Search NASA⌕ Search

Engineering topics

Veith, Gabriel M.

Publications and source records attributed to Veith, Gabriel M..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Direct Prelithiation of Silicon-Based Composite Electrodes via Island-like Thermal Evaporation

Irreversible losses of Li during solid electrolyte interface (SEI) conditioning is a key contributor to the lower specific capacities observed in silicon-containing Li-ion batteries. Herein, thermal evaporation of between 1 and 20 µm of Li onto Si-based composite anodes has been investigated as a prelithiation method to account for such losses. To account for mechanical strain caused by Li-Si alloying during the deposition, a stainless-steel mesh is applied to the electrodes before prelithiation to form “island-like” deposition on the electrode surface. The open circuit potential was also found to decrease as a function of increased Li evaporation, consistent with the potentials of electrochemically prepared LixSi alloys. Prelithiating to account for irreversible Li losses to SEI formation resulted in full cells with a 15.8% increase in initial coulombic efficiency and a 47.8% reduction in irreversible capacity loss after SEI formation cycling. Subsequent C/3 cycling showed up to a 62.9% increase in specific capacity in prelithiated cells. X-ray photoelectron spectroscopy (XPS) revealed differences in the SEI composition that was formed by electrochemical cycling and reactively formed in prelithiated cells upon exposure to Gen2 + 3% FEC electrolyte. The reactively formed SEI from the spontaneous reaction with lithiated silicon was carbonate-rich while the electrochemical SEI formation showed significantly more LiPFx species, which could play a role in overall cycling performance.

Musgrove, Amanda↗
DOE OSTI2024

Flux Synthesis of A-site Disordered Perovskite La 0.5 M 0.5 TiO 3 (M$=$Li, Na, K) Nanorods Tailored for Solid Composite Electrolytes

Inorganic fillers play an important role in improving the ionic conductivity of solid composite electrolytes (SCEs) for Li-ion batteries. Among inorganic fillers, perovskite-type lithium lanthanum titanate (LLTO) stands out for its high bulk Li + conductivity on the order of 10 -3 S cm -1 at room temperature. According to a literature survey, the optimal LLTO filler should possess the following characteristics: i) a single-crystal structure to minimize grain boundaries; ii) a small particle size to increase the filler/polymer interface area; iii) a 1D morphology for efficient interface channels; and iv) cubic symmetry to facilitate rapid bulk Li + diffusion within the filler. However, the synthesis of single crystal, 1D LLTO nanomaterials with cubic symmetry is challenging. Herein, a flux strategy is developed to synthesize La 0.5 M 0.5 TiO 3 (LMTO, M$=$Li, Na, and K) single-crystal nanorods with an A-site-disordered, cubic perovskite phase. The flux media promotes the oriented growth of nanorods, prevents nanorods from sintering, and provides multiple alkali metal ion doping at M sites to stabilize the cubic phase. SCEs compositing the Li + -conducting LMTO nanorods as fillers and poly[vinylene carbonate- co -lithium sulfonyl(trifluoromethane sulfonyl)imide methacrylate] matrix exhibit more than twice the conductivity of the neat polymer electrolyte (30.6 vs 14.0 µS cm -1 at 303 K).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Mitigating Calendar Aging in Si-NMC Batteries with Advanced Dual-Salt Glyme Electrolytes

In addressing the critical challenge of calendar aging in silicon (Si)-based lithium-ion batteries, this study introduces a groundbreaking strategy utilizing glyme-type dual-salt electrolytes (lithium bis(trifluoromethanesulfonyl)imide [LiTFSI] and lithium difluoro(oxalato)borate [LiDFOB]). These electrolytes are demonstrated to significantly mitigate parasitic reactions and capacity loss in Si-NMC (lithium nickel manganese cobalt oxide) full cells, especially when compared with traditional carbonate-based electrolytes. Further, our exhaustive mechanistic analysis reveals that such electrolytes not only preserve the integrity of the Si anode but also improve the cathode/electrolyte interphases (CEI) through the formation of a conformal coating on the high-voltage cathode surface. This dual-salt approach, enhanced by the addition of a phosphate additive, effectively decelerates calendar aging, marking a substantial advance in the quest for durable and reliable Si-based energy storage technologies. The findings underscore the vital role of electrolyte composition in extending the calendar life of Si batteries, offering an alternative avenue toward maximizing the performance and longevity of next-generation Li-Si batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Chemo-Mechanical Instabilities in Lithium Cobalt Oxide at Higher State-Of-Charge in Li-Ion Batteries

Transition metal oxide cathodes are widely used in commercial Li-ion batteries. However, their practical charge capacity is limited due to severe chemo-mechanical instabilities at higher charge voltage, and state-of-charge condition. Here, in situ stress and strain measurements were synchronized to probe mechanical deformations in the lithium cobalt oxide (LCO) cathode via a multi-beam stress sensor and digital image correlation, respectively. In situ mechanical measurements revealed how Li removal from the electrode structure induces deformations on the LCO composite cathodes during cycling. The structure and morphology of the LCO cathodes were further investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) studies. Two distinct electrochemical and mechanical behaviors were identified when the LCO was charged up to 4.65 V. The LCO undergoes a compressive stress generation when charged up to 4.2 V and surface fractures on the LCO particles were detected by SEM. LCO cathode experienced significantly large contractions (negative strains) when charged up to 4.65 V, where intergranular crack formation and phase transformation were detected on the LCO particles via SEM and XRD, respectively. Overall, the study bridges complicated structural deformations with in situ analysis of mechanical degradations in LCO cathodes charged at higher voltages. The correlation is vital to understanding instability mechanisms in transition metal oxides at high voltages for alkali metal ion batteries.

higher state-of-charge↗
DOE OSTI2024

Elucidating the local structure of Li 1+ x Al x Ti 2– x (PO 4 ) 3 and Li 3 Al x Ti 2– x (PO 4 ) 3 ( x = 0, 0.3) via total scattering

Li 1+x Al x Ti 2–x (PO 4 ) 3 (LATP) and Li 3 Al x Ti 2–x (PO 4 ) 3 (x = 0, 0.3) are promising candidates in all-solid-state batteries due to their high room temperature conductivity of 10 –3 S cm –1 and air- and moisture-stability. They also exhibit unusual thermal expansion properties, with Li 1+x Al x Ti 2–x (PO 4 ) 3 showing near-zero thermal expansion along the a axis while Li 3 Al x Ti 2–x (PO 4 ) 3 exhibits polynomial positive thermal expansion along the a axis and polynomial negative thermal expansion along the c axis. A crucial component to understanding these properties is understanding the local structure. Total scattering is a powerful analytical technique as it provides information on the long-range, average structure as well as the local structure. Here, we report the first X-ray and neutron total scattering experiments performed on Li 1+x Al x Ti 2–x (PO 4 ) 3 and Li 3 Al x Ti 2–x (PO 4 ) 3 (x = 0, 0.3). We show that the PO 4 and TiO 6 polyhedra experience very little expansion of the P/Ti–O bonds up to 800 °C, nor is there much expansion when the Li content increases significantly. The minor thermal expansion of the nearest-neighbor bonds of the polyhedra is revealed to be the reason behind the unusual thermal expansion properties, causing the near-zero thermal expansion along a in Li 1+x Al x Ti 2–x (PO 4 ) 3 and moving as whole units in Li 3 Al x Ti 2–x (PO 4 ) 3 . The structural robustness of the framework is also the reason for the increased conductivity as Li content increases, as the framework remains undistorted as Li content increases, permitting Li-ion mobility as the number of charge carriers increases. Finally, this suggests that phosphate-based framework materials beyond LATP would also be a good material space to explore for new Li-ion (and other ion-) conducting materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Effects of Al concentration on the structure and conductivity of lithium lanthanum zirconium oxide

Cubic Li 7-3x Al x La 3 Zr 2 O 12 (LLZO) is a promising, next-generation solid electrolyte due to its stability with Li-metal and high bulk conductivity (~1 mS cm -1 ). However, the source of the high conductivity is not completely understood. In this work, we address this key knowledge gap through the integration of elemental analysis, neutron diffraction sensitive to Li and O atoms, and impedance spectroscopy to understand the structure–property correlations for LLZO. We show the metal–oxygen framework structure remains constant with variation in Al substitution, resulting in a constant activation energy of ~0.35 eV and little effect on the bulk conductivity. Instead, Li concentration, Al blocking and trapping of mobile defects, and Li–Li nearest neighbor interactions largely control the Al substituted LLZO bulk conductivity, resulting in decreases from 0.73 to 0.22 mS cm -1 as the Al concentration increases from 0.17 to 0.32 mol. These results differ from those of Ta substituted LLZO, where the framework structure and Li–Li site distances play large roles in controlling the conductivity. The increased understanding of the controlling factors of conductivity allows for greater ability to tailor the design of and substitution into the LLZO structure for improved conductivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Corrosion and Enhanced Hydrogen Evolution in Electrochemical Reduction of Ammonium Carbamate on Transition Metal Surfaces

Experiments and theory are combined to search for catalyst activity and stability descriptors for the direct reactive capture and conversion (RCC) of CO 2 in ammonia capture solutions using Cu, Ag, Au, Sn, and Ti electrodes. Two major phenomena emerge in RCC that are not predominant in the electrochemical CO 2 reduction (CO 2 R) reaction, namely, the rapid corrosion and restructuring of the catalyst in the presence of the CO 2 -ammonia adducts and the promotion of the competing hydrogen evolution reaction (HER). The prevalence of HER in RCC is correlated to the electrostatic attraction of the protonated amine to the electrode and the repulsion of the captured CO 2 , using the potential of zero charge (PZC). The stability of catalysts under RCC conditions is a function of the applied potential and cannot be readily predicted using binding energy descriptors commonly used in the prediction of CO 2 R activity. Finally, a direct correlation between calculated binding energies of CO 2 R intermediates, atomic oxygen, hydrogen, and ammonia and the activity and stability of transition metals for RCC cannot be found, highlighting the need for descriptors beyond those known for CO 2 R.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Inactive Overhang in Silicon Anodes

Li-ion batteries contain excess anode area to improve manufacturability and prevent Li plating. These overhang areas in graphite electrodes are active but experience decreased Li + flux during cycling. Over time, the overhang and the anode portions directly opposite to the cathode can exchange Li + , driven by differences in local electrical potential across the electrode, which artificially inflates or decreases the measured cell capacity. Here, we show that lithiation of the overhang is less likely to happen in silicon anodes paired with layered oxide cathodes. The large voltage hysteresis of silicon creates a lower driving force for Li + exchange as lithium ions transit into the overhang, rendering this exchange highly inefficient. For crystalline Si particles, Li + storage at the overhang is prohibitive, because the low potential required for the initial lithiation can act as thermodynamic barrier for this exchange. We use micro-Raman spectroscopy to demonstrate that crystalline Si particles at the overhang are never lithiated even after cell storage at 45 °C for four months. Because the anode overhang can affect the forecasting of cell life, cells using silicon anodes may require different methodologies for life estimation compared to those used for traditional graphite-based Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Elucidating the Role of Carbon Conductive Additive in the Processing and Electrochemical Behavior of Surface-Modified Si Anodes

In the present work, we explore the impact of conducting carbon on the processing of silicon (Si)-rich electrodes, their resulting cycling performance, and parasitic side reactions. We employed three different carbon additives, Super C45 (carbon black), Super C65 (carbon black), and TIMCAL C-NERGY KS 6L (graphite), with varying sizes and morphologies to determine how these parameters influence the structure and the electrochemical behavior of the cast electrodes. Raman mapping indicates that the improved performance achieved using C45 can be explained by the homogeneous distribution of Si and carbon, enabling the formation of continuous electrical pathways throughout the electrode. Further, this finding aligns with the results of ζ potential measurements, which indicate that C45 can maintain more stable dispersions in N-methyl-2-pyrrolidone (NMP) compared with the other carbon additives. However, electrodes with C45 as the conducting agent exhibited increased parasitic side reactions, as evidenced by the leakage current obtained from voltage hold experiments. These side reactions can have adverse effects on the calendar life of the electrode. Furthermore, the Raman maps of the electrodes reveal heterogeneities in Si and carbon distribution with lower carbon content, especially with only 2% carbon. This drastically impacts the cyclability of the electrodes, with portions of the low-carbon electrodes that remain unable to undergo cycling even at slow rates (0.2 Ah g –1 ). Additionally, we found that slower formation rates are favored in the context of parasitic side reactions, although slower formation rates can potentially create thicker passivating films that could hinder Li + -ion transport. Therefore, we emphasize the need for an intricate balance in materials selection and cycling protocol for optimal electrode processing and electrochemical behavior.

25 ENERGY STORAGE↗
DOE OSTI2024

Memory Effect on the Synthesis of Perovskite-Type Li-Ion Conductor Li x La 2/3– x /3 TiO 3 (LLTO)

The structural chemistry of the solid ion-conducting Li x La 2/3–x/3 TiO 3 (LLTO) is rich with various polymorphs related to atomic segregation. Here, we explored the LLTO reaction pathway from various structurally related precursors (La 2 LiO 3 H, Li 2 TiO 3 , and Li 4 Ti 5 O 12 ), focusing on the effects of LLTO-like structural motifs in precursors using a combination of experimental and computational techniques. Density functional theory (DFT) calculations revealed that the failure of syntheses to produce LLTO below 1300 °C is due to the presence of multiple competing low-energy phases that result in competitive byproduct formation. In all syntheses where T = 1300 °C, LLTO was the sole product; however, varying phase fractions of I4/mcm and P4/nbm polymorphs and double-perovskite P4/mmm can be obtained depending on the synthesis route. This is an unusual result as at 1300 °C, LLTO should only be the ideal cubic Pm-3m perovskite structure, yet there appears to be a memory effect from the different precursors resulting in the unique phase selectivity and stabilization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Battery with shear thickening, impact resistant electrolytes

A battery includes an anode, a cathode, and a porous separator having a surface and percolating pores providing a porosity of from 20% to 80%. A passively impact resistant composite electrolyte includes an electrolyte and electrically non-conducting particles that enable shear thickening. The particles can have a polydispersity index of no greater than 0.1, an average particle size in a range of from 50 nm to 1 um, and an absolute zeta potential of greater than ±40 mV. The shear thickening enabling particles can be from 10 wt. % to 40 wt. % of the total weight of the separator and shear thickening particles. Between 20-40 wt. % of the shear thickening enabling particles are located in the pores of the separator.

Armstrong, Beth L.↗
DOE OSTI2023

Method of making a passively impact resistant battery

A method of making a passively impact resistant battery includes the steps of providing a porous separator material having pores and a surface, and providing a suspension composition including shear thickening enabling particles and a particle suspension solvent for suspending the shear thickening enabling particles. The shear thickening particles have a polydispersity index of no greater than 0.1, an average particle size of in a range of 50 nm to 1 um, and an absolute zeta potential of greater than ±40 mV. The suspension composition is applied to the separator material, wherein a portion of the particles and suspension solvent penetrate the pores. The suspension solvent is evaporated from the separator material. An anode layer and a cathode layer are applied. An electrolyte composition is applied between the anode layer and the cathode layer. The electrolyte composition includes an electrolyte solvent and an electrolyte salt.

Armstrong, Beth L.↗
DOE OSTI2023

Carbon Coating Influence on the Formation of Percolating Electrode Networks for Silicon Anodes

Previous studies have demonstrated that chemical vapor deposition carbon coating on silicon (Si@C) can enhance the electrochemical performance of lithium-ion batteries with Si-based anodes. However, the underlying mechanisms contributing to this improvement have not been fully explored. Here, we address this knowledge gap by applying a suite of characterization methods to evaluate Si@C anodes prepared by reducing acetylene on ball-milled Si particles. Raman mapping measurements show that the C coating (<5 nm thick) enables a homogeneous Si and carbon distribution during the slurry casting process, thereby promoting Si utilization during cycling. The coating’s microstructure and morphology were evaluated using X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy, and neutron reflectivity experiments. Electrochemical impedance spectroscopy measurements upon cycling indicate that carbon coating also reduces the overall resistance as benchmarked against bare Si anodes. Galvanostatic cycling in half-cell studies revealed higher initial Coulombic efficiency and specific capacities with increasing carbon coating time. However, solid electrolyte interphase (SEI) investigations using XPS showed that the coated and uncoated samples have very similar characteristics, suggesting that the SEI may only play a minor role in enhancing the performance of Si@C. Full-cell evaluation of the Si electrodes was consistent with half-cell results relating to performance and SEI properties, further supporting the conclusion that electronic and ionic percolation, enabled by effective electrode manufacturing, are the dominant factors contributing to the favorable performance of Si@C.

25 ENERGY STORAGE↗
DOE OSTI2023

Critical Contribution of Imbalanced Charge Loss to Performance Deterioration of Si-Based Lithium-Ion Cells during Calendar Aging

Increasing the energy density of lithium-ion batteries, and thereby reducing costs, is a major target for industry and academic research. One of the best opportunities is to replace the traditional graphite anode with a high-capacity anode material, such as silicon. However, Si-based lithium-ion batteries have been widely reported to suffer from a limited calendar life for automobile applications. Heretofore, there lacks a fundamental understanding of calendar aging for rationally developing mitigation strategies. Both open-circuit voltage and voltage-hold aging protocols were utilized to characterize the aging behavior of Si-based cells. Particularly, a high-precision leakage current measurement was applied to quantitatively measure the rate of parasitic reactions at the electrode/electrolyte interface. The rate of parasitic reactions at the Si anode was found 5 times and 15 times faster than those of LiNi 0.8 Mn 0.1 Co 0.1 O 2 and LiFePO 4 cathodes, respectively. Here, the imbalanced charge loss from parasitic reactions plays a critical role in exacerbating performance deterioration. In addition, a linear relationship between capacity loss and charge consumption from parasitic reactions provides fundamental support to assess calendar life through voltage-hold tests. These new findings imply that longer calendar life can be achieved by suppressing parasitic reactions at the Si anode to balance charge consumption during calendar aging.

25 ENERGY STORAGE↗
DOE OSTI2023

Origin of rate limitations in solid-state polymer batteries from constrained segmental dynamics within the cathode

Currently, one of the key challenges preventing the wide commercialization of polymer-based solid-state batteries is achieving high-rate capabilities. This work unravels chain structure and segmental dynamics in a polymer-based composite cathode consisting of LiFePO 4 (LFP), carbon, and poly(ethylene oxide) (PEO) with lithium bis(trifluoromethanesulfonyl)imide. Small-angle neutron scattering (SANS) data reveal that PEO chains are adsorbed on the surface of LFP particles during slurry processing to make the composite electrode. The strong interaction between LFP and PEO chains leads to greatly reduced segmental dynamics of PEO, as discovered by quasi-elastic neutron scattering (QENS). The reduced segmental dynamics results in 70% decreased Li + mobility of the polymer electrolyte in the composite cathode. The combined SANS and QENS study indicates that one of the key bottlenecks that limits the rate performance of PEO-based polymer batteries originates from molecular interactions within the cathode.

25 ENERGY STORAGE↗