Engineering topics

Vackel, Andrew

Publications and source records attributed to Vackel, Andrew.

11 records

DOE OSTI2024

Effects of Plume Targeted Cooling on Residual Stress in Controlled Atmosphere Plasma Sprayed Coatings

Thermal spray processes can benefit from cooling to maintain substrate temper, reduce processing times, and manage thermally induced residual stresses. “Plume quenching” is a plume-targeted cooling technique which has been shown to reduce substrate temperatures by redirection of hot plume gases using a lateral argon curtain injected into the plume, while limiting interaction with the substrate or affecting coating properties. Here, this study explores the use of this technique for residual stress management by reducing the thermally driven component in nickel and tantalum coatings on titanium and aluminum substrates. The in-situ residual stress profiles were measured for all substrate and coating pairings during spraying and cooling, and the deposition and thermal stresses recorded. For substrate and coating pairings where the predominant component of residual stress was thermal (driven by a large difference in coefficient of thermal expansion, Δα, between coating and substrate), plume quenching reduced both the thermal stress and the final stress state of the coating. This was seen primarily in tantalum on aluminum coatings where the Δα was -17 × 10 -6 /°C, and thermal stress was reduced by 7.5% and 22.4% for the plume quenching rates of 50 and 100 slpm, respectively.

42 ENGINEERING↗

DOE OSTI2023

Shock state distributions in porous tantalum and characterization with multipoint velocimetry

Heterogenous materials under shock compression can be expected to reach different shock states throughout the material according to local differences in microstructure and the history of wave propagation. Here, in this work, a compact, multiple-beam focusing optic assembly is used with high-speed velocimetry to interrogate the shock response of porous tantalum films prepared through thermal-spray deposition. The distribution of particle velocities across a shocked interface is compared to results obtained using a set of defocused interferometric beams that sampled the shock response over larger areas. The two methods produced velocity distributions along the shock plateau with the same mean, while a larger variance was measured with narrower beams. The finding was replicated using three-dimensional, mesoscopically resolved hydrodynamics simulations of solid tantalum with a pore structure mimicking statistical attributes of the material and accounting for radial divergence of the beams, with agreement across several impact velocities. Accounting for pore morphology in the simulations was found to be necessary for replicating the rise time of the shock plateau. The validated simulations were then used to show that while the average velocity along the shock plateau could be determined accurately with only a few interferometric beams, accurately determining the width of the velocity distribution, which here was approximately Gaussian, required a beam dimension much smaller than the spatial correlation lengthscale of the velocity field, here by a factor of ∼30×, with implications for the study of other porous materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Quantifying Pore Morphology in Spray-Formed Tantalum Using X-ray Micro-computed Tomography

In order to establish quantitative process–structure–property relationships in thermal spray coatings, a robust framework for defining (micro)structural characteristics is needed. Here, we present a quantitative characterization of the three-dimensional morphology of porosity in spray-formed tantalum samples based on high-resolution X-ray micro-computed tomography. Using synchrotron facilities, we acquired dozens of high-resolution scans, enabling a statistically meaningful comparison across multiple samples, different regions within samples, and spray processes. We quantify the spatial distribution, size, and topology of porous inclusions, with a significant focus on variability across samples and different spray processes (plasma and cold sprayed), as well as sensitivity to image segmentation and resolution. Based on a typical segmentation, we report porosities ranging from 0.9 to 1.7 pct for all samples tested, with significant sensitivity due to image segmentation resulting in estimates as low as 0.6 pct and as high as 4.8 pct. For the complex pore space morphology observed in these materials, we argue that a conventional analysis based on identifying individual pores is not well suited, and propose an alternative approach based on morphological metrics with a rich history in porous media literature, such as spatial correlations, local pore thickness, and scale-dependent sub-sampling. Spatial correlations indicate anisotropic splat structures, but only mildly anisotropic pores. Various measures of pore size show a wide distribution of sizes, ranging from sub-micron to 10-micron length scales. Scale-dependent variations in porosity suggest that representative volumes of several hundred microns are required for convergence of morphological metrics, with larger volumes for cold-spray materials. This work provides a robust quantitative basis for describing three-dimensional pore structure in thermal spray coatings.

36 MATERIALS SCIENCE↗

DOE OSTI2023