Search NASA⌕ Search

Engineering topics

Victor, B. S. (ORCID:0000000212512922)

Publications and source records attributed to Victor, B. S. (ORCID:0000000212512922).

Turbulence suppression at extreme plasma densities on DIII-D and EAST

Recent high-poloidal-beta (high-βP) experiments on DIII-D and EAST have made coordinated breakthroughs for high confinement quality at high density near the Greenwald limit. Density gradient amplification of turbulence suppression at high βP can explain both of these achievements. Experiments on DIII-D have achieved Greenwald fraction (fGr = line-averaged density/Greenwald density) above 1 simultaneously with normalized energy confinement (H98y2) around 1.5, as required in fusion reactor designs but never before verified in tokamak experiments with the divertor configuration. A synergy between increased H98y2 and fGr is observed with strong gas puffing, due to the build-up of an internal transport barrier at large radius in the temperature and density channels. Transport simulations reveal that the favorable trend of reduced turbulent energy transport at higher density is only expected when increasing the density gradient at high local safety factor and high β, thus at high βP to ensure strong α-stabilization. These conditions are crucial to many conceptual designs for steady-state reactors. New experiments on EAST have nearly doubled the ion temperature at fGr ∼ 0.9, consistent with predict-first modeling results based on the same physics revealed from the DIII-D analysis. All previous EAST long-pulse H-modes have Ti ≪ Te near plasma axis. Transport modeling indicates that the profiles are limited by ion-temperature-gradient modes at mid-radius. The modeling also suggested potential solutions, including reducing magnetic shear, enhancing density gradients, and higher impurity concentration. Following this guidance, EAST experiments directly show a strong enhancement of Ti achieved with a combination of a second plasma current ramp-up, a density gradient increase, and a Zeff perturbation by a short pulse (100 ms) of impurity injection, as predicted by the earlier modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Early internal detection of magnetic tearing and implications for tokamak magnetohydrodynamic stability

Internal fluctuation measurements with Faraday-effect polarimetry in the DIII-D tokamak reveal the onset of a tearing mode with toroidal mode number n = 3 well before it is detected by the sensing coils external to the plasma. This mode appears before the n = 2, 1 modes and is first detected with internal measurements at a lower value of the ideal-wall kink beta limit than is indicated at the time of first detection by the sensing coils. When the mode is first detected, the linear resistive stability parameter, Δ′, indicates marginal stability and continues to do so until later when the mode amplitude begins increasing linearly with time—together suggesting a neoclassical origin for this mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spectrally resolved polarization angle across the motional Stark effect spectrum

A new diagnostic technique has been developed that couples a spectrometer and an image-intensified camera into the traditional motional Stark effect (MSE) system on DIII-D. The image-intensified camera syncs with the photo-elastic modulators to spectrally resolve the Stokes parameters across the Stark multiplet. Polarization dependent phase shift, likely from a plasma facing mirror, leads to the spectropolarimeter measuring a variation in the polarization angle across the MSE spectrum of ∼8°.

Victor, B. S. (ORCID:0000000212512922)↗

Improved motional Stark effect signal processing using fast Fourier transform spectral analysis

A Fast Fourier Transform (FFT) based method has been developed, which improves the frequency response of the Motional Stark Effect (MSE) system by about a factor of 10 over the conventional analog lock-in method. The method uses fits to rigorously derived analytic expressions for the FFT spectral components of the MSE signal to accurately obtain the amplitudes and phases of the 2f1 and 2f2 photo-elastic modulator (PEM) frequencies that encode the polarization angle. Since no frequency filtering is used in the FFT method, the frequency response is limited by fundamental measurement properties: the frequency response of the detector, photon statistics, sample rate, and the ability to resolve the spectral components. In contrast, the frequency response of the analog lock-in is limited by a low pass filter with a cutoff of around 500 Hz. In the case of the DIII-D MSE system, the output of the photo-multiplier tube detector was sampled at 500 kHz and FFTs with as few as 100 points were used to obtain the amplitudes of the 2f1 and 2f2 PEM frequency components. This corresponds to a frequency response of 5 kHz, about ten times faster than the analog lock-in amplifier system. Details of the FFT method will be presented and compared to those of the analog lock-in system.

Makowski, M. A.↗