Engineering topics

Wang, Peng

Publications and source records attributed to Wang, Peng.

7 records

DOE OSTI2024

Discerning the effect of various irradiation modes on the corrosion of Zircaloy-4

Using proton irradiation, this study investigates the individual influence of several factors on the corrosion kinetics of Zircaloy-4 in a hydrogenated water environment simulating a Pressurized Water Reactor (PWR). Using both simultaneous irradiation-corrosion and autoclave corrosion, we separately examine: (i) the effect of pre-irradiation on modifying the structure of the material, (ii) the impact of irradiation on creating defects in the growing oxide layer during corrosion, and (iii) the influence of irradiation on increasing the corrosion potential through radiolysis during corrosion. To replicate neutron-irradiated microstructure, two proton pre-irradiation schedules were employed: Schedule 1 (isothermal irradiation at 350 °C to 5 dpa) to simulate high-temperature PWR conditions, and Schedule 2 (two-step process: irradiation to 2.5 dpa at -10 °C followed by 2.5 dpa at 350 °C) to simulate lower temperature PWR and Boiling Water Reactor (BWR) conditions. Long-term autoclave corrosion testing over 360 days at 320 °C revealed no significant difference between unirradiated samples and those pre-irradiated according to either schedule, with all samples exhibiting sub-cubic kinetics within the pre-transition regime. Irradiated samples underwent Simultaneous Irradiation Corrosion (SIC) tests, corroding in 320 °C water while being irradiated with protons. Corrosion was found to accelerate in all SIC-tested samples relative to autoclave conditions, with the greatest increase observed in non-pre-irradiated samples. Pre-irradiation with either schedule resulted in a slower corrosion rate compared to non-pre-irradiated regions under SIC conditions. The degree of radiolysis observed in the SIC tests surpassed typical PWR conditions, approaching levels found in BWRs. Radiolysis products were identified as the primary contributors to accelerated corrosion, corroborated by radiolysis bar tests. Furthermore, these findings underscore the intricate interactions between irradiation, corrosion, and water chemistry in determining Zircaloy-4 corrosion kinetics within nuclear reactor environments.

Pressurized Water Reactor↗

DOE OSTI2024

Statistical properties of filaments in the cosmic web

ABSTRACT In the context of the cosmological and constrained Exploring the Local Universe with the reConstructed Initial Density field (ELUCID) simulation, this study explores the statistical characteristics of filaments within the cosmic web, focussing on aspects such as the distribution of filament lengths and their radial density profiles. Using the classification of the cosmic web environment through the Hessian matrix of the density field, our primary focus is on how cosmic structures react to the two variables $R_{\rm s}$ and $\lambda _{\rm th}$. The findings show that the volume fractions of knots, filaments, sheets, and voids are highly influenced by the threshold parameter $\lambda _{\rm th}$, with only a slight influence from the smoothing length $R_{\rm s}$. The central axis of the cylindrical filament is pinpointed using the medial-axis thinning algorithm of the COsmic Web Skeleton (COWS) method. It is observed that median filament lengths tend to increase as the smoothing lengths increase. Analysis of filament length functions at different values of $R_{\rm s}$ indicates a reduction in shorter filaments and an increase in longer filaments as $R_{\rm s}$ increases, peaking around $2.5R_{\rm s}$. The study also shows that the radial density profiles of filaments are markedly affected by the parameters $R_{\rm s}$ and $\lambda _{\rm th}$, showing a valley at approximately $2R_{\rm s}$, with increases in the threshold leading to higher amplitudes of the density profile. Moreover, shorter filaments tend to have denser profiles than their longer counterparts.

Zhang, Youcai (ORCID:0000000319674091)↗

DOE OSTI2024

More Heavy Precipitation in World Urban Regions Captured Through a Two‐Way Subgrid Land‐Atmosphere Coupling Framework in the NCAR CESM2

Abstract Current global climate models (GCMs), limited to grid‐scale land‐atmosphere coupling, cannot represent subgrid urban‐rural precipitation contrasts. This study develops an innovative two‐way subgrid land‐atmosphere coupling framework in the National Center for Atmospheric Research (NCAR) Community Earth System Model version 2 (CESM2) to explicitly resolve land‐atmosphere interaction over subgrid individual land units. Results show that urban heat island (UHI) leads to the urban rainfall effect (URE), which in turn alleviates overestimated UHI over China in CESM2. The URE manifests as a shift toward more heavy precipitation and less light precipitation in world urban areas than in surrounding rural counterparts. This feature is consistent with available observations. In heavy precipitation situations, the UHI promotes atmospheric instability and enhances atmospheric water vapor holding capacity, resulting in more heavy precipitation in urban areas. Conversely, in light precipitation situations, the UHI and decreased evaporation from urban impermeable surfaces diminish atmospheric relative humidity, suppressing light precipitation.

Geology↗

DOE OSTI2024

System Modeling and Robust Stability Region Analysis for Multi-inverters Based on VSG

As the number of inverter-interfaced distributed generators (IIDGs) increases, the decrease in the inertia of the microgrid affects the stability of microgrid voltage and current. The virtual synchronous generator (VSG) control method simulates the output characteristics of the synchronous machine to improve the inertia and damping of the microgrid. However, low-frequency oscillations can occur in systems with multi-VSGs connected in parallel, primarily when operating in island mode. Therefore, this article develops the small-signal state-space model for multi-inverters based on VSG and analyses the robust stability region (RSR) of the control parameters. Firstly, an extensible small-signal state-space model is established and simplified in the dq axis, which is a necessary preprocessing for the subsequent stability analysis. Secondly, the guardian map method based on bialternate product operation is constructed, and the RSR is established through translation mapping and rotation mapping. Therefore, the solution of RSR is transformed into the problem of identifying the Hurwitz matrix. Finally, the simulations and experiments verify that the calculated region can ensure stable operation during startup and meet the requirement to suppress low-frequency oscillations. In conclusion, the method of solving RSR proposed in this paper provides a basis for selecting controller parameters in practical engineering.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2024

Directing CO 2 electroreduction pathways for selective C 2 product formation using single-site doped copper catalysts

Manipulating the selectivity-determining step in post-C–C coupling is crucial for enhancing C 2 product specificity during electrocatalytic CO 2 reduction, complementing efforts to boost rate-determining step kinetics. Here we highlight the role of single-site noble metal dopants on Cu surfaces in influencing C–O bond dissociation in an oxygen-bound selectivity-determining intermediate, steering post-C–C coupling toward ethylene versus ethanol. Integrating theoretical and experimental analyses, we demonstrate that the oxygen binding strength of the Cu surface controls the favorability of C–O bond scission, thus tuning the selectivity ratio of ethylene-to-ethanol. The Rh-doped Cu catalyst with optimal oxygen binding energy achieves a Faradaic efficiency toward ethylene of 61.2% and an ethylene-to-ethanol Faradaic efficiency ratio of 4.51 at –0.66 V versus RHE (reversible hydrogen electrode). Integrating control of both rate-determining and selectivity-determining steps further raises ethylene Faradaic efficiency to 68.8% at 1.47 A cm -2 in a tandem electrode. Our insights guide the rational design of Cu-based catalysts for selective CO 2 electroreduction to a single C 2 product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

The Integrated Reference Region Analysis for Parallel DFIGs’ Interfacing Inductors

Although the traditional design of doubly-fed induction generators (DFIGs)’ interfacing inductors consider the peak ripple of the grid-side converter (GSC)’s output current, it does not consider the inductors’ impact on DFIGs’ smallsignal stability. Located in series between the GSC and the stator, the inappropriate selection of the interfacing inductor can easily result to system instability. Therefore, this paper first proposes the integrated reference region analysis for small wind farm's interfacing inductors to improve the traditional design method. Firstly, a new detailed parallel DFIGs’ smallsignal model that considers output currents’ coupling is built in d-q coordinate system with state-space approach. The model focuses on representing the operating states of parallel DFIGs in wind farm. Secondly, the linearized state-space matrix of parallel DFIGs is decomposed into nominal-value matrix and location matrix. Considering the traditional design requirements, the integrated reference region for interfacing inductor is proposed through spectral radius and bialternate matrix sum (BMS). Furthermore, it can provide better guidance for parameter selecting and stabilization method researches. Finally, the simulation and experimental results show that the proposed integrated reference region for parallel DFIGs’ interfacing inductors is accurate and instructive.

47 OTHER INSTRUMENTATION↗

DOE OSTI2024

Intermetallic Ni 3 Ga 1 Catalyst for Efficient Ammonia Reforming of Light Alkane

Ammonia reforming of light alkane is conventionally employed for HCN production where coproduct H 2 is burned for heating owing to the high reaction temperature (1200 °C) of such a highly endothermic process. Here, in this study, we show that a Ni 3 Ga 1 intermetallic compound (IMC) catalyst is highly efficient for such a reaction, realizing efficient conversion of C1–C3 alkanes at 575–750 °C. This makes it feasible for on-purpose CO x -free H 2 production assuming that ammonia, as an H 2 carrier, is ubiquitously available from renewable energy. At 650 °C and an alkane/ammonia ratio of 1/2, ethane and propane conversion of ~20% and methane conversion of 13% were obtained (with nearly 100% HCN selectivity for methane and ethane) over the unsupported Ni 3 Ga 1 IMC, which also shows high stability due to the absence of coke deposition. This breakthrough is achieved by employing a stoichiometric Ni 3 Ga 1 mixed oxalate solid solution as the precursor for the Ni 3 Ga 1 IMC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗