Search NASA⌕ Search

Engineering topics

Wang, Gang

Publications and source records attributed to Wang, Gang.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Bulk high-temperature superconductivity in pressurized tetragonal La 2 PrNi 2 O 7

The Ruddlesden–Popper (R–P) bilayer nickelate, La 3 Ni 2 O 7 , was recently found to show signatures of high-temperature superconductivity (HTSC) at pressures above 14 GPa . Subsequent investigations achieved zero resistance in single-crystalline and polycrystalline samples under hydrostatic pressure conditions. Yet, obviousdiamagnetic signals, the other hallmark of superconductors, are still lacking owing to the flamentary nature with low superconducting volume fraction. The presence of a new 1313 polymorph and competing R–P phases obscured proper identification of the phase for HTSC. Thus, achieving bulk HTSC and identifying the phase at play are the most prominent tasks. Here we address these issues in the praseodymium (Pr)-doped La 2 PrNi 2 O 7 polycrystalline samples. We find that substitutions of Pr for La efectively inhibit the intergrowth of diferent R–P phases, resulting in a nearly pure bilayer structure. For La 2 PrNi 2 O 7 , pressure-induced orthorhombic to tetragonalstructural transition takes place at P c ≈ 11 GPa, above which HTSC emerges gradually on further compression. The superconducting transition temperatures at 18–20 GPa reach $T$ $^{onset}_{c}$ = $82.5$ $K$ and $T$ $^{zero}_{c}$ = $60$ $K$, which are the highest values, to our knowledge, among known nickelate superconductors. Importantly, bulk HTSC was testified by detecting clear diamagnetic signals below about 75 K with appreciable superconducting shielding volume fractions at a pressure of above 15 GPa. Further, our results not only resolve the existing controversies but also provide directions for exploring bulk HTSC in the bilayer nickelates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

The EIC accelerator: design highlights and project status

The design of the electron-ion collider (EIC) at Brookhaven National Laboratory is well underway, aiming at a peak electron-proton luminosity of 10e+34 cm^-1·sec^-1. This high luminosity, the wide center-of-mass energy range from 29 to 141 GeV (e-p) and the high level of polarization require innovative solutions to maximize the performance of the machine, which makes the EIC one of the most challenging accelerator projects to date. The complexity of the EIC will be discussed, and the project status and plans will be presented.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Influence of globally spin-aligned vector mesons to the measurements of the chiral magnetic effect in heavy-ion collisions

The chiral magnetic effect (CME) in high-energy heavy-ion collisions arises from the interplay between the chirality imbalance and the intense magnetic field and will cause a charge separation along the magnetic field direction. While the CME search is still ongoing in experiments, the non-CME contributions need to be excluded from the CME observables. In this work, we examine the influence of globally spin-aligned ρ mesons on the γ 112 correlator, the R Ψ 2 (ΔS) correlator, and the signed balance functions, via a toy model and a multiphase transport model (AMPT). We find that the CME observables are sensitive to the 00-component of the spin density matrix, ρ 00 : they receive positive (negative) contributions when ρ 00 is larger (smaller) than 1/3.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Relations between Shot Noise, Gain Bandwidth, and Saturation of Instabilities

There are numerous instabilities present in charged particle beams that undergo exponential growth and reach saturation. In various applications, such as free-electron lasers or micro-bunching light sources, achieving saturation is desirable. Conversely, there are applications where these instabilities are utilized as linear broad-band amplifiers for signals embedded in the charged beam. In the latter scenario, the saturation of an instability induces non-linear distortions in the imprinted signal, thereby limiting the useful range of such amplifiers. Accurate evaluation of these instabilities necessitates a complete and comprehensive modeling approach that includes shot noise within the beam. Unfortunately, such modeling is not always feasible or practical. In this paper, we introduce a methodology utilizing the frequency and bandwidth of the instability as key parameters. Through this, we derive an estimation for the range of linear instability growth. Our derivation is conducted in a model-independent manner, making it applicable to a broad spectrum of instabilities. To validate our approach, we employ established and thoroughly benchmarked simulations with a free electron laser (FEL) code as well as self-consistent 3-dimensional simulation of plasma-cascade instability using code SPACE.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Development and Validation of Home Comfort System for Total Performance Deficiency/Fault Detection and Optimal Comfort Control

In this project, we developed and tested a learning-based home thermal model that facilitates the operation of a model predictive control (MPC)-based optimization agent and an automated fault detection and diagnosis (AFDD) agent. The home thermal model was constructed using a two-node resistor-capacitor model. Moreover, two accompanying parameter identification methods were introduced, least-squares and optimization. Based on the home thermal model, the MPC-based optimization agent was developed to optimize residential HVAC operation. Using two FDD methods, the AFDD agent was constructed to detect and diagnose two prevalent residential AC faults, airflow reduction and refrigerant undercharge. The home thermal model, along with the MPC-based optimization agent and AFDD agent, were tested at the Norman Test House, Miami Test House, Pacific Northwest National Laboratory (PNNL) Test House A, and PNNL Test House B. Finally, they were also field tested in nine demonstration homes with real occupants.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Direct Synthesis of Layer-Tunable and Transfer-Free Graphene on Device-Compatible Substrates Using Ion Implantation Toward Versatile Applications

Direct synthesis of layer-tunable and transfer-free graphene on technologically important substrates is highly valued for various electronics and device applications. State of the art in the field is currently a two-step process: a high-quality graphene layer synthesis on metal substrate through chemical vapor deposition (CVD) followed by delicate layer transfer onto device-relevant substrates. Here, we report a novel synthesis approach combining ion implantation for a precise graphene layer control and dual-metal smart Janus substrate for a diffusion-limiting graphene formation to directly synthesize large area, high quality, and layer-tunable graphene films on arbitrary substrates without the post-synthesis layer transfer process. Carbon (C) ion implantation was performed on Cu–Ni film deposited on a variety of device-relevant substrates. A well-controlled number of layers of graphene, primarily monolayer and bilayer, is precisely controlled by the equivalent fluence of the implanted C-atoms (1 monolayer ~4 × 10 15 C-atoms/cm 2 ). Upon thermal annealing to promote Cu-Ni alloying, the pre-implanted C-atoms in the Ni layer are pushed toward the Ni/substrate interface by the top Cu layer due to the poor C-solubility in Cu. As a result, the expelled C-atoms precipitate into a graphene structure at the interface facilitated by the Cu-like alloy catalysis. After removing the alloyed Cu-like surface layer, the layer-tunable graphene on the desired substrate is directly realized. The layer-selectivity, high quality, and uniformity of the graphene films are not only confirmed with detailed characterizations using a suite of surface analysis techniques but more importantly are successfully demonstrated by the excellent properties and performance of several devices directly fabricated from these graphene films. Molecular dynamics (MD) simulations using the reactive force field (ReaxFF) were performed to elucidate the graphene formation mechanisms in this novel synthesis approach. With the wide use of ion implantation technology in the microelectronics industry, this novel graphene synthesis approach with precise layer-tunability and transfer-free processing has the promise to advance efficient graphene-device manufacturing and expedite their versatile applications in many fields.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Minijet clustering algorithm using transverse-momentum seeds in high-energy nuclear collisions

We propose an algorithm to detect mini-jet clusters in high-energy nuclear collisions, by selecting a high-transverse-momentum (pT) particle as a seed and assigning a clustering radius (R) in the pseudorapidity and azimuthal-angle space. Our PYTHIA simulations for p+p collisions show that a scheme with a seeding p T of around 0.5 GeV/c and R of approximately 0.6 satisfactorily identifies mini-jet clusters. The correlation between clusters obtained in PYTHIA calculations using the algorithm exhibits the proper behavior of hard-scattering-like processes, suggesting its usefulness in isolating mini-jet-like clusters from non-hard-scattering soft processes when applied to actual nuclear-collision data, thereby allowing a closer examination of both the mini-jet and the soft mechanisms.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Performance Demonstration of an Occupancy Sensor-enabled Integrated Solution for Commercial Buildings

Traditionally, a single-loop fixed-gain controller is applied to supply fan (SF) and cooling coil (CC) valve controls while a fixed-damper position control is applied to outdoor air (OA) damper control at air handling units (AHUs) in commercial buildings. With the increasing application of occupancy sensors, the information generated by occupancy sensors is applied to not only reduce the electricity loads from lighting and controllable plug loads, but also reset OA intake and minimum supply airflow setpoints. Meanwhile, these intermittent operation actions greatly elevate the dynamics of AHU systems, which may introduce unstable SF and CC valve operations and inaccurate OA flow control at AHUs and consequently degrade maximum energy efficiency gains. With virtual fan and valve flow meter technologies, two advanced controls, including cascade control and gain scheduling control, can be implemented on both the SF and CC valve, and an advanced control using a virtual OA flow meter can be implemented on OA damper integrated with occupancy sensors. The goal of this project is to demonstrate the savings, cost, and performance of an integrated solution that integrates the three advanced HVAC controls with occupancy sensors to allow accurate and stable AHU operations in real buildings. The project objectives are to: 1) develop and validate an advance SF control algorithm; 2) develop and validate an advanced CC valve control algorithm; 3) validate an algorithm to implement a virtual OA flow meter; and 4) demonstrate the savings, cost, and performance of the integrated solution in real buildings. The technical approaches are to: 1) select a test system at the University of Oklahoma; 2) develop and implement the algorithms of advanced SF and CC valve controls and validate the performance; 3) develop and implement the advanced OA control using a virtual OA flow meter and validate the performance; 4) demonstrate the savings, cost, and performance of the proposed integrated solution with and without three advanced HVAC controls; and 5) disseminate the project results through publications and presentations. For the SF control, both the gain scheduling and cascade controls can improve the fan energy performance by reducing the fan power during the transient period and the fan control performance at lower speeds by reducing fan speed variation. Moreover, the gain scheduling control provides a simple and low-cost solution and is recommended. The fan power savings can reach 30% in a transient period. For the CC valve control, the gain scheduling control can considerably reduce the supply air temperature oscillation range and frequency under both higher and lower load conditions and the control valve response is much more stable. As a result, the gain scheduling control is recommended. The projected pump energy consumption can be reduced by 68.5%. With the developed virtual OA flow meter, the OA can be accurately controlled at its setpoint, which is determined based on the actual number of occupants in the building provided by occupancy sensors. The RMSE of the proposed OA control is 15.9 L/s. The energy data shows that the fan power and CC cooling energy were significantly reduced. On the other hand, the energy savings majorly results from the occupancy sensors and the energy savings by the advanced HVAC controls is minimal because that the controllers in the test AHU were tuned with very slow response. An annual technical savings potential is estimated as 0.5 quads in the commercial sector.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Mechanical, Morphological, and Charge Transport Properties of NDI Polymers with Variable Built‐in Π‐Conjugation Lengths Probed by Simulation and Experiment

Abstract Mechanically deformable polymeric semiconductors are a key material for fabricating flexible organic thin‐film transistors (FOTFTs)—the building block of electronic circuits and wearable electronic devices. However, for many π‐conjugated polymers achieving mechanical deformability and efficient charge transport remains challenging. Here the effects of polymer backbone bending stiffness and film microstructure on mechanical flexibility and charge transport are investigated via experimental and computational methods for a series of electron‐transporting naphthalene diimide (NDI) polymers having differing extents of π‐conjugation. The results show that replacing increasing amounts of the π‐conjugated comonomer dithienylvinylene (TVT) with the π‐nonconjugated comonomer dithienylethane (TET) in the backbone of the fully π‐conjugated polymeric semiconductor, PNDI‐TVT 100 (yielding polymeric series PNDI‐TVT x , 100 ≥x≥ 0), lowers backbone rigidity, degree of texturing, and π–π stacking interactions between NDI moieties. Importantly, this comonomer substitution increases the mechanical robustness of PNDI‐TVT x while retaining efficient charge transport. Thus, reducing the TVT content of PNDI‐TVT x suppresses film crack formation and dramatically stabilizes the field‐effect electron mobility upon bending (e.g., 2 mm over 2000 bending cycles). This work provides a route to tune π–π stacking in π‐conjugated polymers while simultaneously promoting mechanical flexibility and retaining good carrier mobility in FOTFTs.

Chemistry↗
DOE OSTI2023

Updates on the Wake Potential Calculations for the Electron-ion Collider with ECHO3D

ECHO3D has been used for calculating the geometric impedance and short-range wakefields for several EIC (Electron-Ion Collider) beamline vacuum components in the past few years. This note summarizes the wake potential calculations conducted in 2023 with ECHO3D for components from both the hadron storage ring (HSR) and the electron storage ring (ESR). For the HSR, calculations have been carried out for the polarimeter, the beam screen with pump slots and the bellow with pump ports. For the ESR, the short-range wake potential for the flange weld as well as various designs of the storage ring cavity have been calculated.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Loose Belt Fault Detection and Virtual Flow Meter Development Using Identified Data-driven Energy Model for Fan Systems

An energy model that correlates fan airflow, head, speed, and system power input is essential to detect device faults and optimize control strategies in fan systems. Since the application of variable-frequency drives (VFDs) makes the motor-efficiency data published by manufacturers inapplicable for VFD–motor–fan systems, the fan efficiency and drive (belt–motor–VFD) efficiency must be identified for each individual system to obtain accurate energy models. The objectives of this paper are to identify an energy model of existing VFD–motor–fan systems using available experimental data and demonstrate its applications in loose belt fault detection and virtual airflow meter development for optimal control. First, an approach is developed to identify the fan head, fan efficiency, and drive-efficiency curves using available fan head, speed, and system power input as well as temporarily measured airflow rate without measuring shaft power. Then, the energy model is identified for an existing VFD–motor–fan system. Finally, the identified model is applied to detect the slipped belt faults and develop the virtual airflow meter. The experiment results reveal that the developed approach can effectively obtain the energy model of VFD–motor–fan systems and the model can be applied to effectively detect slipped belt faults and accurately calculate the fan airflow rate.

42 ENGINEERING↗
DOE OSTI2023

Synthesis of 2H/ fcc -Heterophase AuCu Nanostructures for Highly Efficient Electrochemical CO 2 Reduction at Industrial Current Densities

Structural engineering of nanomaterials offers a promising way for developing high-performance catalysts toward catalysis. However, the delicate modulation of thermodynamically unfavorable nanostructures with unconventional phases still remains a challenge. Here, in this study, the synthesis of hierarchical AuCu nanostructures is reported with hexagonal close-packed (2H-type)/face-centered cubic (fcc) heterophase, high-index facets, planar defects (e.g., stacking faults, twin boundaries, and grain boundaries), and tunable Cu content. The obtained 2H/fcc Au 99 Cu 1 hierarchical nanosheets exhibit excellent performance for the electrocatalytic CO 2 reduction to produce CO, outperforming the 2H/fcc Au 91 Cu 9 and fcc Au 99 Cu 1 . The experimental results, especially those obtained by in-situ differential electrochemical mass spectroscopy and attenuated total reflection Fourier-transform infrared spectroscopy, suggest that the enhanced catalytic performance of 2H/fcc Au 99 Cu 1 arises from the unconventional 2H/fcc heterophase, high-index facets, planar defects, and appropriate alloying of Cu. Impressively, the 2H/fcc Au 99 Cu 1 shows CO Faradaic efficiencies of 96.6% and 92.6% at industrial current densities of 300 and 500 mA cm -2 , respectively, as well as good durability, placing it among the best CO 2 reduction electrocatalysts for CO production. The atomically structural regulation based on phase engineering of nanomaterials (PEN) provides an avenue for the rational design and preparation of high-performance electrocatalysts for various catalytic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Evaluation of supply air temperature control performance with different control strategies at air handling units

Due to its nonlinear feature, supply air temperature control systems at air handling units using single-loop fixed gain control frequently suffer unstable response under dynamic conditions. This paper is aimed at identifying a more effective control strategy to stabilize the valve control and achieve desirable supply air temperature response under various operation conditions by evaluating three control strategies, cascade, gain scheduling and cascade plus gain scheduling controls. Firstly, a control-oriented model is developed and calibrated through open-loop tests. Then, the control issues with single-loop fixed gain control are evaluated through simulations and field tests, which indicates that the system has more aggressive response or becomes unstable under lower load conditions when the chilled-water flow rate is less than 0.1 L/s. Finally, three control strategies are proposed and evaluated. Further, the results reveal that all three proposed controls can achieve better robustness with the integral square error of supply air temperature decreased to 16%, 47% and 5%, respectively, under lower load condition. However, since high-frequency oscillation of the control valve occurs with cascade and cascade plus gain scheduling control, the gain scheduling control is recommended considering a trade-off among the supply air temperature response, valve lifetime and implementation complexity.

42 ENGINEERING↗
DOE OSTI2023

Fourier coefficients of noninterdependent collective motions in heavy-ion collisions

Here, we present a scenario in heavy-ion collisions where different modes of collective motions are noninterdependent, driven by factorized actions in the created nuclear medium. Such physics mechanisms could each dominate at a distinct evolution stage, or coexist simultaneously. If the probability of particle emission is modulated by each nondependent collective motion with a single-harmonic Fourier expansion, the particle azimuthal distribution should be the product of all these expansions. Consequently, nonleading cross terms between collectivity modes appear, and their contributions to experimental observables could be significant. In particular, we argue that the chiral magnetic effect (CME) and elliptic flow can develop separately, with their convolution affecting the observable that is sensitive to the shear-induced CME. We will use the event-by-event anomalous-viscous fluid dynamics model to illustrate the effects of this scenario. Besides giving insights into searches for the CME, we also propose feasible experimental tests based on conventional flow harmonics, and demonstrate the emergence of nonleading cross terms with a multiphase transport model.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Development, calibration, and validation of a novel gray-box energy model for residential split air conditioners

Energy models for vapor compression refrigeration in residential air conditioners have been developed through white-box, gray-box, and black-box methods in decades. However, existing white-box and gray-box models require complicated equations with detailed geometries while black-box models require substantial experimental data. Further, this paper aims to develop and validate a simple gray-box steady-state energy model without the need for detailed geometries, which can accurately predict the cooling capacity and electrical power input based on outdoor and indoor air conditions, and supply airflow rates. First three state variables, including the evaporation and condensation temperatures, and refrigerant mass flowrate, are applied to develop the energy model and are solved by three physical equations, including the energy conservations at the evaporator and condenser, and the refrigerant volume-mass flow correlation of the compressor. Secondly, seven performance property functions related to three state variables and three physical equations are identified and calibrated by simple temperature and power measurements. Finally, field experiments are conducted on a residential air conditioner to calibrate these performance property functions and validate the developed model. The validated results reveal the model can accurately predict the cooling capacity and electrical power input, with the normalized root mean square errors of 2.3% and 0.87% respectively.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

3D theory of microscopic instabilities driven by space-charge forces

Microscopic, or short-wavelength, instabilities are known for a drastic reduction of the beam quality and strong amplification of the noise in a beam. Space charge and coherent synchrotron radiation are known to be the leading causes of such instabilities. In this paper, we present a rigorous 3D theory of such instabilities driven by the space-charge forces. We define the condition when our theory is applicable to an arbitrary accelerator system with 3D coupling. Finally, we derive a linear integral equation describing such instability and identify conditions when it can be reduced to an ordinary second-order differential equation.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Impact of globally spin-aligned vector mesons on the search for the chiral magnetic effect in heavy-ion collisions

In high-energy heavy-ion collisions, the chiral magnetic effect (CME) is predicted to arise from the interplay between the chirality imbalance of quarks in the nuclear medium and the intense magnetic field, and will cause a charge separation along the magnetic field direction. While the search for the CME is still ongoing in experiments at Relativistic Heavy Ion Collider (RHIC) and the Large Hadron Collider (LHC), the CME-sensitive observables need to be scrutinized to exclude the non-CME contributions. In this work, we examine the influence of globally spin-aligned ρ mesons on the γ 112 correlator, the R Ψ 2 (ΔS) correlator, and the signed balance functions, via a toy model and a multiphase transport model (AMPT). The global spin alignment of vector mesons could originate from non-CME mechanisms in heavy-ion collisions, and is characterized by the 00-component of the spin density matrix, ρ 00 . Here, we find that the CME observables show similar dependence on ρ 00 , and could receive a positive (negative) contribution from ρ-decay pions, if the ρ 00 of ρ mesons is larger (smaller) than 1/3. Since pions are the most abundant particles in such collisions, the ρ 00 measurements for ρ mesons become crucial to the interpretation of the CME data.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗