool down of the rotor from room temperature to cryogenic temperature and the subsequent rotation of the rotor up to the design speed. The model is evaluated to better predict the stress state in the critical components and the reduction in physical gap between the stator and rotor due to the resulting radial deflections. This model includes an enhanced model of the superconducting coil that considers the coil as an assembly of four individual coil layers. An improved coil fabrication process is described in detail. Two sub-scale test coils are fabricated and then tested under repeated thermal cycling between room temperature and liquid nitrogen temperature (77 K). It is demonstrated that the proposed coil fabrication procedure can produce no-insulation, high temperature superconducting coils that can survive several thermal cycles without apparent degradation.

electric machines↗

NASA NTRS2019

Ultrasonic Gear Steel Fatigue at NASA

Gear tooth bending fatigue life is one of the main drivers of rotorcraft gear box weight and maintenance cost. Depending on rotorcraft gearbox speed, 10,000 flight hours can easily mean reaching gear tooth bending fatigue cycles in the 10^10 cycle regime. Traditionally gear fatigue life in the 10^10 cycle regime is estimated based on empirical correction factors applied to the traditional fatigue limit of 10^7 cycles. In order to improve on this method of life prediction, enable better gear box design, and reduce gear box maintenance cost, NASA has started an ultrasonic gear steel fatigue program to quantify the 10^10 life of gear steels. Ultrasonic fatigue testing makes use of piezo electric actuators and resonance to generate stress-strain cycles at 20 kHz. The ability to test gear steals at 20 kHz reduces test time for 10^10 cycles from roughly 16 years with traditional 20 Hz testing to 6 days. In this presentation, the establishment of NASA's ultrasonic test capability, results to date, and future testing plans will be discussed.

Tallerico, Thomas F.↗

NASA NTRS2019

X-57 Mod 2 Motor Thermal Analysis

This work covers the refinement of thermal models from design estimates to actual fabricated performance. Matching the experimental data of the first fully electrified version of the X-57 Maxwell experimental vehicle requires high fidelity thermal analysis to sufficiently capture the electric motor and inverter temperature profiles. Qualification test data of the motors and inverters is used to validate finite element analysis models used to simulate thermal performance over mission transients. An additional thermal-hydraulic models is used to estimate flow characteristics through the propulsor nacelle and component heat sinks. After calibration of the higher order models, overall component sizing and peak temperature constraints can be distilled to reduced order models, to improve modelflexibility and utility.

Chin, Jeffrey C.↗

NASA NTRS2019

Lessons Learned in Fabrication of a High-Specific-Torque Concentric Magnetic Gear

Magnetic gearing is being investigated at NASA as a replacement to conventional mechanical gearing in aerospace applications. Some potential benefits of magnetic gears over mechanical gearing are torque transmission without mechanical contact, decreased transmission noise, and no required lubrication. However, in order to be a viable alternative for aerospace applications, magnetic gearing must be shown to provide high enough specific torque (torque per unit mass). NASA's second magnetic gearing prototype (PT-2) was able to achieve promising specific torque on par with low torque mechanical gearboxes. This work will briefly review the electromagnetic and structural design of PT-2, provide detailed information on fabrication and assembly, examine build errors, walk through rebuild efforts to improve operation, and conclude with remarks on build difficulties and opportunities for improvement in future prototypes.

Magnetic Gearing↗

NASA NTRS2019

Dynamic Testing of a High-Specific-Torque Concentric Magnetic Gear

This paper presents initial measurements of the efficiency of NASA's 2nd magnetic gear prototype. A detailed discussion of the test rig's design and capabilities was presented, along with a thorough uncertainty analysis. The reported uncertainties are 95% confidence intervals that include the effects of temperature and parasitic loads. The prototype's response was measured at output speeds between 124 rpm and 744 rpm for a controlled output torque of 10 Nm (8% of the prototype's maximum torque). After correcting for tare losses, the prototype's efficiency was found to decrease from 90.0% to 83.0% as speed increased. If the efficiency is extrapolated to a typical operating condition (85% of maximum torque) using the good assumption that energy loss is approximately independent of the transmitted torque, the expected efficiency would be 99.0% to 98.4%, which exceeds the state of the art for these speeds.

magnetic gears↗

NASA NTRS2018

NASA's Magnetic Gearing Research for Electrified Aircraft Propulsion

This paper presents an overview of the magnetic gearing research being conducted at NASA. First, the research is motivated through an in-depth discussion of the Agency-level aeronautics vision, the benefit of geared drivetrains, the barriers to applying mechanical gears in future aircraft concepts with electrified aircraft propulsion, and the characteristics of magnetic gears that allow them to overcome said barriers. Next, the principles of operation and current limitations of magnetic gears are discussed in the context of future electrified aircraft. Then, the authors' vision for the magnetic gearing research that will be needed to enable the next generation of electrified aircraft is presented. Lastly, the recent and ongoing magnetic gearing research at NASA is described, with a focus on the development and capabilities of a new rotating test rig and new static measurements of an in-house prototype. Results and lessons learned thus far are summarized.

drive systems↗

NASA NTRS2018

Design, Fabrication, and Critical Current Testing of No-Insulation Superconducting Rotor Coils for NASA's High-Efficiency Megawatt Motor

NASA Glenn Research Center is developing a 1.4~MW high-efficiency electric machine for future electrified aircraft to reduce energy consumption, emissions, and noise. This wound-field, synchronous machine employs a self-cooled, superconducting rotor to achieve excellent specific power and efficiency. This paper discusses the fabrication of the no-insulation high temperature superconducting (HTS) coils and presents the lessons learned. The process is compared to the fabrication of conventionally insulated HTS coils. Testing of the coils' critical current at liquid nitrogen temperature is also presented. The influence of thermal cycling on the critical current and n-value is studied.

Scheidler, Justin J.↗

NASA NTRS2018

Design, Fabrication, and Critical Current Testing of No-Insulation Superconducting Rotor Coils for NASA's 1.4 MW High-Efficiency Megawatt Motor

NASA Glenn Research Center is developing a 1.4 MW high-efficiency electric machine for future electrified aircraft to reduce energy consumption, emissions, and noise. This wound-field, synchronous machine employs a self-cooled, superconducting rotor to achieve excellent specific power and efficiency. This paper discusses the design and fabrication of the no-insulation high temperature superconducting (HTS) rotor coils and compares them to conventionally insulated HTS coils. Two sub-scale test coils with epoxy on only one axial face were fabricated. Critical current testing of the coils at 77 K and self field was conducted to study the influence of thermal cycling on their critical current and n-value. After two or four aggressive thermal cycles between 77 K and about 278 K (5 degree C), the critical current and n-value were nearly unchanged, indicating very little to no degradation.

electric aircraft propulsion↗

NASA NTRS2018

NASA's Magnetic Gearing Research for Electrified Aircraft Propulsion

This paper presents an overview of the magnetic gearing research being conducted at NASA. First, the research is motivated through an in-depth discussion of the Agency-level aeronautics vision, the benefit of geared drivetrains, the barriers to applying mechanical gears in future aircraft concepts with electrified aircraft propulsion, and the characteristics of magnetic gears that allow them to overcome said barriers. Next, the principles of operation and current limitations of magnetic gears are discussed in the context of future electrified aircraft. Then, the authors' vision for the magnetic gearing research that will be needed to enable the next generation of electrified aircraft is presented. Lastly, the recent and ongoing magnetic gearing research at NASA is described, with a focus on the development and capabilities of a new rotating test rig and new static measurements of an in-house prototype. Results and lessons learned thus far are summarized.

geared motors↗

NASA NTRS2018

Magnetic Gearing Research at NASA

Magnetic gearing is an alternative to mechanical gearing, where torque is transferred through magnetic force as opposed to contact force. The technology has the potential to be used in aircraft applications, without the lubrication, noise, and maintenance issues that can exist with mechanical gearing. Initial design and prototype development work was done at NASA to create a foundational understanding of the technology and the factors that influence its specific torque. The specific torque achieved through design optimization was found to be less than that of high-torque mechanical aircraft transmissions, but may be comparable to that of lower torque mechanical transmissions for electrified vertical takeoff and landing aircraft. The lessons learned from NASA's initial technology development and the direction of NASA's future work in field are discussed.

propulsion systems↗